• 한국위성정보통신학회논문지
• /
• 제5권1호
• /
• pp.69-74
• /
• 2010

통신해양기상위성 개발 과정의 일환으로 통신해양기상위성이 아리안-5ECA 발사체에 탑재되어 발사될 때 발생되는 음향하중으로 부터 안전한가를 검증하기 위하여 음향진동 시험이 수행되었다. 본 논문에서는 통신해양기상위성개발 과정에서 수행된 음향진동시험과 관련하여 시험 준비 과정을 설명하고, 시험 결과에 대한 검토를 통하여 통신해양기상위성이 발사 시 경험하게 되는 음향하중에 대하여 안전한지 검토하였다. 태양전지판, Ka Band 통신탑재체 안테나 및 피드, 해양탑재체, 기상탑재체 등에 대한 상세한 검토를 통하여 통신해양기상위성이 발사 시 음향하중으로부터 안전하다는 것을 확인하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.957-961
• /
• 2005

A satellite component must withstand vibration caused when launch vehicle acoustics and engine rumble transfer to it through its structural mount. Components shall be subjected to environmental tests after manufacturing process thus the environmental test conditions are needed for component level test including vibration and shock. This paper deals with derivation of component-level environmental test specifications, especially for solar panels of STSAT-2(Science & Technology SATellite-2). Sine sweep random vibration, and shock test conditions were generated for solar panels by assuming the satellite as single-degree-of-freedom system with a base excitation.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.242-245
• /
• 2006

This paper is an assessment on the dynamic test results of optical bench for LEO satellite. According to the design requirements, optical bench was designed and manufactured. Dynamic test was performed to verify stability of optical bench. Low level random vibration test, sine burst test and sine vibration test are carried out to identify dynamic characteristics and to verify static strength and safety under quasi-static load conditions. From the result it can be stated that the optical bench is well qualified under the launch environmental conditions.

• 한국정밀공학회지
• /
• 제21권8호
• /
• pp.120-128
• /
• 2004

The impulse between launch vehicle and atmosphere can generate a lot of noise and vibration during the process of launching a satellite. Structurally, the electronic equipment of a satellite consists of an aluminum case containing PCB. Each PCB has resistors and IC. Noise and vibration of the wide frequency band are transferred to the inside of fairing, subsequently creating vibration of the electronic equipment of the satellite. In this situation, random vibration can cause malfunctioning of the electronic equipment of the device. Furthermore, when the frequency of random vibration meets with natural frequency of PCB, fatigue fracture may occur in the part of solder joint. The launching environment, thus, needs to be carefully considered when designing the electronic equipment of a satellite. In general, the safety of the electronic equipment is supposed to be related to the natural frequency, shapes of mode and dynamic deflection of PCB in the electronic equipment. Structural vibration analysis of PCB and its electronic components can be performed using either FEM or vibration test. In this study, the natural frequency and dynamic deflection of PCB are measured by FEM, and the safety of the electronic components of PCB is evaluated according to the results. This study presents a unique method for finite element modeling and analysis of PCB and its electronic components. The results of FEA are verified by vibration test. The method proposed herein may be applicable to various designs ranging from the electronic equipments of a satellite to home electronics.

• 한국항공우주학회지
• /
• 제32권9호
• /
• pp.103-113
• /
• 2004

위성은 조립 및 시험 완료 후 운반 및 발사 순간부터 임무 궤도로 진입할 때까지 발사체에 의한 정하중, 동하중 및 충격하중을 겪게 되며, 임무궤도에서 열진공, 복사 및 미세중력 환경하에 놓이게 되어 위성의 설계, 제작, 조립 및 시험 시 이들 발사환경과 우주환경을 고려하여 개발을 수행하여야 한다. 본 논문에서는 HAUSAT-1 피코위성의 구조 열해석과 설계 결과를 논의하고, 발사 과정과 우주에서 겪게 되는 환경을 모사한 발사환경 및 우주환경시험의 결과를 논의한다. HAUSAT-1 위성의 기계시스템은 인증 수준의 진동시험과 열진공시험 후에도 안정하다는 것을 확인하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.363-366
• /
• 2006

In general, pyrotechnic shock or pyroshock is generated during the operation of separation devices, which use explosives, such as pyrobolt, puronut, purocutter, linear shape charge, and so on. During the flight of launch vehicle, pyroshock is mainly produced at the events of satellite separation, fairing separation and stage separation. In this paper, characteristics of pyroshock are introduced in the first place and measured shock result data at the UMR of satellite mock-up during the separation tests of satellite and fairing are suggested. These results are compared with the suggested pyroshock test specification of satellite, and it finally confirms that the specification is reasonable for the qualification of satellite against pyroshock.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.172-175
• /
• 2005

Since, similar to other commercial launch vehicles, various kinds of pyrotechnique devices are used in the KSLV-I(Korea Space Launch Vehicle), the electronic equipment on the vehicle equipment bay is exposed to the sever pyroshock environment during Pyrotechnique device detonation. In order to confirm the survivability of electrical instruments from these pyroshock conditions, shock tests are performed by using a pyroshock simulation during development and qualification phase. In this paper, the pyroshock simulator installed in KARI(Korea Aerospace Research Institute) are briefly introduced, and its performance of pyroshock generating is compared with the measured shock response spectrums from small scaled fairing jettisoning tests. The results show that the pyroshock simulator is still proper to generate severe pyroshocks similar to real pyrotechique detonating conditions, but the redesign on the test jigs is necessary to improve its test performance.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.949-952
• /
• 2005

According to the national space program in Korea, is satellites will be launch into space up to 2015. Especially, KARI is going to develope of its own a high resolution camera of less than 1m to be mounted on next Multipurpose Satellite. When performing testing of large spacecraft or hardware that will be launched into orbit, it is necessary to conduct a testing with space-simulated environment. To achieve this requirement, thermal vacuum chamber is generally used. KARI has been developed a very Large Thermal Vacuum Chamber(LTVC) from 2003 to accomodate future space program, such as KOMPSAT, COMS, and Launch vehicles. This new facility will be used to qualify the first self developed High Resolution Camera, which will be loaded on KOMPSAT-3. To perform an optical test for space camera, it is necessary to provide vibration free environment. Thus the vibration responses on the optical table due to external vibration should be minimized by using a special isolation system. In this paper, we propose the concept design of vibration isolation system for the development of the high resolution camera.

• 한국항공우주학회지
• /
• 제33권11호
• /
• pp.95-105
• /
• 2005

우주시스템연구실에서는 2008년 발사 예정으로 나노위성인 HAUSAT-2를 개발하고 있다. HAUSAT-2 구조-열 모델(STM)은 구조 및 열적 설계마진을 검증하기 위하여 개발한 시스템 모델이다. HAUSAT-2의 구조-열 모델을 이용하여 인증 수준의 진동시험과 열진공/평형시험을 수행하였다. 본 논문에서는 구조-열 모델의 구조해석과 진동시험의 결과를 비교하였고 이를 통해 해석조건을 변경해 재해석을 수행하였다. 인증수준의 진동시험 결과 구조-열 모델은 구조적인 손상 없이 설계 강성 요구조건을 만족하는 것을 확인하였다. 또한 구조 조립을 통해 조립성과 인터페이스를 확인하였다.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권4호
• /
• pp.551-564
• /
• 2016

High-speed flight vehicles (HSFVs) such as space launch vehicles and missiles undergo severe dynamic loads which are generated during the launch and in in-flight environments. A typical vehicle is composed of thin plate skin structures with high-performance electronic units sensitive to such vibratory loads. Such lightweight structures are then exposed to external dynamic loads which consist of random vibration, shock, and acoustic loads created under the operating environment. Three types of dynamic loads (acoustic loads, rocket motor self-induced excitation loads and aerodynamic fluctuating pressure loads) are considered as major components in this study. The estimation results are compared to the design specification (MIL-STD-810) to check the appropriateness. The objective of this paper is to study an estimation methodology which helps to establish design specification for the dynamic loads acting on both vehicle and electronic units at arbitrary locations inside the vehicle.