• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.5
• /
• pp.401-407
• /
• 2017

This paper describes wavenumber filtering for damage detection using single-frequency standing wave excitation and laser scanning sensing. An embedded piezoelectric sensor generates ultrasonic standing waves, and the responses are measured using a laser Doppler vibrometer and mirror tilting device. After scanning, newly developed damage detection techniques based on wavenumber filtering are applied to the full standing wave field. To demonstrate the performance of the proposed techniques, several experiments were performed on composite plates with delamination and aluminum plates with corrosion damage. The results demonstrated that the developed techniques could be applied to various structures to localize the damage, with the potential to improve the damage detection capability at a high interrogation speed.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.4
• /
• pp.79-86
• /
• 1999

Electronic Speckle Pattern Interferometry(ESPI) is a powerful tool to measure the vibration mode shape and resonance frequency for modal analysis. As for ESPI this method is very suited for full-field measurement of objects in industrial areas because the interferograms are recorded with a video camera and evaluated in real-time with a computer. In this study We performed experiments at the same constraint conditions as disk brake of the practical vehicle as far as possible and obtained the resonance frequencies and vibration mode shapes by using time-averaged ESPI at once. Finally to assure the expetimental results by time-averaged ESPI we also compare those with results obtained by Laser Doppler Vibrometer and obtained good agreement.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.5
• /
• pp.315-320
• /
• 2000

This paper presents the fabrication and test of a micropump with an electromagnetic actuator and a pair of aluminum flap valves. The actuator consists of a solenoid coil, a permanent magnet and an actuator diaphragm. The actuator diaphragm is fabricated by the spin coating of silicone rubber. The valve are passive ones and are fabricated by micromachining. The deflection of the fabricated actuator diaphragm is measured with a laser vibrometer. The deflection of the actuator diaphragm is proportional to the input current. The measured deflection of the fabricated diaphragm is $400 \mum$,/TEX> when the input is 118 mApp, and the cut-off frequency is 50 Hz. The maximum flow rate of the fabricated micropump with the electromagnetic actuator is about 5$0 \muell/min$ at 5 Hz when the input current and the duty ratio of the square was are 118 mApp and 50%, respectively.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.370-375
• /
• 2009

The purpose of this study is to reduce the vibration of the computer by developing the vibration absorber and damper. The eccentricity of the cooling fan causes the vibration of the computer. We designed the material properties of the vibration absorber by FEM model within operation frequencies of the cooling fan. We experiment the overall analysis and system analysis. The vibration of cooling fan is measured by using a laser vibrometer. The result shows that the proposed vibration absorber and damper reduce the vibration of the computer.

• Journal of Welding and Joining
• /
• v.27 no.5
• /
• pp.68-73
• /
• 2009

The bar horn is designed to increase uniformity of the displacement on the output face through simulation and experiments. Three-dimensional modal analysis is conducted using the finite element method to calculate the vibration mode and displacement on the output face, and the design of experiment (DOE) technique is employed to determine the optimum dimensions of the groove and slot so that the high amplitude uniformity of the bar horn is produced. Displacement of the bar horn was measured using the Laser Doppler Vibrometer (LDV), and the experimental results show good agreements with the predicted results. High uniformity of the bar horn is achieved with the dimensions of the groove and slot determined using the design equations.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.217-217
• /
• 2009

This paper describes the characteristics of polycrystalline 3C-SiC doubly clamped beam micro resonators. The polycrystalline 3C-SiC doubly clamped beam resonators with 60 ~ 100 ${\mu}m$ lengths, $10\;{\mu}m$ width, and $0.4\;{\mu}m$ thickness were fabricated using a surface micromachining technique. Polycrystalline 3C-SiC micro resonators were actuated by piezoelectric element and their fundamental resonant frequency was measured by a laser vibrometer in vacuum at room temperature. For the 60 ~ 100 ${\mu}m$ long cantilevers, the fundamental frequency appeared at 373.4 ~ 908.1 kHz. The resonant frequencies of doubly clamped beam with lengths were higher than simulated results because of tensile stress. Therefore, polycrystalline 3C-SiC doubly clamped beam micro resonators are suitable for RF MEMS devices and bio/chemical sensor applications.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.12
• /
• pp.2002-2008
• /
• 2001

Nonlinear vibration characteristics of a piezoelectric-type micro actuator used for hard disk drives are experimentally studied. The nonlinear characterisitics include hysteresis, superharmonic resonance, jump phenomenon, and shifting of natural frequencies. The vibration modes and frequencies of the commercial actuator of the Hutchinson's Magnum series are measured using a laser vibrometer. From harmonic excitation to the PZT acturator, we observe interesting hysteresis patterns with 3 times input frequency. It is shown that the micro actuator has the typical 3 times superhamonic resonances coupled to the first torsional and sway modes of the suspension.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.150-155
• /
• 2006

Speech intelligibility is investigated on a conference room-window glass coupled system. Using MLS(Maximum Length Sequency) signal as a sound source, acceleration and velocity responses of the window glass are measured by accelerometer and laser doppler vibrometer. MTF(Modulation Transfer Function) is used to identify the speech transmission characteristics of the room and window system. STI(Speech Transmission Index) is calculated by using MTF and speech intelligibility of the room and the window glass is estimated. Speech intelligibilities by the acceleration signal and the velocity signal are compared and the possibility of the wiretapping is investigated. Finally, intelligibility of the conversation sound is examined by the subjective test.

• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.323-326
• /
• 2004

에어컨 실외기의 구조 방사 소음을 줄이기 위해 제진재를 적용함에 있어 구조 인텐서티(structural intensity)법을 사용할 수 있다. 에어컨 실외기 각 패널의 법선 방향의 속도는 레이져 스케닝 바이브로미터(laser scanning vibrometer)에 의해 측정되며, 측정된 데이터는 공간 주파수 영역(k-domain)으로 변환하여 구조 인텐서티 계산에 필요한 공간 미분값이 구해진다. 이러한 과정을 통하여 계산된 구조 인텐서티 중 반동 전단 구조인텐서티(reactive shearing structural intensity)값이 가장 높은 부분에 사각형 형상의 제진재를 적용한다. 본 논문은 패널에 비해 그 크기가 작은 제진재의 적용으로 에어컨 실외기의 구조 방사 소음을 줄일 수 있음을 보여준다.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.455-460
• /
• 2007

A self-sensing circuit for piezo inkjet has been designed in order to monitor the operating condition during printing. In order to verify the circuit, both ink droplet images from strobe LED and vibration signals from the laser vibrometer were measured and compared with self-sensing signal. Experimental results show that self-sensing signal was effective in detecting the pressure wave change due to the bubble trapped in inkjet printhead.