• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.5
• /
• pp.369-378
• /
• 2003

This paper presents design and VLSI implementations of a reassembly processor for ATM/AAL. The assembly processor is responsible for processing ATM cells from the receive physical interface. It controls the transfer of the AAL payload to host memory and performs all necessary SAR and CPCS checks. We propose the improved structure of cell identification algorithm and smart scatter method for host memory management. The proposed cell identification algorithm quickly locates the appropriate reassembly VC table based on the received VPI./VCI channel value in the ATM header. The cell identification algorithm also allow complete freedom in assignment of VCI/VPI values. The reassembly processor uses a smart scatter method to write cell payload data to host memory. It maintains the scatter operation and controls the incoming DMA block during scatter DMA to host memory. The proposed reassembly processor can perform reassembly checks on AAL. OAM cell. For an AAL5 connection, only CPCS checks, including the CRC32, are performed. In this paper, we proposed a practical reassembly architecture. The design of reassembly processor has become feasible using 0.6${\mu}{\textrm}{m}$ CMOS gate array technology.

• Archives of Craniofacial Surgery
• /
• v.13 no.1
• /
• pp.46-49
• /
• 2012

Purpose: The forehead flap is the workhorse in nasal reconstruction, which provides a similar skin color, texture, structure, and reliability. There are some disadvantages, including donor site morbidities, 2- or 3-stage operations, and postoperative management after initial flap transfer. Furthermore, there has been little attention to the exposed raw surface wound, after the first stage of an operation. This article describes the authors' modification to overcome this problem, using artificial collagen membrane. Methods: An Artificial collagen membrane is composed of an outer silicone membrane and an inner collagen layer. After a forehead flap elevation, the expected raw surface was covered by an artificial collagen membrane with 5-0 nylon suture. A simple dressing, which had been applied to the site, was changed every 2 or 3 days in an outpatient unit. At 3 weeks postprocedure, a second stage operation was performed. Results: With biosynthetic protection of the raw surface, there were no wound problems, such as infection or flap loss. Thus, the patient was satisfied due to an effortless management of the wound and a reduction in pain. Conclusion: The application of an artificial collagen membrane to the raw under-surface of the flap could be a comfortable and a protective choice for this procedure.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.545-553
• /
• 2009

A lot of long-span marine bridge, which connects land to island or island to island, are being designed and constructed lately in south-west coast in South Korea. In the past, caisson foundations in marine were mainly adopted in construction and stability aspect, however, nowadays with development of pile construction technology, drilled shaft foundations are mainly adopted. As the long span cable stayed bridge and suspension bridge applied with lots of loads are being designed, the scale of pile foundations are getting larger. As the construction cost of substructure including foundation in marine bridges is too high, the appropriate evaluation of the axial bearing capacity of pile becomes a core factor to decide the construction cost of foundation if the drilled shaft is adopted as foundation type of bridge. The evaluation values of skin friction and end bearing capacity of drilled shaft in weathered rock suggested in south Korea are only to introduce the foreign specifications, and most of them are designed in a kind of hard soil layer. Also the allowable load of pile section is less than the expected bearing capacity of pile in the soil condition since the allowable capacity of pile is undervalued. Recently in order to improve this factor the bi-axial hydraulic load test of pile was taken, the data of load transfer analysis of pile, unit of skin friction and end bearing capacity are accumulated. In our country, the design of piles are made with ASD, however, LRFD considering service, strength and extreme state was adopted in Incheon Grand Bridge implemented with BTL, and the research to systematize the resistance coefficient appropriate at home country are being progressed.

• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.1
• /
• pp.28-38
• /
• 2014

The organic-inorganic composite membrane in polymer exchange membrane fuel cells (PEMFCs) have several fascinating technological advantages such as a proton conductivity, thermal stability and mechanical properties. As the inorganic filler, silicon carbide (SiC) fiber have been used in various fields due to its unique properties such as thermal stability, conductivity, and tensile strength. In this study, composite membrane was successfully fabricated by modified-silicon carbide fiber. Modified process, as a novel process in SiC, takes reaction by phosphoric acid after oxidation process (generated homogeniusly $SiO_2$ layer on SiC fiber). The mechanical property which was conducted by tensile test of the 5wt% modified-$SiO_2@SiCf$ composite membrane was better than that of Aquivion casting membrane as well as ion cxchange capacity(IEC) and proton conductivity. In addition, the single cell performance was observed that the 5wt% modified-$SiO_2@SiCf$ composite membrane was approximately $0.2A/cm^2$ higher than that of a Aquivion casting electrolyte membrane and electrochemical impedance was improved with the charge transfer resistance and membrane resistance.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.05a
• /
• pp.77-80
• /
• 2017

One of the fundamental limits of Bluetooth Low Energy(BLE) is that the data transmission is available via singlehop connection. In this research, we suggested the stable multihop transmission method to overcome this limitation. In multihop connection situation, multiple singlehop connection should be made and disconnected dynamically. Therefore, we stored the data within the GATT layer and tried to send it dynamically. We divided whole process as 4 states, and let each nodes transfers around each states to make data connection safely. Also, we set the transfer policy between each states during the transmission to make a robust system. From the experiment in real-time environment, we proved that our method showed high rate of packet delivery in a multihop network, which consists of more than 3 nodes.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.5
• /
• pp.410-420
• /
• 2015

This paper provides a comparison of power converter loss and thermal description for voltage source and current source type 5 MW-class medium-voltage topologies of wind turbines. Neutral-point clamped three-level converter is adopted for a voltage source type topology, whereas a two-level converter is employed for current source type topology, considering the popularity in the industry. To match the required voltage level of 4160 V with the same switching device of IGCT as in the voltage source converter, two active switches are connected in series for the case of current source converter. Transient thermal modeling of a four-layer Foster network for heat transfer is done to better estimate the transient junction and case temperature of power semiconductors during various operating conditions in wind turbines. The loss analysis is confirmed through PLECS simulations. Comparison result shows that the VSC-based wind turbine system has higher efficiency than the CSC under the rated operating conditions.

• Composites Research
• /
• v.33 no.2
• /
• pp.61-67
• /
• 2020

Preforming is crucial in resin transfer molding process using woven fabric. When shear deformation exceeds the locking angle, wrinkles are generated in the preform, which causes defects in the RTM process. Therefore, in this study, the allowable shear deformation limit of carbon fiber woven fabrics is quantified and the molding characteristics are verified using the actual fabric forming. As a result, the characteristics of creases according to the layer setups have been examined and the results have been discussed. Numerical analyses have been also performed using measured shear properties. These results have been compared with the experimental results.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.5
• /
• pp.577-582
• /
• 2015

This paper is the fundamental study for the application of cold storage system to the transportation equipment by sea and land. This numerical study presents the solid-liquid phase change phenomenon of calcium chloride solution of 30wt %. The governing equations are 1-dimensional unsteady state heat transfer equations of $1^{st}$ order partial differential equations. This type of latent heat storage material is often usable in fishery vessel for controlling the temperature of container with constant condition. The governing equation was discretized with finite difference method and the program was composed with Mathcad program. The main parameters of this solution were the initial temperature of heat storage material, ambient temperature of cold air and the velocity of cold air. The data of boundary layer thickness becomes thin with the increasing of cold air flowing velocity and also the heat storage completion time become shorten.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.7
• /
• pp.462-469
• /
• 2008

A regenerative evaporative cooler has been fabricated and tested for the evaluation of cooling performance. The regenerative evaporative cooler is a kind of indirect evaporative cooler comprised of multiple pairs of dry and wet channels. The air flowing through the dry channels is cooled without any change in the humidity and at the outlet of the dry channel a part of air is redirected to the wet channel where the evaporative cooling takes place. The regenerative evaporative cooler fabricated in this study consists of the multiple pairs of finned channels in counterflow arrangement. The fins and heat transfer plates were made of aluminum and brazed for good thermal connection. Thin porous layer coating was applied to the internal surface of the wet channel to improve surface wettability. The regenerative evaporative cooler was placed in a climate chamber and tested at various operation condition. The cooling performance is found greatly influenced by the evaporation water flow rate. To improve the cooling performance, the evaporation water flow rate needs to be minimized as far as the even distribution of the evaporation water is secured. At the inlet condition of $32^{\circ}C$ and 50%RH, the outlet temperature was measured at $22^{\circ}C$ which is well below the inlet wet-bulb temperature of $23.7^{\circ}C$.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1997.11a
• /
• pp.10-11
• /
• 1997

고체 추진제를 사용하는 추진 시스템을 개발하는데 가장 커다란 문제로 인식되고 있는 것은 추진제의 연소 특성을 이해하는 일이다. 그 중에서도 연소실의 압력 진동과 추진제 벽면으로 흡수되는 복사 열전달에 의한 연소율(burning rate)의 변화로 인하여 발생하는 연소 불안정에 대한 이해는 아직도 완전히 규명되지 않고 있다. 고체 추진제의 연소 불안정에 대한 이론적 해석은 준-정상 1차원 해석(Quasi-Steady Homogeneous One-Dimension) 방법에 의하여 단순화된 지배방정식을 해석하는 것이 일반적으로 잘 알려져 있는 방법이다. 이 가정은 고체 추진제가 연수되는 영역을 두께가 매우 얇은 영역의 표면반응영역(surface reaction layer)과 화학반응이 없는 응축상태영역(condensed phase zone) 그리고 기체상태의 연료와 화염이 존재하는 기체상태영역(gas phase zone) 등의 3영역으로 구분하며, 기체상태영역에서 발생하는 교란에 대한 응축상태영역의 반응시간 크기(response time scale)가 매우 크기 때문에 응축상태영역의 반응은 준 정상적으로 일어난다고 가정하는 것이다.그러나, 연소실의 온도가 $3000^{\circ}K$ 정도의 높은 온도이어서 복사 열전달에 의한 고체 추진제의 가열이 중요한 열전달 방법으로 작용하게 되므로 이를 무시한 이론적 해석은 물리적인 중요성이 약하여질 수밖에 없다. 본 연구에서는 기체영역으로부터 전달되는 복사 열전달은 투명(transparent)한 표면반응영역을 통과하여 응축상태영역에서 모두 흡수되며 추진제 표면에서의 복사열방출(emission)을 고려하였다. 또한 연소불안정 현상을 해석하기 위하여 표면반응영역에서의 경계조건은 선형교란량으로 대치하는 Zn(Zeldovich-Novozhilov) 방법을 사용하였다. 이 방법은 기체상태영역에 대한 구체적인 해석없이도 연소불안정 현상을 해석할 수 있는 장점이 잇다. 즉 응축상태영역에서의 연소율과 표면온도는 각각 기체영역으로부터 전달되는 온도구배와 연소압력, 그리고 복사 열전달의 함수관계이므로 선형교란에 의한 추진제표면에서의 교란경계조건을 얻을 수 잇으며, 응축영역의 교란지배방정식과 함께 사용하여 압력교란과 복사 열전달의 교란에 대한 연소율의 교란 증감 여부를 판단하여 연소 불안정 현상을 해석할 수 있다.