• Proceedings of the KIEE Conference
• /
• 1989.11a
• /
• pp.224-227
• /
• 1989

In this paper, The implementation of modular neural net for fault diagnosis in power system is presented. Until now, there have been many researches on expert system for fault diagnosis. On expert system, a lot of time for searching goal is needed. But, neural net processes with high speed, as it has parallel distributed processing structure. So neural net has good performance in on-line fault diagnosis. For fault diagnosis in large power system, the constitution of modular neural net with partition of large power system is presented.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.53 no.7
• /
• pp.397-404
• /
• 2004

This paper describes a study of transient characteristics in 765kV untransposed transmission lines. As the 765(kV) system can carry bulk power, some severe fault on the system nay cause large system disturbance. The large shunt capacitance and small resistance of 765kv transmission line make various difficulties for its protection. These problems including current difference between sending and receiving terminals on normal power flow, low order harmonic current component in fault current and current transformer saturation due to the long DC time constant of the circuit etc. must be investigated and solved. The analysis of transient characteristics at sending terminal has been carried out for the single phase to ground fault and 3-phase short fault, etc. The load current, charging current in normal condition and line flows, fault current, THD(Total Harmonic Distortion) of harmonics, time constants have been analysed for the 765kV untransposed transmission line systems.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.2
• /
• pp.102-108
• /
• 2008

AC generator plays an important role of power system. The large AC generator fault may lead to large impacts or perturbations in power system. And then the protection of a generator has very important role in maintaining stability in a power system. In present, the DFT(discrete Fourier transform) based RDR(ratio differential relay) had been widely applied to a internal fault of a generator stator winding. But DFT has a serious drawback. In the course of transforming a target signal to frequency domain, time information is lost. DWT uses a time-scale region. This paper proposes an advanced fault detection algorithm using DWT(discrete Wavelet transform) to enhance the drawback of conventional DFT based relaying. To evaluate the performance of the proposed relaying, we used the test data which were sampled with 720 [Hz] per cycle and obtained from ATP(alternative transient program) simulation. And we made a comparative study of conventional DFT based RDR and the proposed relaying.

• Journal of Internet Computing and Services
• /
• v.3 no.5
• /
• pp.31-39
• /
• 2002

A rapid growth of internet and sudden increase of multimedia data demands for high-speed transfer media and if optimizec usage from the interface system. To achieve this level of network bandwidth, multiple NICs for support of high-speed network bandwidth have been developed and studied. Furthermore, the use of multiple NICs can provide high-speed LAN environment without large network environment modification, supports backward compatibility of current system and reduce overhead. However. if system failure is caused by SPOF(Single Point of Failure) fault of large-capacity multiple NICs, incredible loss will be met because it services large capacity of multimedia data, Therefore, to prevent loss coming from faults, we describe 'Fault tolerance of multiple NICs', which use the fault prevention mechanism. Considering inefficiency of availability and serviceability that is occurred with existing TMR, Primary-Standby approach and Watchdog time mechanism, we propose and design the efficient fault tolerance mechanism, which minimize down time as changing of detection period dynamically. Consequently, the fault tolerance mechanism proposed for reducing overhead time when the fault is occurred, should minimize system downtime overall.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.64 no.4
• /
• pp.291-296
• /
• 2015

Transmission line is exposed to a large area, and then faults are likely to occur than the other component of power system. When a fault occurs on a transmission line, fault locator helps fast recovery of power supply on power system. This paper deals with the design of a digital fault locator for improvement accuracy of the fault distance estimation and a fault occurrence position for transmission line. The algorithm of a fault locator uses a DC offset removal filter and DFT filter. The algorithm utilizes a fault data of GPS time synchronized. The computed fault information is transmitted to the other side substation through communication. The digital fault locator includes MPU module, ADPU module, SIU module, and a power module. The MMI firmware and software of the fault locator was implemented.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.6
• /
• pp.2240-2248
• /
• 2015

The integration of the large-scale wind power brings great challenge to the stability of the power grid. This paper investigates and studies the fault on May 14, 2012 of the large-scale cascading trip-off of wind turbines in North China. According to the characteristics of the voltage variation, the fault process is divided into three stages: the pre-event stage, the critical stage before cascading, and the cascading stage. The scenes in the fault are reproduced, using the full-size actual power system model. Simulation models of double-fed induction generators (DFIGs) and SVCs including protection settings and controller strategies are carefully chosen to find out the reason of voltage instability in each stage. Some voltage dynamic that have never been observed before in the faults of the same kind are analyzed in detail, and an equivalent voltage sensitive dynamic model of DFIG is proposed for the fast computation. The conclusions about the voltage dynamics are validated by the actual PMU observation evidence.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.20 no.1
• /
• pp.15-20
• /
• 2010

In this paper, we discuss a decentralized observer design problem for the fault detection in the large-scale continuous-time T-S (Takagi-Sugeno) fuzzy system. Since the fault detection residual is desired to be as sensitive as possible, on the fault, we use $\mathfrak{H}_-$ index performance criterion. Sufficient conditions for the existence of such a observer is presented in terms of linear matrix inequalities. Simulation results show the effectiveness of the proposed method.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2003.09a
• /
• pp.28-35
• /
• 2003

Quaternary faults found around the Ulsan Fault System can be divided into 4 types based on the fault outcrop features : Type I fault cuts basements and Quaternary deposits of which remain on both hangwall and footwall. Type II fault is developed only in Quaternary deposit. Type III fault has inclined unconformity after Quaternary faulting. Type IV fault is common type around the Ulsan fault system and has horizontal unconformity surface after cutting earlier Quaternary deposit. After erosion, later Quaternary deposit overlays on both old deposit and basement. The Ulsan Fault System consists of three segments at large scale from north to south based on the lineament rank and shape, Quaternary fault location, and slip rate. The segment boundaries are identified by the existence of the two intervals which show no lineaments and Quaternary faults. But, if detail fault parameters could be obtained and used in segmentation, it can be divided into more than three segments.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.6
• /
• pp.1128-1133
• /
• 2011

In a wind farm, a large number of small wind turbine generators (WTGs) operate whilst a small number of a large generator do in a conventional power plant. To maintain high quality and reliability of electrical energy, a wind farm should have equal performance to a thermal power plant in the transient state as well as in the steady state. The wind farm shows similar performance to the conventional power plant in the steady state due to the advanced control technologies. However, it shows quite different characteristics during fault conditions in a grid, which gives significant effects on the operation of a wind farm and the power system stability. This paper presents an analysis of response of a wind farm during grid fault conditions. During fault conditions, each WTG might produce different frequency components in the voltage. The different frequency components result in the non-fundamental frequencies in the voltage and the current of a wind farm, which is called by "beats". This phenomenon requires considerable changes of control technologies of a WTG to improve the characteristics in the transient state such as a fault ride-through requirement of a wind farm. Moreover, it may cause difficulties in protection relays of a wind farm. This paper analyzes the response of a wind farm for various fault conditions using a PSCAD/EMTDC simulator.

• Progress in Superconductivity and Cryogenics
• /
• v.9 no.1
• /
• pp.37-42
• /
• 2007

We are developing a 22.9 kV/25 MVA superconducting fault current limiting(SFCL) system for a power distribution network. A Bi-2212 bulk SFCL element, which has the merits of large current capacity and high allowable electric field during fault of the power network, was selected as a candidate for our SFCL system. In this work, we experimentally investigated important characteristics of the 190 kVA Bi-2212 SFCL element in its application to the power grid e.g. DC voltage-current characteristic, AC loss, current limiting characteristic during fault, and so on. Some experimental data related to thermal and electromagnetic behaviors were also compared with the calculated ones based on numerical method. The results show that the total AC loss at rated current of the 22.9 kV/25 MVA SFCL system, consisting of one hundred thirty five 190 kVA SFCL elements, becomes likely 763 W, which is excessively large for commercialization. Numerically calculated temperature of the SFCL element in some sections is in good agreement with the measured one during fault. Local temperature distribution in the190 kVA SFCL element is greatly influenced by non-uniform critical current along the Bi-2212 bulk SFCL element, even if its non-uniformity becomes a few percentages.