• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.91-93
• /
• 2005

Forming sheet metal by laser-induced thermal stresses (laser forming) has been extensively studied, and the research has focused on two-dimensional geometries using a multi-pass straight line scan. Recently there came out some useful studies or three-dimensional laser forming which is applied to doubly curved shapes. The task of 3D laser forming sheet metal is to determine a set of process parameters such as laser scanning paths, laser power and scanning speed that will make a given shape. New method for laser forming of a doubly curved surface by using geometrical information was proposed and verified by experiments. This method shows good performance in the sense of calculation time and accuracy compared to the inherent strain method.

• 한국인터넷방송통신학회논문지
• /
• 제15권1호
• /
• pp.187-190
• /
• 2015

최근, 현대인들의 필수품인 '스마트 폰'이 상용화 되면서 곳곳에 '스마트' 한 생활을 위한 기술들이 개발되고 있다. 이에 본 논문은 레이저를 이용한 디스플레이 및 스피커와 방향제를 엘리베이터 내부에 도입하여 내부 화면의 다양화를 연출하고, 핸드오버기술로 지속적인 와이파이 호환이 가능한 이용자 단말기 상의 엘리베이터 조절 화면 출력기능 탑재로 이용자의 스마트폰을 통해 엘리베이터를 조작할 수 있으며 승강기 외부 상단에 장착된 키넥트로 이용자의 동작을 인식하여 작동되는 기존 엘리베이터 시스템과 차별화된 새로운 스마트스크린 엘리베이터 시스템을 제안하고자 한다. 마지막으로 엘리베이터 제조사, 유통사, 소비자 각 집단 200명을 대상으로 레이저스크린 엘리베이터의 상용화에 대한 설문조사를 진행한다.

• 대한소아치과학회지
• /
• 제24권1호
• /
• pp.139-147
• /
• 1997

Argon laser used in this case report, is special in having two wavelength of 488, 514nm blue-green visible light spectrum. Blue light is used for composite resin polymerization and caries detection. Green light is used for soft tissue surgery and coagulation. Maximum absorption of this laser light occurs in red pigmentation such as hemoglobin. The argon laser may be well-suited for selective destruction of blood clots and hemangioma with minimal damage to adjacent tissues. Argon laser light penetrates tissue to the 1 mm depth, so its thermal intensity is lower than $CO_2$ laser light. Also, due to its short wavelength it can be focused in a small spot and even single gene can be excised by this laser and microscopy. After applicating argon laser to 4 patient for surgical procedure and to 1 patient for curing the composite resin, following results were obtained. 1. Improved visibility were gained due to hemostasis and no specific technique were needed according to easy recontouring of the tissue. 2. Ability to use by contact mode, tactile sense was superior but tissue dragability and accumulation of tissue on the tip needed sweeping motion. 3. Additive local anesthetic procedure was needed. 4. No suture and less curing time reduced chair time, this made argon laser available in pediatric dentistry.

• 복식문화연구
• /
• 제28권6호
• /
• pp.738-754
• /
• 2020

As a cultural feature of, the relics of the Royal Tomb of King Muryeong are suitable design content for applying with sophisticated production and delicate molding laser cutting techniques. The purpose of this study is to develop modern bag designs using relics of the Royal Tomb of King Muryeong of Baekje using laser-cutting techniques. First, the historical background and meaning of Baekje's cultural content were explored. Second, the principle of laser-cutting techniques were explored, laser-cutting techniques applied to modern fashion and bag design were examined, and bag design characteristics were analyzed. Third, based on prior research, the criteria for the development of bag design, from which eight bag design were developed that combine modern popularity and functionality utilizing Baekje cultural content and using laser-cutting techniques to apply the textile design developed by researchers in 2013 (modified to match laser-cutting techniques). The research results show that bag were clutch, tote, shoulder, and mini. Gold, silver, brown, beige, and navy colors were arranged, based on black/white contrast. Cow, lambskin, washed snakeskin, mesh, and Saffiano leather were used. For the pattern-applying technique, this study showed that a new digital technique, which is laser-cutting techniques could be combined with contemporary bag designs. Moreover, a bag design was developed that has a modern sense and functionality as well as Korean formativeness, which is significant.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.1994-1998
• /
• 2005

Characteristic analysis of the depth measurement system with a laser, a camera and a rotating mirror has been done and the parameter calibration technique for it has been proposed. In the proposed depth measurement system, the laser beam is reflected to the object by the rotating mirror and again the position of the laser beam is observed through the same mirror by the camera. The depth of the object pointed by the laser beam is computed depending on the pixel position on the CCD. There involved several number of internal and external parameters such as inter-pixel distance, focal length, position and orientation of the system components in the depth measurement error. In this paper, it is shown through the error sensitivity analysis of the parameters that the most important parameters in the sense of error sources are the angle of the laser beam and the inter pixel distance. The calibration techniques to minimize the effect of such major parameters are proposed.

• 대한정형도수물리치료학회지
• /
• 제27권3호
• /
• pp.1-15
• /
• 2021

Objective: The purpose of this study was to examine the differences in joint position sense (JPS), force sense (FS), and performance level of the upper extremities according to the injury and pain experiences of Korean elite archers. Methods: A total of 15 subjects were briefed about the purpose of this study and agreed to participate voluntarily. JPS was evaluated using the laser-point attached to the wrist while aiming at the target. The difference when relocating while aiming was used as JPS factor. FS was evaluated using load cell through reproduces same muscle strength. Fear-Avoidance Beliefs Questionnaire (FABQ) was used to evaluate psychosocial factors, Kerlan-Jobe Orthopedic Clinic overhead athlete scores (KJOC) and numerical rating scale (NRS) was used to evaluate pain. and performance was evaluated by tournament match score. Results: There is a strong correlation between the current pain and KJOC. Moreover, moderate correlation between KJOC and FABQ also current pain and both upper trapezius and lower trapezius in elite archers. The mean (SD) between groups based on current pain display relatively large margin in force sense than without pain group. The result presents that there is a significant difference in performance and pain. There is a significant difference in the force sense of the upper and lower trapezius and pain. Conclusions: Result present there is a significant difference in functional level in the average comparison between groups according to the presence of absence of current pain. There is a significant difference in the force sense of the upper trapezius as well as lower trapezius and without pain group present a relatively low joint position sense error compared to the groups.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 영호남 합동 학술대회 및 춘계학술대회 논문집 센서 박막 기술교육
• /
• pp.125-129
• /
• 2006

The analysis of the depth measurement system with multi-sensors (laser, camera, mirror) has been done and the parameter calibration technique has been proposed. In the proposed depth measurement system, the laser beam is reflected to the object by the rotating mirror and again the position of the laser beam is observed through the same mirror by the camera. The depth of the object pointed by the laser beam is computed depending on the pixel position on the CCD. There involved several number of internal and external parameters such as inter-pixel distance, focal length, position and orientation of the system components in the depth measurement error. In this paper, it is shown through the error sensitivity analysis of the parameters that the most important parameters in the sense of error sources are the angle of the laser beam and the inter pixel distance.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.263-266
• /
• 2002

An optical method for surface roughness estimation based on statistical analysis of the light intensity of a scattered laser beam pattern. The method is very simple but has a disadvantage that no more information than the averaged roughness is estimated. In this study a new try was conducted to derive more advanced surface information from the details of the light intensity distribution. Some periodic ripples among the light intensity distribution being assumed to relate with scratch left on the machined surface, a corresponding surface profile is estimated from the ripples using FFT and IFFT algorithm. IFFT technique is used to extract some dominant signal components among the intensity distribution. Compared to the measured profiles by a stylus type surf-tester, the profiles obtained through the proposed method are probably acceptable in a sense of the profile shape. Calibration of the amplitude needs more works in the future.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 춘계학술대회 논문집
• /
• pp.5-5
• /
• 2010

The depth of the object pointed by the laser beam is computed depending on the pixel position on the CCD There involved several number of internal and external parameters such as inter-pixel distance, focal length, position and orientation of the system components in the depth measurement error. In this paper, it is shown through the error sensitivity analysis of the parameters that the most important parameters in the sense of error sources are the angle of the laser beam and the inter pixel distance. Also, the calibration technique to minimize their effect for the depth computation is proposed.

• 한국산학기술학회논문지
• /
• 제3권4호
• /
• pp.227-232
• /
• 2002

시각장애인의 보행을 유도하기 위한 전자보행기로, 소닉가이드, 모와트센서, 바이오닉 지팡이 등이 개발되었으나, 가격이 비싸거나, 훈련이 어렵다는 이유 등으로 국내에서는 거의 보급되어 있지 않고 있다. 따라서, 본 연구에서는 청각에 의한 장해물을 인식 개념을 고려하여 주변의 장해물의 파악에 특별한 훈련이 필요치 않으며, 저렴한 가격의 전자보행기의 개발 을 위한 기본 연구로 시각장애인의 장해물인지특성의 검토 및 장해물 인지특성을 고려한 초음파형 전자보행유도기의 프로토콜을 통한 보행시험을 실시하였다.