• Journal of the Optical Society of Korea
• /
• 제16권3호
• /
• pp.313-317
• /
• 2012

We have evaluated a 1.3 ${\mu}m$ vertical-cavity surface-emitting laser (VCSEL), whose bottom mirror and central active layer were grown by metal organic chemical vapor deposition (MOCVD) and whose top mirror was covered with a dielectric coating, for 10 Gb/s data transmission over single-mode fibers (SMFs). Successful demonstration of error-free transmission of the directly modulated VCSEL signals at data rate of 10 Gb/s over a 10 km-long SMF was achieved for operating temperatures from $20^{\circ}C$ to $60^{\circ}C$ up to bit-error-rate (BER) of $10^{-12}$. The DC bias current and modulation currents are only 7 mA and 6 mA, respectively. The results indicate that the VCSEL is a good low-power consuming optical signal source for 10 GBASE Ethernet applications under controlled environments.

• 한국정보통신학회논문지
• /
• 제11권5호
• /
• pp.985-990
• /
• 2007

코히런트 광섬유 센서의 해상도를 향상시키기 위하여 광원의 코히런스 길이를 향상시키는 방법에 대하여 연구하였다. 넓은 파장범위에 걸쳐서 레이저 광을 생성할 수 있고 발광 파장대역이 장거리 전송이 가능한 통신용 광섬유의 저 손실 대역인 광섬유 레이저의 코히런스 길이를 향상시키기 위하여 레이저의 광궤환 기법을 이용하였다. 본 논문에서는 광섬유 레이저의 단거리 및 장거리 광궤환 루프가 코히런스 길이에 미치는 영향을 Mach-Zehnder Interferometer를 이용하여 연구하였다. 광궤환 전력량과 광궤환 루프에서의 변조형태가 코히런스에 미치는 영향을 조사하였다. 주파수 천이도는 200m 길이차를 갖는 비대칭 간섭계에서의 위상간섭 정도를 측정하여 계산하였다. 광섬유 레이저에서 단거리 광궤환 루프는 450kHz/sec로 주파수 천이도를 축소시키는데 효과가 있었고 장거리 광궤환 루프는 50kHz/sec로 주파수 천이도를 더 향상시키는 효과가 있음을 알 수 있었다. 실제 코히런트 광센서에 응용 시 고감도 침입자 감지가 기대된다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 학술대회지
• /
• pp.883-884
• /
• 2004

High-speed IC for time-division multiplexing (TDM) optical transmission systems have been designed and fabricated by using InP heterojunction-bipolar-transistor (HBT) technology. The driver IC was developed for driving external modulators, featuring differential outputs and the operation speed up to 10 Gbps with an output voltage swing of 1.3 Vpp at each output which was the limit of the measurement. Because -3 dB frequency was 20GHz, this circuit will be operated up to 20Gbps. 1.3Vpp differential output was achieved by switching 50 mA into a 50 $\Omega$ load. The power dissipation of the driver IC was 1W using a single supply voltage of -3.5Y. Input md output return loss of the IC were better than 10 dB and 15 dB, respectively, from DC to 20GHz. The chip size of fabricated IC was $1.7{\Box}1.2 mm^{2}$.

• 세라미스트
• /
• 제10권3호
• /
• pp.86-90
• /
• 2007

Novel photochromic oxide glasses are presented in this section. These glasses are based on phosphate formers containing both tungsten and antimony atoms. Exposure to visible continuous or pulsed laser beam results in an intense photochromic effect witch is shown to occur in the volume of the glass and results in a broad absorption band in the visible and near infrared. This effect was not identified to be related with a structural change and is assumed to be entirely electronic. A change in the absorption coefficient is observed in function of tungsten content, exposure time and increases with beam power. These glasses have been investigated regarding the possibility of holographic data storage using visible lasers sources. Changes in both refractive index and the absorption coefficient were measured using a holographic setup. The modulation of the optical constants is reversible by heat treatment.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.58.1-58.1
• /
• 2010

In solar cell module manufacturing, single solar cells has to be joined electrically to strings. Copper stripes coated with tin-silver-copper alloy are joined on screen printed silver of solar cells which is called busbar. The bus bar collects the electrons generated in solar cell and it is connected to the next cell in the conventional module manufacturing by a metal stringer using conventional hot air or infrared lamp soldering systems. For thin solar cells, both soldering methods have disadvantages, which heats up the whole cell to high temperatures. Because of the different thermal expansion coefficient, mechanical stresses are induced in the solar cell. Recently, the trend of solar cell is toward thinner thickness below 180um and thus the risk of breakage of solar cells is increasing. This has led to the demand for new joining processes with high productivity and reduced error rates. In our project, we have developed a new method to solder solar cells with a laser heating source. The soldering process using diode laser with wavelength of 980nm was examined. The diode laser used has a maximum power of 60W and a scanner system is used to solder dimension of 6" solar cell and the beam travel speed is optimized. For clamping copper stripe to solar cell, zirconia(ZrO)coated iron pin-spring system is used to clamp both joining parts during a scanner system is traveled. The hot plate temperature that solar cell is positioned during lasersoldering process is optimized. Also, conventional solder joints after $180^{\circ}C$ peel tests are compared to the laser soldering methods. Microstructures in welded zone shows that the diffusion zone between solar cell and metal stripes is better formed than inIR soldering method. It is analyzed that the laser solder joints show no damages to the silicon wafer and no cracks beneath the contact. Peel strength between 4N and 5N are measured, with much shorter joining time than IR solder joints and it is shown that the use of laser soldering reduced the degree of bending of solar cell much less than IR soldering.

• 한국소프트웨어감정평가학회 논문지
• /
• 제15권1호
• /
• pp.71-78
• /
• 2019

광대역 광통신 시스템에 사용되는 레이저는 우수한 주파수 선택성과 모드 안정성을 가져야한다. DFB(Distributed Feedback) 레이저는 고주파로 전류 변조를 하더라도 발진 주파수의 변화가 적다. 본 연구에서는 무반사 코팅을 하지 않은, 두 거울 면을 가진 1.55um의 파장을 갖는 DFB 레이저에서 이득 격자와 굴절률 격자가 동시에 존재할 때, 시뮬레이션 소프트웨어를 개발하여 종 방향으로의 발진 모드의 빔 분포를 해석하였다. 굴절률 격자와 이득 격자가 거울 면에서 갖는 위상 값의 변화에 따라서 DFB 레이저의 발진 모드에 대한 빔 분포 |R(z)|와 |S(z)|, 그리고 방사전력비 P_l/P_r를 비교 검증하였다. 거울 면에서의 격자 위상에 관계없이 발진 모드의 문턱 전류를 낮추고 주파수 안정성을 높이기 위해서는, κL이 8보다 커야한다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권3호
• /
• pp.274-286
• /
• 2016

This paper presents a 4-channel multi-rate vertical-cavity surface-emitting laser (VCSEL) driver. In order to keep the output power constant with respect to the process, voltage, temperature (PVT) variations, this research proposes automatic power and magnitude. For the fast settling time, the high-speed 10-bit time-interleaved Flash-successive approximation analog to digital converter (Flash-SAR ADC) is proposed and shared for automatic power and magnitude calibration to reduce the die area and power consumption. This chip is fabricated using $0.13-{\mu}m$ CMOS technology and the die area is $4.2mm^2$. The power consumption is 117.84 mW per channel from a 3.3 V supply voltage at 10 Gbps. The measured resolution of bias /modulation current for APC/AMC is 0.015 mA.

• 한국광학회지
• /
• 제30권4호
• /
• pp.167-173
• /
• 2019

본 논문에서는 고출력 광섬유 레이저의 유도 브릴루앙 산란 억제 특성을 분석하기 위하여, 구형파, 사인파, 임의파 조건의 온도구배 기구부를 설계 및 제작하였다. 또한 전광섬유 MOPA (master oscillator power amplifier) 구조의 이터븀 첨가 편광유지 광섬유 증폭기를 제작하였으며, 온도구배 조건별 역반사 스펙트럼 및 출력을 측정하였다. 구형파 조건의 온도구배에 의해 유도 브릴루앙 산란이 가장 효과적으로 억제되었으며, PRBS (pseudo-random binary sequence) 위상변조 조건과 온도구배 간의 유도 브릴루앙 산란 특성에 끼치는 상호 영향성을 분석하였다.

• 한국통신학회논문지
• /
• 제19권10호
• /
• pp.1957-1964
• /
• 1994

본 논문에서 CW(Continuos Wave) 레이저를 광원으로 사용하고 음향 광 소자(Acousto-Optic Device:AOD)의 공간 적분이론 및 CCD(Change Coupled Device)의 시간 적분이론을 이용하여 실 시간 처리가 가능한 합성 개구면 레이다(Synthetic Aperture Radar;SAR)처리기 시스템을 구현하였다. 제안된 시스템의 장점은 구동회로가 요구되지 않는다. 제안된 SAR 처리기 시스템은 선형 주파수 변조 신호(chirp)를 레이다 신호로 사용하였으며, 단위 표적에 대한 수신 데이타는 1차원 데이타로서 Z 80 보드와 전자회로를 이용하여 제작하였다. 또한 CW레이저를 사용함에 따라 발생되는 chirp 촛점화의 유동(smear)현상을 방지하기 위하여 AOD의 Brag 회절 각도를 이용하여 광원을 펄스화 하였으며, 제작한 chirp 신호는 펄스와 동기를 맞추어 구성하였다. 구성된 SAR 처리기 시스템의 CCD에 검출되는 영상과 데이타를 실험 및 분석한 결과는 단위표적의 거리가 증가함에 따라 탐지효과 감소되었고, chirp 신호 대역폭의 증가에 따라 분해능력이 향상되었으며, 펄스폭의 감소에 따라 유동(smear)현상이 감소하였다. 따라서 본 논문에서 실험결과는 제안된 시스템을 실시간 처리 시스템으로써 사용할 수 있음을 확인하였다.

• 전자공학회논문지A
• /
• 제32A권3호
• /
• pp.1-9
• /
• 1995

In the B-ISDN using satellite between geo-satellites and earth stations, the laser having high security and broad band width has to be used as a carrier for transmitting massive information of visual, vocal, and high rate data. In this paper, by computer simulation we analyzed the number of optical detector array of optical satellite communication downlink in case of using channel coding and no channel coding for BISDN between geo-satelites and earth stations under clear weather condition. It was supposed that 1 watt semiconductor laser was used and as modulation method, the binary FSK was used. The data rate of 10Gbps was used for B-ISDN. Also, hardly affected by atmospheric absorption 1.55$\mu$m wave-length was used to reduce influence of dispersion and chirp generated at a high speed transmission. We analyzed the received power, SNR and BER. The number of optical detector array was determined to satisfy for the BER less than 10$^{-7}$. Also, we ananlyzed the possibility of reducting the number of optical detector array in case of using channel coding. the number of optical detector array is one in the region where the elevation nangle is between 38$^{\circ}$ and 90$^{\circ}$ and two where the elevation angle is between 33$^{\circ}$ and 37$^{\circ}$ and three where the elevation angle is between 30$^{\circ}$ and 32$^{\circ}$ and increases per one as the elevation angle decreases per 1.deg.. So in the region where the elevation angle is 25$^{\circ}$, the number of optical detector arrays is eight. In case of using channel coding, the number of optical detector arrays decreases to five in the region where the elevation angle is 25$^{\circ}$. Therefore, we remaark the advantage of the channelcoding to decrease the size of received antenna and the number ob optical detector arrays.