• The Korean Journal of Ceramics
• /
• 제3권3호
• /
• pp.159-162
• /
• 1997

Diamond was uniformly nucleated on large area Si(001) substrate (3cm$\times$4cm) using the low pressure magnetoactive microwave plasma chemical vapor deposition. $CH_4/He$ gas mixture was used as source gas in order to obtain high radical density in the nucleation enhancement step. $CH_3$radical density was measured by means of infrared laser absorption spectroscopy. The effect of substrate bias voltage on diamond nucleation was examined. The results showed that a suitable positive bias voltage appled to the substrate with respect to the chamber could enhance diamond nucleation while a negative bias voltages leaded to deposition of only non-diamond phase carbon.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2000년도 제18회 학술발표회 논문개요집
• /
• pp.212-212
• /
• 2000

Since the first obserbvation of carbon nanotubes, extensive researches have been done for the synthesis using arc discharge, laser vaporization, and plasma-enhanced chemical vapor deposition. Carbon nanotubes have unique physical and chemical properties and can allow nanoscale devices. Vertically aligned carbon nanotubes with high quality on a large area is particularly important to enable both fundamental studies and applications, such as flat panel displays and vacuum microelectronics. we have grown vertically aligned carbon nanotubes on a large area of Si substrates by thermal chemical vapor deposition using C2H2 gas at 750-950$^{\circ}C$. we deposited catalytic metal on Si susbstrate using thermal evaporation. The nanotubes reveal highly purified surface. The carbon nanotubes have multi-wall structure with a hollow inside and it reveals bamboo structure agreed with base growth model. Figure 1 shows SEM micrograph showing vertically aligned carbon nanotubes whih were grown at 950$^{\circ}C$ on a large area (20mm${\times}$30mm) of Si substrates. Figure 2 shows TEM analysis was performed on the carbon nanotubes grown at 950$^{\circ}C$ for 10 min. The carbon nanotubes are multi-wall structure with bamboo shape and the lack of fringes inside the nanotube indicates that the core of the structure is hollow. In our experiment, carbon nanotubes grown by the thermal CVD indicate base growth model.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.252.2-252.2
• /
• 2013

ZnO nanostructures have a lot of interest for decades due to its varied applications such as light-emitting devices, power generators, solar cells, and sensing devices etc. To get the high performance of these devices, the factors of nanostructure geometry, spacing, and alignment are important. So, Patterning of vertically- aligned ZnO nanowires are currently attractive. However, many of ZnO nanowire or nanorod fabrication methods are needs high temperature, such vapor phase transport process, metal-organic chemical vapor deposition (MOCVD), metal-organic vapor phase epitaxy, thermal evaporation, pulse laser deposition and thermal chemical vapor deposition. While hydrothermal process has great advantages-low temperature (less than $100^{\circ}C$), simple steps, short time consuming, without catalyst, and relatively ease to control than as mentioned various methods. In this work, we investigate the dependence of ZnO nanowire alignment and morphology on si substrate using of nanosphere template with various precursor concentration and components via hydrothermal process. The brief experimental scheme is as follow. First synthesized ZnO seed solution was spun coated on to cleaned Si substrate, and then annealed $350^{\circ}C$ for 1h in the furnace. Second, 200nm sized close-packed nanospheres were formed on the seed layer-coated substrate by using of gas-liquid-solid interfacial self-assembly method and drying in vaccum desicator for about a day to enhance the adhesion between seed layer and nanospheres. After that, zinc oxide nanowires were synthesized using a low temperature hydrothermal method based on alkali solution. The specimens were immersed upside down in the autoclave bath to prevent some precipitates which formed and covered on the surface. The hydrothermal conditions such as growth temperature, growth time, solution concentration, and additives are variously performed to optimize the morphologies of nanowire. To characterize the crystal structure of seed layer and nanowires, morphology, and optical properties, X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), Raman spectroscopy, and photoluminescence (PL) studies were investigated.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.207-207
• /
• 2010

Both ZnO and GaN have excellent physical properties in optoelectronic devices such as blue light emitting diode (LED), blue laser diode (LD), and ultra-violet (UV) detector. The ZnO/GaN heterostructure, which has a potential to achieve the cost efficient LED technology, has been fabricated by using radio frequency (RF) sputtering, pyrolysis, metal organic chemical vapor deposition (MOCVD), direct current (DC) arc plasmatron, and pulsed laser deposition (PLD) methods. Among them, the PLD system has a benefit to control the composition ratio of the grown film from the mixture target. A 500-nm-thick ZnO film was grown by PLD technique on c-plane GaN/sapphire substrates. The post annealing process was executed at some varied temperature between from $300^{\circ}C$ to $900^{\circ}C$. The morphology and crystal structural properties obtained by using atomic force microscope (AFM) and x-ray diffraction (XRD) showed that the crystal quality of ZnO thin films can be improved as increasing the annealing temperature. We will discuss the post-treatment effect on film quality (uniformity and reliability) of ZnO/GaN heterostructures.

• 열처리공학회지
• /
• 제13권5호
• /
• pp.318-323
• /
• 2000

The planarization of rough polycrystalline diamond films synthesized by DC arc discharge plasma jet CVD (chemical vapor deposition) was attempted using KrF excimer laser pulses. The effects of laser incidence angle and reaction gases (ozone and oxygen) on etching rate of diamond were studied. The temperature change of diamond and graphite with different laser fluences was calculated by computer simulation to explain the etching behavior of diamond films. The threshold energy density from the experiment for etching of pure crystalline diamond was about $1.7J/cm^2$ and fairly matched the simulation value. Preferential etching of a particular crystallographic plane was observed through scanning electron microscopy. The etching rate of diamond with ozone was lower than that with oxygen. When the angle of incidence was $80^{\circ}$ to the diamond surface normal, the peak-to-valley surface roughness was Significantly reduced from $20{\mu}m$ to $0.5{\mu}m$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.I
• /
• pp.496-498
• /
• 2005

We reported that high dielectric hafnium oxide nano-film deposited by thermal atomic layer deposition on the poly-silicon film (poly-Si). The poly -Si film was produced by plasma enhanced chemical vapor deposition and excimer laser annealing. We used the hafniu m chloride ($HfCl_4$) and water as the precursors and analyzed the hafnium oxide film by transmission electron microscope and secondary ion mass spectrometer. Hafnium oxide produced by the ALD method showed very good coverage on the rough surface of poly-Si film. While deposited with 200 cycles, these hafnium oxide films revealed a relatively smooth surface and good uniformity, but the cumulative roughness produced by the incomplete reaction was apparent when the amount of deposition cycle increased to 600 cycles.

• 전자공학회논문지A
• /
• 제32A권1호
• /
• pp.159-165
• /
• 1995

A double-heterostructure mesa-stripe-geometry laser diode integrated with thermoelectric Peltier cooler has been designed and fabricated. Epi-layers have been grown by metal organic chemical vapor deposition(MOCVD) method. Peltier cooling effect has been measured for devices with a mesa width of 14$\mu$m and a cavity length of 380$\mu$m. The effects of thermoelectric cooling could be shown by measuring the optical output of the laser with the increase of the current in the thermoelectric cooler. While the input courrent of the laser was maintained at 250mA, the optical output was decreased from 4.8mW to 3.8mW due to heating, but with the thermoelectric cooler on the optical output power was recovered by more than 40%. The results show that the complicated cooling device is not needed since the cooling can be achevied by the developement of the fabrication processing.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2002년도 International Meeting on Information Display
• /
• pp.689-691
• /
• 2002

Well-aligned multi-wall carbon nanotubes (MWCNTs) have been grown on both Coming glass and silicon substrates at about 400 $^{\circ}C$ by a modified plasma - enhanced chemical vapor deposition system. We have investigated laser irradiation effect on carbon nanotube surface by using an ultra - violet laser. The laser operated to modify structural defect of was carbon nanotube and to ablate possible contamination of carbon nanotube surface. The morphology and surface transformation of MWCNTs as analyzed by a SEM. In addition, the field emission measurement was also carried out in a vacuum chamber with a $10^{-7}$ Torr base pressure by applying bias voltages up to 1000V.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2000년도 Proceedings of 5th International Joint Symposium on Microeletronics and Packaging
• /
• pp.109-109
• /
• 2000

Recently, carbon nanotube has been investigating for field emission display ( (FED) applications due to its high electron emission at relatively low electric field. However, the growing of carbon nanotube generally requires relatively high temperature processing such as arc-discharge (5,000 ~ $20,000^{\circ}C$) and laser evaporation (4,000 ~ $5,000^{\circ}C$) methods. In this presentation, low temperature growing of carbon nanotube by plasma enhanced chemical vapor deposition (PECVD) using nickel catalyst which is compatible to conventional FED processing temperature will be described. Carbon n notubes with average length of 100 run and diameter of 2 ~ $3\mu$ill were successfully grown on silicon substrate with native oxide layer at $550^{\circ}C$using nickel catalyst. The morphology and microstructure of carbon nanotube was highly depended on the processing temperature and nickel layer thickness. No significant carbon nanotube growing was observed with samples deposited on silicon substrates without native oxide layer. This is believed due to the formation of nickel-silicide and this deteriorated the catalytic role of nickel. The formation of nickel-silicide was confirmed by x-ray analysis. The role of native oxide layer and processing parameter dependence on microstructure of low temperature grown carbon nanotube, characterized by SEM, TEM XRD and R없nan spectroscopy, will be presented.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.1320-1322
• /
• 2005

Microcrystalline silicon films were deposited on glass substrate by using plasma-enhanced chemical vapor deposition (PECVD) method. The crystalline volume fraction was estimated by means of Raman spectrometer with argon laser as light source. The high hydrogen dilution of silane gas was used for increase in content of crystal silicon phase.