• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전력기술부문
• /
• pp.174-177
• /
• 2003

Kinds of most frequent faults happened on overhead distribution system are the single line-to-ground fault, the line-to-line fault and the two line-to-ground fault. Occasionally, the three line-to-ground fault and the disconnection of a wire are happened in severe conditions. In this study, the single line-to-ground fault, the line-to-line fault, two line-to-ground fault on three-phase four-wire overhead distribution system were experimentally simulated and characteristics of total leakage current of distribution arrester caused by these faults were investigated. Also, the changing aspect of total leakage current of distribution arrester caused by voltage variation was investigated. In a consequence, abnormal voltages caused by voltage variation, the line-to-line fault, the two line-to-ground fault have a little effect on total leakage current of ZnO arrester. But abnormal voltages caused by the single line-to-ground fault have an important effect on total leakage current of ZnO arrester.

• Tribology and Lubricants
• /
• 제39권2호
• /
• pp.61-71
• /
• 2023

This study proposes a procedure for designing a labyrinth seal that meets both leakage flow rate and rotordynamic performance criteria (effective damping, amplification factor, separation margin, logarithmic decrement, and vibration amplitude). The seal is modeled using a one control volume (1CV) bulk flow approach to predict the leakage flow rate and rotordynamic coefficients. The rotating shaft is modeled with the finite element (FE) method and is assumed to be supported by two linearized bearings. Geometry, material and operating conditions of the rotating shaft, and the supporting characteristics of the bearings were fixed. A single labyrinth seal is placed at the center of the rotor, and the linearized dynamic coefficients predicted by the seal numerical model are inserted as linear springs and dampers at the seal position. Seal designs that satisfy both leakage and rotordynamic performance are searched by modifying five seal design parameters using the multi-grid method. The five design parameters include pre-swirl ratio, number of teeth, tooth pitch, tooth height and tooth tip width. In total, 12500 seal models are examined and the optimal seal design is selected. Finally, normalization was performed to select the optimal labyrinth seal designs that satisfy the system performance requirements.

• 조명전기설비학회논문지
• /
• 제23권2호
• /
• pp.161-167
• /
• 2009

저전압용 절연체로 사용되는 유기절연재료는 누설전류에 의하여 탄화되는 경우 고유한 탄화특성을 나타낸다. 그러므로 유기절연재료의 탄화특성을 이용함으로써 유기절연재료의 표면을 흐르는 누설전류로 인한 전기화재를 규명하는 것이 가능하다. 이와 같은 탄화특성을 이해하기 위하여 본 논문에서는 대표적인 유기절연체로 알려진 페놀수지, PVC, 그리고 아크릴수지를 누설전류에 의하여 탄화시키는 실험을 수행하고 시료의 탄화패턴과 적외선 흡광 스펙트럼을 분석하였다. 탄화패턴 분석에 의하면 페놀수지는 열경화성 성질 때문에 소위 'spider-leg'의 탄화패턴이 형성된다. 페놀수지와 다르게 PVC와 아크릴 수지의 표면에서는 열가소성 성질 때문에 탄화원인을 규명할 수 있을 정도의 분명한 탄화패턴을 관찰하기 어렵다. 이 경우 적외선 흡광 스펙트럼의 분석을 통하여 누설전류로 인하여 탄화된 시료의 특성을 규명할 수 있다 분석결과, 누설전류에 의해 탄화된 PVC의 경우에 파수 $3,400[cm^{-1}]$, $1,618[cm^{-1}]$에서 흡광피크가 검출되었으며 이것은 탄화원인을 규명할 수 있는 중요한 인자가 될 수 있다.

• 한국재료학회지
• /
• 제11권12호
• /
• pp.1080-1085
• /
• 2001

Dielectric properties and leakage current characteristics of 100 nm-thick $Ta_2O_5/Al_2O_3$multilayer thin films, which were fabricated by reactive sputtering of$Al_2O_3$and$Ta_2O_5$ successively on top of each other for total 9 layers, have been investigated with variation of the$Al_2O_3$content$(i.e,\;Ta_2O_5/Al_2O_3 \;thickness\;ratio)$.$Ta_2O_5/Al_2O_3$films were amorphous regardless of the$Al_2O_3$content. With increasing the$Al_2O_3$content from 0% to 100%, refractive index of the $Ta_2O_5/Al_2O_3$films decreased linearly from 2.03 to 1.56 and dielectric constant was lowered from 23.9 to 7.7 Variation of the dielectric constant with the$Al_2O_3$content was in good agreement with the behavior that was obtained by assuming parallel capacitors of$Al_2O_3$and Ta_2O_5$. Leakage current characteristics of $Ta_2O_5/Al_2O_3$ multilayer films were superior to those of $Ta_2O_5$ and$Al_2O_3$films. $Ta_2O_5/Al_2O_3$ films of 5% and 10%$Al_2O_3$content exhibited excellent leakage current densities which were lower than $10^{-7} A/cm^2$ at 1MV/cm.

• 한국수소및신에너지학회논문집
• /
• 제31권3호
• /
• pp.328-336
• /
• 2020

In the Francis turbine, the leakage flow through the runner gaps which are between the runner and the stator structure influences the internal flow and hydraulic performance. Thus, the investigation for the flow characteristics induced by the runner gaps is important. However, the runner gaps are often disregarded by considering the time and cost of the numerical analysis. Therefore, in this study, the flow characteristics according to runner gaps of the Francis turbine model were investigated including the leakage flow of the runner cone. The three-dimensional unsteady Reynolds-averaged Navier-Stokes analyses were conducted using a scale-adaptive simulation shear stress transport as a turbulence model for observing the influence of the leakage flow on the internal flow and hydraulic performance. The efficiencies were decreased slightly with runner gaps; and the complicated flows were captured in the gaps.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권5호
• /
• pp.319-325
• /
• 1999

Direct current(d.c.)leakage current voltage characteristics of radio-frequencymagnetron sputtered BaTa\sub 2\O\sub 6\ film capacitors with aluminum(A1) top and indium tin oxide (ITO) bottom electrodes have been investigatedas a function of applied field and temperature. In order to study surfacetreatment effect on the electrical characteristics of as-deposited film weperformed exposure of oxygen plasma on $BaTa_2O_6$ surface. d. c.current-voltage (I-V), bipolar pulse charge-voltage (Q-V), d. c. current-time (I-t) andcapacitance-frequency (C-f) analysis were performed on films. All ofthe films exhibita low leakage current, a high breakdown field strength (3MV/cm-4.5MV/cm), and high dielectric constant (20-30). From the temperature dependence of leakage current,we can conclude that the dominant conduction mechanism is ascribed toSchottky emission at high electric field (>1MV/cm) and hopping conduction at lowelectric field (<1MV/cm). According to our results, the oxide plasma surfacetreatmenton as-deposited $BaTa_2O_6$ resulted in lowering interfacebarrier height and thus, leakage current when a negative voltage applied to the A1 electrode. This can be explained by reduction of surface contamination via etching surface and filling defects such as oxygen vacancies.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권11호
• /
• pp.483-489
• /
• 2005

This study performs a simulation for an accumulation mechanism of contaminants, which were produced in an industrial belt of inland, on the surface of insulators. From the simulation, silicon insulators presented higher accumulation than that of EPDM(Ethylene Propylene Diene Terpolymer : EPDM) insulators on the same distance in the case of the Virgin polymer insulator, and this result presented the same result in the insulator applied in actual fields. In the case of the accumulation test for the Virgin insulator and insulators used in actual fields, it is evident that the Virgin insulator presented more accumulation than that of the insulator used in actual fields. The results can be caused by the generation of LMW (Low Molecular Weight) on the external material of polymer insulators, and the level of the accumulation can be changed according to the degree of the continuous generation of LMW. In order to simulate a certain pollution of an industrial belt, which is located along the coastline, leakage currents were measured by applying the contaminant compulsively that was produced with salts and Kaolin according to the ratio of its weight on the surface of insulators. The more increase in the content of Kaolin pollution, the level of leakage currents on the surface of polymer insulator more increased. In addition, the approaching time to the maximum value of leakage currents presented a nearly constant level regardless of the content of Kaolin. The level of leakage currents significantly decreased according to the passage of time, and the level of leakage currents on the surface maintained a constant level at a specific time regardless of the content of Kaolin.

• 대한기계학회논문집B
• /
• 제29권8호
• /
• pp.948-955
• /
• 2005

A three-dimensional computation was conducted to understand effects of the inlet boundary layer thickness on the internal flow in a low-speed axial compressor operating at the design condition($\phi=85\%$) and near stall condition($\phi=65\%$). At the design condition, the flows in the axial compressor show, independent of the inlet boundary layer thickness, similar characteristics such as the pressure distribution, size of the hub comer-stall, tip leakage flow trajectory, limiting streamlines on the blade suction surface, etc. However, as the load is increased, the hub corner-stall grows to make a large separation region at the junction of the hub and suction surface for the inlet condition with thick boundary layers at the hub and casing. Moreover, the tip leakage flow is more vortical than that observed in case of the thin inlet boundary layer and has the critical point where the trajectory of the tip leakage flow is abruptly turned into the downstream. For the inlet condition with thin boundary layers, the hub corner-stall is diminished so it is indistinguishable from the wake. The tip leakage flow leans to the leading edge more than at the design condition but has no critical point. In addition to these, the severe reverse flow, induced by both boundary layer on the blade surface and the tip leakage flow, can be found to act as the blockage of flows near the casing, resulting in heavy loss.

• 한국전기전자재료학회논문지
• /
• 제21권7호
• /
• pp.652-659
• /
• 2008

The nonlinear electrical properties and aging characteristics against surge stress of ZPCCL-based varistors were investigated for different sintering temperatures of the range $1240-1300^{\circ}C$. As the sintering temperature increased, the varistor voltage decreased from 732.2 to 53.8 V/mm, the nonlinear exponent decreased from 58.5 to 4.1, and the leakage current increased from $0.38{\mu}A$ to $46.5{\mu}A$. The varistors sintered at $1250^{\circ}C$ and $1260^{\circ}C$ exhibited the high stability against multiple surge, $150A/cm^2(8{\times}20{\mu}s)$. On the whole, the variation rate of electrical characteristics against impulse current stress was gradually increased in order of varistor voltage$\rightarrow$nonlinear exponent$\rightarrow$dissipation facto$\rightarrow$leakage current.

• 전기학회논문지
• /
• 제60권6호
• /
• pp.1175-1177
• /
• 2011

The SBN thin films were deposited on Pt/Ti/$SiO_2$/Si and p-type Si(100) substrate by rf magnetron sputtering method using $Sr_{0.7}Bi_{2.3}Nb_2O_9$ ceramic target. SBN thin films deposited were annealed at 600~800[$^{\circ}C$] by furnace in oxygen atmosphere during 40min. The polarization characteristics have been investigated to confirm the possibility of the SBN thin films for the application to destructive read out ferroelectric random access memory. The maximum remanent polarization and the coercive voltage are 0.6[${\mu}C/cm^2$], 1.2[V] respectively at annealing temperature of 800[$^{\circ}C$]. The leakage current density was the $2.57{\times}10^{-6}[A/cm^2]$ at an applied voltage of 5[V] at annealing temperature of 650[$^{\circ}C$]. Also, the fatigue characteristics of SBN thin films did not change up to $10^8$ switching cycles.