• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.4
• /
• pp.568-573
• /
• 1996

The amorphous silicon films deposited by low pressure chemical vapor deposition are crystallized by the various annealing techniques including low-temperature furnace annealing and two-step annealing. Two-step annealing is the combination of furnace annealing at 600 [.deg. C] for 24 h and the sequential furnace annealing at 950 [.deg. C] 1h or the excimer laser annealing. It s found that two-step annealings reduce the in-grain defects significantly without changing the grain boundary structure. The performance of the poly-Si thin film transistors (TFTs) produced by employing the tow-step annealing has been improved significantly compared with those of one-step annealing. (author). 13 refs., 6 figs., 1 tab.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.430-430
• /
• 2008

Using multi plasma enhanced chemical vapor deposition system (Multi-PECVD), p-a-Si:H deposition layer as a $p^+$ region which was annealed by laser (Q-switched fiber laser, $\lambda$ = 1064 nm) on an n-type single crystalline Si (100) plane circle wafer was prepared as new doping method for single crystalline interdigitated back contact (IBC) solar cells. As lots of earlier studies implemented, most cases dealt with the excimer (excited dimer) laserannealing or crystallization of boron with the ultraviolet wavelength range and $10^{-9}$ sec pulse duration. In this study, the Q-switched fiber laser which has higher power, longer wavelength of infrared range ($\lambda$ = 1064 nm) and longer pulse duration of $10^{-8}$ sec than excimer laser was introduced for uniformly deposited p-a-Si:H layer to be annealed and to make sheet resistance expectable as an important process for IBC solar cell $p^+$ layer on a polished n-type Si circle wafer. A $525{\mu}m$ thick n-type Si semiconductor circle wafer of (100) plane which was dipped in a buffered hydrofluoric acid solution for 30 seconds was mounted on the Multi-PECVD system for p-a-Si:H deposition layer with the ratio of $SiH_4:H_2:B_2H_6$ = 30:120:30, at $200^{\circ}C$, 50 W power, 0.2 Torr pressure for 20 minutes. 15 mm $\times$ 15 mm size laser cut samples were annealed by fiber laser with different sets of power levels and frequencies. By comparing the results of lifetime measurement and sheet resistance relation, the laser condition set of 50 mm/s of mark speed, 160 kHz of period, 21 % of power level with continuous wave mode of scanner lens showed the features of small difference of lifetime and lowering sheet resistance than before the fiber laser treatment with not much surface damages. Diode level device was made to confirm these experimental results by measuring C-V, I-V characteristics. Uniform and expectable boron doped layer can play an important role to predict the efficiency during the fabricating process of IBC solar cells.

• Nuclear Engineering and Technology
• /
• v.50 no.2
• /
• pp.229-236
• /
• 2018

Accident-tolerant fuels (ATFs) are currently of high interest to researchers in the nuclear industry and in governmental and international organizations. One widely studied accident-tolerant fuel concept is multilayer cladding (also known as coated cladding). This concept is based on a traditional Zr-based alloy (Zircaloy-4, M5, E110, ZIRLO etc.) serving as a substrate. Different protective materials are applied to the substrate surface by various techniques, thus enhancing the accident tolerance of the fuel. This study focuses on the results of testing of Zircaloy-4 coated with pure chromium metal using the cold spray (CS) technique. In comparison with other deposition methods, e.g., Physical vapor deposition (PVD), laser coating, or Chemical vapor deposition techniques (CVD), the CS technique is more cost efficient due to lower energy consumption and high deposition rates, making it more suitable for industry-scale production. The Cr-coated samples were tested at different conditions ($500^{\circ}C$ steam, $1200^{\circ}C$ steam, and Pressurized water reactor (PWR) pressurization test) and were precharacterized and postcharacterized by various techniques, such as scanning electron microscopy, Energy-dispersive X-ray spectroscopy (EDX), or nanoindentation; results are discussed. Results of the steady-state fuel performance simulations using the Bison code predicted the concept's feasibility. It is concluded that CS Cr coating has high potential benefits but requires further optimization and out-of-pile and in-pile testing.

• Korean Journal of Materials Research
• /
• v.9 no.1
• /
• pp.86-91
• /
• 1999

We have fabricated high-$\textrm{T}_c$ superconducting $\textrm{YBa}_{2}\textrm{Cu}_{3}\textrm{O}_{7-x}$(YBCO) grain boundary junctions at a step-edge on (001) $\textrm{SrTiO}_3$(STO) substrates. A diamond-like carbon (DLC) film grown by plasma enhanced chemical vapor deposition were used as an ion milling mask to make steps on the STO (100) single crystal and was removed by an oxygen reactive ion etch process. The c-axis oriented YBCO and TO thin films were deposited epitaxially on the STO substrate with a step-edge by pulsed laser deposition. The grain boundary junctions were formed at the top and the bottom of the step. The junctions worked at temperatures above 77 K, and had I\ulcornerR\ulcorner products of 7.5mV at 16K and 0.3 mV at 77K, respectively. The I-V characteristics of these junctions showed the shape of the two noisy resistively shunted junction model.

• Carbon letters
• /
• v.14 no.3
• /
• pp.175-179
• /
• 2013

Isolated single wall carbon nanotubes (SWCNTs) were synthesized by chemical vapor deposition (CVD) using a liquid precursor (xylene) as a carbon source. Transmission electron microscopy (TEM) and atomic force microscopy confirmed the isolated structure of the SWCNTs. Micro-Raman measurements showed a tangential G-band peak ($1590cm^{-1}$) and radial breathing mode (RBM) peaks ($150-240cm^{-1}$). The tube diameters determined from the RBM frequencies are in good agreement with those obtained from TEM. The chirality of the isolated SWCNTs could be determined based on the energy of the laser and their diameter. A further preliminary study on the nitrogen doping of isolated SWCNTs was carried out by the simple use of acetonitrile dissolved in the precusor.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.582-582
• /
• 2013

Oxide TFT (thin film transistor) active channel layer에 대한 저온 열처리 공정은 투명하고 flexibility을 기반으로하는 display 산업과 AMOLED (active matrix organic light emitting diode) 분야 등 다양한 분야에서 필요로 하는 기술로서 많은 연구가 이루어지고 있다. 과거 active layer는 ALD (atomic layer deposition), CVD (chemical vapor deposition), pulse laser deposition, radio frequency-dc (RF-dc) magnetron sputtering 등과 같은 고가의 진공 장비를 이용하여 증착 되어져 왔으나 현재에는 진공 장비 없이 spin-coating 후 열처리 하는 저가의 공정이 주로 연구되어 지고 있다. Flexible 기판들은 일반적인 OTFT (oxide thin films Transistor)에 적용되는 열처리 온도로 공정 진행시 열에 의한 기판의 손상이 발생한다. Flexible substrate의 열에 의한 기판 손상을 막기 위해 저온 열처리 공정이 연구되고 있지만 기존 열처리와 비교하여 소자의 특성 저하가 동반 되었다. 본 연구에서는 Si 기판위에 SiO2 (100)를 절연층으로 증착하고 그 위에 IZO (indium zinc oxide) solution을 spin-coating 한뒤 $250^{\circ}C$ 이하의 온도에서 열처리하였다. 저온 공정으로 인하여 소자의 특성 저하가 동반 되었으므로 소자의 저하된 특성 복원하고자 post-treatment로 고가의 진공장비가 필요 없고 roll-to roll system 적용이 수월한 remote-type의 APP (atmospheric pressure plasma) 처리를 하였다. Post-treatment로 APP를 이용하여 $250^{\circ}C$ 이하에서 소자에 적용 가능한 on/off ratio를 얻을 수 있었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.175-175
• /
• 2008

투명전극으로 사용되고 있는 Indium tin oxide (ITO) 박막은 전기적 전도도와 기판과의 접확성, 화학적 안정성, 광투과율 등의 특성과 함께 우수한 전기 광학적 거동을 보이고 있다. 그러나 ITO는 고가의 재료이기 때문에 대체 투명전극으로 Al을 도핑한 ZnO 박막의 연구가 활발히 진행되고 있다. ZnO:Al 박막은 chemical vapor deposition, reactive magnetron sputtering, electron-beam evaporation, pulsed laser deposition 등의 당양한 방법을 이용하여 증착하였다. 그러나 최근 낮은 온도에서 대면적의 균일성과 우수한 특성 때문에 atomic layer depositon (ALD) 방법을 이용하여 많은 연구가 진행되고 있으며, 이런 투명전극은 태양전지를 위해 연구되어지고 있다. 따라서 본 연구에서는 ALD 방법으로 Al의 도핑 양을 조절하여, ZnO:Al 박막을 제조하여 그 특성을 평가하고, 또한 ZnO TFT를 제작하여 발표하고자 한다. ZnO와 ZnO:Al 박막은 실리콘과 유리 기판 위에 ALD (Lucida-D200, NCD Technology) 장치로 증착하였다. DEZn, TMA, $H_2O$는 ZnO와 ZnO:Al 박막을 증착하기 위한 전구체와 반응가스로 사용하였다. 증착된 박막은 XRD와 HRTEM을 이용하여 결정구조와 미세구조를 분석하였다. AFM과 4-point probe를 이용하여 증착된 박막의 표면 거칠기와 면저항을 관찰하였다. semiconductor parameter 분석기를 이용하여 제작된 ZnO TFT를 평가하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.42-42
• /
• 2007

In the future, electronic components will be integrated on flexible polymer substrates and then miniaturized by thin films using suitable thin film technologies. In this article, the concept of a room temperature CVD is demonstrated using $Bi_3NbO_7$ (BNO) films with a cubic fluorite structure and their structural and electrical properties were investigated in films deposited without substrate heating. Effects of substrate temperature on electrical properties of BNO films were also studied. Films deposited without substrate heating (real temperature of $50^{\circ}C$) show partially crystallized BNO single phases with grain size of approximately 6.5 nm. Their dielectric and leakage properties are comparable to those of films deposited by pulsed laser deposition at room temperature. The concept of room temperature CVD will become a new paradigm in the deposition of dielectric thin films for flexible electron device applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.259-259
• /
• 2011

염료감응형 태양전지(Dye-Sensitized Solar Cells:DSSC)는 환경 친화적이며, 저가의 공정에 대한 가능성으로 기존의 고가의 결정질 실리콘 태양전지의 경제적인 대안으로 각광을 받고 있다. 최근 염료감응형 태양전지는 투명 전도성 산화막(Transparent Conducting Oxide : TCO)으로 사용되는 Fluorine Tin Oxide (FTO)가 증착된 유리기판 위에 주로 제작된다. FTO는 낮은 비저항과 가시광선 영역에서 높은 투과도를 가지는 우수한 전기-광학적 특성을 갖지만, 비교적 공정이 까다로운 Chemical Vapor Deposition (CVD)법으로 제조하며, 전체 공정비용의 60%를 차지하는 높은 생산단가로 인해 현재 FTO를 대체할 재료개발 연구가 활발히 진행되고 있다. 그 중 ZnO (Zinc Oxide)는 우수한 전기-광학적 특성과 비교적 저렴한 가격으로 새로운 TCO로써 주목받고 있다. ZnO는 넓은 energy band gap (3.4 [eV])의 육방정계 울자이트(hexagonal wurtzite) 결정 구조를 가지는II-VI족 n형 반도체 물질이며, III족 금속원소인 Al, Ga 및 In 등의 불순물을 첨가하면 TCO로서 우수한 전기-광학적 특성과 안정성을 나타낸다. 이들 물질중 $Zn^{2+}$ (0.060 nm)의 이온반경과 유사한 $Ga^{2+}$0.062 nm) 이온이 ZnO의 격자반경을 최소화 시킬 수 있다는 장점으로 최근 주목 받고 있다. 하지만 Ga-doped ZnO (GZO)의 경우 DSC에 사용되는 루테늄 계열의 산성 염료 하에 장시간 두면 표면이 파괴되는 문제가 발생하며, $TiO_2$ paste를 Printing 후 열처리하는 과정에서도 박막의 파괴가 발생할 수 있다. 이를 방지하기 위해 $TiO_2$ Blocking Layer를 GZO 투명전극 위에 증착하였다. 또한, $TiO_2$ Blocking Layer를 적용한 GZO 박막을 전면전극으로 이용하여 DSC를 제작하여 효율을 확인하였다. 2wt%의 $Ga_2O_3$가 도핑된 ZnO 박막은 20mTorr 400$^{\circ}C$에서 Pulsed Laser Deposition (PLD)에 의해 성장되었고, $TiO_2$박막은 Ti 금속을 타겟으로 이용하여 30mTorr 400$^{\circ}C$에서 증착되었다. Scanning electron microscopy (FE-SEM)을 이용한 박막 분석 결과 $TiO_2$가 증착된 GZO 박막의 경우 표면 파괴가 일어나지 않았다. Solar Simulator을 이용하여 I-V특성 측정결과 상용 FTO를 사용한 DSC 수준의 효율을 나타내었다. 이에 따라 Pulsed Laser Deposition을 이용해 제작된 GZO 기판은 $TiO_2$ Blocking Layer를 이용하여 표면 파괴를 방지할 수 있었으며, 이는 향후 염료감응형 태양전지의 투명전극에 적용 가능 할 것으로 판단된다.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.1017-1019
• /
• 1998

In this paper, the fabrication of a micropump with two giant magnetostrictive films of Sm-Fe and Tb-Fe is presented. The pump consist of one silicon wafer and one cover glass. The micropump consists of an actuator diaphragm, a paired nozzle and diffuser, and two through holes. The Structure of the micropump is fabricated by the chemical vapor deposition, the etching and the sputtering of the magnetostrictive films. The deflection of the actuator measured diaphragm is measured by using the laser vibrometer and the flow rate of the micro pump is observed by using a video microscope.