• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.6A
• /
• pp.417-424
• /
• 2011

This study focused on development of 60 m span PSC girder considering not only structural performance, but also economical efficiency and constructability including from the improvement of cross-section to the tendon profiles in sequence. Bulb-T type cross section was derived from optimization and actual possibilities to design a bridge were assessed through cross section evaluation. Tendons were also arranged efficiently so that the girder could resist the service load effectively. After developed girder was applied to a sample bridge, result of finite element analysis proved all load steps were satisfied with the allowable stress. Furthermore, it seemed that sufficient redundancy will be available to design a bridge safely. Based on these, a full-scale 60 m span girder was fabricated and 4 point bending test was performed. An initial crack occurred over twice of the service load in this experiment, which establishes adequate structural performance. 60 m span Half-Decked PSC girder developed in this study has a lower height for the given span which resulted from cross section improvement and efficient tendon layout. This girder also has not only the structural advantage, but also advantages in economical efficiency and constructability.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.6
• /
• pp.637-658
• /
• 2022

TBM tunnel is simple with the iterative process of excavating the ground, building a segment ring-build, and backfilling. Drill & Blast, a conventional tunnel construction method, is more complicated than the TBM tunnel and has some restrictions because it repeats the inspection, drilling, charging, blasting, ventilation, muck treatment, and installation of support materials. However, the preparation work for excavation requires time and cost based on a very detailed plan compared to Drill & Blasting, which reinforces the ground and forms a tunnel after the formation of tunnel portal. This is because the TBM equipment for excavating the target ground determines the success or failure of the construction. If the TBM, an expensive order-made equipment, is incorrectly configured at the assembly stage, it becomes difficult to excavate from the initial stage as well as the main excavation stage. When the assembled shield TBM equipment is dismantled again, and a situation of re-assembly occurs, it is difficult throughout the construction period due to economic loss as well as time. Therefore, in this study, the layout and plan of the site and the assembly process for each major part of the TBM equipment were reviewed for the assembly of slurry shield TBM to construct the largest diameter road tunnel in domestic passing through the Han River and minimized interference with other processes and the efficiency of cutter head assembly and transport were analyzed and improved to suit the site conditions.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.19 no.2
• /
• pp.151-158
• /
• 2016

Tidal farm is a multi-arrayed turbine system for utilizing tidal stream energy. For horizontal-axis turbine(HAT) system, it is recommended that each unit has to be deployed far apart in order to avoid hydrodynamic interference among turbines, as proposed by the European Marine Energy Centre(EMEC). But there is no rule for the arrangement of vertical-axis turbine(VAT) yet. Moreover it has been reported that a proper arrangement of adjacent turbines can enhance the overall efficiency even greater than an arrangement without mutual interference effect. This paper suggests the layout of VATs showing the better performances, which turned out to be quite different from HATs' arrangement. Numerical calculations were performed to investigate the performance variation in terms of the rotational direction as well as the distance between turbines. It has been shown that the best combination of rotational direction and distance between turbines can increase its performance higher about 9.2% than that of two independently operated turbines. It is likely that such improvement is due to the increased velocity between adjacent turbines. For diagonally arranged turbines, the maximum normalized mean power coefficient was obtained to be higher about 5.6% than that of two independent turbines. It is expected that the present results can be utilized for conceptual design of tidal farm to harness the tidal stream energy.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.37 no.5
• /
• pp.915-926
• /
• 2017

The subway is the transportation means most commonly used by the citizens of the metropolitan area along with the buses in the metropolitan area and major metropolitan municipalities. However, satisfaction with the signboards is low and the signboards need to be improved. In this study, we investigated the problem of guide signs of city hall and exchange area with L - shaped history structure for guide signs affecting route finding. As a result, it is necessary to confirm whether the moving distance is long and moving accurately to the desired destination due to the L - shaped historical structure in both the station and the alternate area. In both stations, the number of the guide signs, Problems such as installation position, height, other. In this study, the movement within the subway station is classified according to the space. The type of guide sign installation was defined, and the specific principles for guiding the movement route were proposed. This research is expected to be useful as an important basic data for the types and layout of subway stations.

• Archives of design research
• /
• v.11 no.1
• /
• pp.11-20
• /
• 1998

Display in commercial space is one of the most important fields in modem advanced industrial sectors as means of promoting the volume of sales. Additionally, consummers' preferences are more complicated and various than before because of improvement of quality of life. In order to satisfy the various comsumer's desire, the role of display must be an important factor in commercial space. On the other hand, the facade of commercial buildings in the concept of visual merchandising has important effect on the commercial space such as layout of a shop, setting up presentation space, and visual expression. The structure of the facade of the store provides not only an advertising function but also an important position to the composition of external space. Besides, enterance space is a part of a store, and it is closely related to outdoor space. Therefore, the relationship between a store and outdoor space should be carefully considered in terms of functional and expressional problems.This study introduces all sort of characteristics of the facade of enterance speac in the commercial buildings. It also investigates the relationship among the characteristics. Moreover, it analyzes the effect of facade style on shop environment such as zonning, inducement plan, and allocation plan. For the purpose of this study, 57 fashion stores, located in Myung-Dong(Seoul), are investigated. Based on the sample, this study analyzes the relationship between the facade style and visual presentation. Finally, it suggests the desirable direction of space composition based upon the concept of visual merchandising.

• Journal of Families and Better Life
• /
• v.26 no.2
• /
• pp.115-127
• /
• 2008

The purpose of this study was to examine the characteristics of change in the composition of indoor spaces in Korean-style houses which have been repaired and improved extensively through the 'Bukchon Improvement Project' and are being utilized for public purposes. For this, we conducted a field survey through visiting the house sites from the 5th to the 26th of May, 2006. Conclusions drawn from this study are as follows. Bukchon Korean-style houses maintain centripetal space composition, in which the rooms surround the court. Centering on the court, the hierarchy of spaces is determined, and the hierarchy of spaces and the composition of internal layout are restructured centering on the court and the main hall without change in direction and position. The main hall is sometimes converted to a room, but it maintains an open space relation with other spaces centering on the court, and therefore, even after its use has been changed, it is still the most Korean-style space. In addition, with floor heating, the common sitting-style life is maintained continuously although the rooms have been converted and standing-style furniture is used. In this way, publicly promoted policies for Korean-style houses are allowed within the limit that the appearance is maintained and the internal spaces do not change the overall structure. However, in order to maintain the tradition of Korean-style houses and utilize them as various spaces, the following supplementations are necessary. First, the main hall and the inner court of a Koreanstyle house should be utilized actively. The court sometimes keeps individuals' privacy or expands the space by extending the view to outdoor spaces, and is sometimes used as an open space through interconnection between the inside and the outside of the house. Second, consideration should be given to vertical spaces. Horizontal expansion causes a change of floor plan. Thus, space should be secured using various cross-sectional changes, such as a kitchen and a loft over the kitchen. Third, structure should be changeable in order to adjust the size of spaces. Thus, through research on traditional windows, we need to develop changeable walls that can be installed and removed easily according to the use of spaces.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.41 no.6
• /
• pp.54-63
• /
• 1999

Considering that rural village had evolved through a long-sustained effort of harmnization with nature, there should be the wisdom not only to reflect the level of rural resident's housing demand, but also to conserve the traditional characteristics of high-valuation in the modern rural housing. In Korea , standard design proposals of rural houses had been made public three times ; in 1972 , 1984 and 1995. so , firstly, this study analysed the inner-space layouts of design proposals mentioned above, from which changes and problems in the past housing design were derived. And also, through, the positive acceptance of residents' opinion living inthe houses built by standard design proposals in 1970 ~1980's, improved design principles and an alternative model were proposed , finally. The inner-space structed of standard design proposals in 1970s was originated from small-scaled and low-priced one, basically under the " open system". In 1980s, the basic design principle changed to the 'closed system' in which the living room being the focus of indoor family life, and , in 1990s, progressively, therural housing developed to the high qualified type by the spatial enlargement and with increased equipements. However, this structural change of rural house brought about the problem of functional separatioon between farming and daily living activities. In details, limited spaces of multipurpose spaces and sanitary facility would be mentioned as problems for improvement. conclusively in this study, newoly arranged "open system" was recommended , as a basic design principle for theinner space structure formation of rural house, which easily links the constituent inner-house spaces to outer one. Based on this principle, the detailed design criterial was proposed as follows ; 1. The living room be directly linked to the front-yard and centrally placed, the addtional space of which could be secured for the special family events by the flexibleuse of its adjacent room or by the housing of male quarters(separated from main building quarter). 2. The kitchen also be directly linked to side-yard and to livng room , for the convenience of farming activities and the shortening of path flow housewife. 3. The expanded toilet-and-bathroom be placed in the directly connected left-hand side to the living room and also be allowed access through multipurpose spaces to out door. 4. The multipurpose spaces be directly connected to the kitchen and the toilet and-bathroom , of which function would be for undressing of working clothes, quickwashing and ordinary working.nd ordinary working.

• Asian Journal of Turfgrass Science
• /
• v.12 no.1
• /
• pp.49-78
• /
• 1998

Nowadays, there are increasing demands of golf courses and it is necessary to make more golf courses than the present. To do this, we need to improve the environmental problems with the regional inhabitants, and it is said that the first thing to be considered in developing any golf course in Korea is to preserve the environment. In this context, the purpose of this study is to set forth several design factors to lessen the negative impacts which are accompanied with the development of golf courses. 1. The present conditions of golf courses in Korea Many new golf courses have come into being, particularly since the late 1980s, and now, in the year of 1997, over one hundred of golf courses are doing their business, yet the number of golf course is still less than required. So far, over a half of them have been made in the vicinity of Seoul on account of various reasons, and this has adversely affected on our natural environment. This unreasonable development of golf courses has caused serious water pollution, landslides and the other problems. Also, the topography of Korea is not good for golf courses. Although the demands of golf courses are increasing, the suitable sites for them are very limited, and therefore it is sometimes unavoidable to make golf courses on steep hills. Consequently, in designing golf courses in Korea, the most important thing is the balance between natural environment and artificial environment. 2.Eco-friendly golf course design factors 1) The concept of eco-friendly golf courses Ecologically sustainable and sound golf courses which are made by eco-friendly approaches 2)Basic conditions of eco-friendly golf courses (1)The most suitable sites (2) Conservation of existing ground as much as possible (3)Proper use of agricultural chemicals which have great impacts on the environment (4) Reasonable use of fertilizers (5) Developing a specialized fertilizer only for grass (6) Adaptation of organic agriculture (7) Improvement of grass sorts (8) Establishing reservoirs for purifying the water from golf courses 3) Eco-friendly golf courses (1) Location-Enough area /Gentle slope/Winding ground/Including lakes or streams /Not crossing wind's main direction Facing south or southeast /Suitable soIl for grass /Good drainage /Low level of underground water (2)Course layout and design -Consideration about existing contours as much as possible -Adaptation of Scotish design trend -Various holes' configuration -Consideration toward surrounding landscapes -Reducing grass areas -Giving buffer zones -Adapting computer methods in the process of site analysis and design (3) Eco-friendly considerations in constructing and managing golf courses -Protection of wildlife -Reuse of existing forests and preservation of topsoil -Renovation of old-fashioned courses -Reducing grass areas -Purification of water -Standization of management -Strict regulations against chemicals -Recycling organic materials -Through separation of the water inside golf courses and out of bounds -Getting proper construction works done in a due time 4.Eco-friendly considerations from a viewpoint of cultural environment 1) Well-matched landscape design and events planning 2) Implement of identifications and awarding systerns 3)Acknowledgement of superintendents' qualitications in the maintenance of golf courses 4)Increasing public golf courses and keeping good relationships with the neighbors near golf courses Key words: Pro-environmental development, Golf course.

• Archives of design research
• /
• v.17 no.1
• /
• pp.373-382
• /
• 2004

Large sized buildings have proliferated in the modern world in order to solve problems caused by the growth of cities, and this trend has lead to diversity in style and utilization of interiors. In particular, wayfinding within the shopping mall for a customer is a common problem, so if customers do not have to face these navigational problems and could find the way more easily, then shopping mall or the store can expect much better profits. Therefore, directional sign system that can provide accurate and speedy information for customers with diversified ages, gender and knowledge is necessary. Firstly, the definition and element of all directional sign are analyzed through the existing literature survey. The elements are based on the practical elements and six categories such as type, pictogram, color, layout, form, and location were considered. Secondly, directional signs in large underground shopping mall was considered, and the speciality of the underground shopping mall was investigated, and finally top three underground shopping malls was analyzed. Thirdly, through the questionnaire, an objective appraisal of directional signs and problems was developed, and following possible improvement was suggested. This study has its own limitations since it is only applicable to the specific locations, however, directional designs will be useful in other types of buildings as well. Through the continuous studies of the users' psychology, these kinds of studies will be related to the environmental characteristics of various places.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.7
• /
• pp.310-316
• /
• 2019

In automotive application, customers are demanding high efficiency and various functions for convenience. The demand for these automotive applications is steadily increasing. In this study, it has been studied the analysis of heat flow to improve the PCB(printed circuit board) heating performance of WPC (wireless power charger) recently developed for convenience. The charging performance of the wireless charger has been reduced due to power dissipation and thermal resistance of PCB. Therefore, it has been proposed optimal PCB design, layout and position of electronic parts through the simulation of heat flow analysis and PCB design was analyzed and decided at each design stage. Then, the experimental test is performed to verify the consistency of the analysis results under actual environmental conditions. In this paper, The PCB modeling and heat flow simulation in transient response were performed using HyperLynx Thermal and FloTHERM. In addition, the measurement was performed using infrared thermal imaging camera and used to verify the analysis results. In the final comparison, the error between analysis and experiment was found to be less than 10 % and the heating performance of PCB was also improved.