• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.2
• /
• pp.125-131
• /
• 2017

In order to develop test and performance analysis techniques for a CRP propulsion, a CRP dynamometer which can be installed inside the model ship was designed and manufactured. The object ship was the 16000TEU container carrier, which has test results for the single propeller. The design concept of the present CRP is that forward & after propellers have the same power ratio and their RPM ratio is 0.75:1. To begin with, we checked the performance of the CRP dynamometer through the calibration and then installed it inside the model ship. After the model ship setup including the design CRP and the rudder in the Large Cavitation Tunnel(LCT), a series of model tests composed of power ratio check, propeller behind wake(PBW) test, cavitation observation and pressure fluctuation tests was conducted. Through the model test and data analysis for CRP, the experimental technique was established and the improved method for CRP design was suggested.

• Journal of KSNVE
• /
• v.9 no.1
• /
• pp.206-213
• /
• 1999

In the beam-like ship vibration analysis. three-dimensional correction factor(J-factor) can be calculated by considering the three-dimensional effect of the two-dimensional added mass. However, existing method is time-consuming with low accuracy in respect of global vibration analyses for vessels with large breadth. In this paper, to improve the demerit of the previous method, a new method of the beam-like ship vibration analysis is introduced In this method. the three-dimensional fluid added mass of surrounding water is calculated directly by solving the velocity potential problem using the Boundary Element Method (BEM). Then the three-dimensional added mass is evaluated as the lumped mass for each strip. Also, the beam-like ship vibration analysis for the structural beam model if performed with the lumped mass considered. It was verified that this new method is useful for the beam-like ship vibration analysis by comparing results obtained from both the existing method and the new method with experimental measurements for the open top container model.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.1
• /
• pp.37-44
• /
• 2018

To understand the dynamic characteristics of the vessel with hydroelastic response, it is very important to estimate the dynamic modal parameters such as mode shapes, natural frequency, and damping ratio. These dynamic modal parameters of full scale ship are a priori unknowns, hence to be estimated directly based upon the full scale measurement data. In this paper, dynamic modal parameters were extracted by signal processing of acceleration and strain data measured from a large container ship whose loading capacity is 9400TEU. The mode shapes of the vibrating hull were identified using the proper orthogonal decomposition and the vibration response of hull was decomposed into its modal magnitudes. Natural frequencies of specific modes were derived via Fourier transform of these modal magnitude. Also, the free decay signal of the vibrating hull was obtained through the random decrement technique and the damping ratio was estimated with accuracy.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.6
• /
• pp.789-797
• /
• 2021

The worldwide sizes of container ships are rapidly increasing. The container ship size in 2005, which was about 9,200 TEU has increased to 24,000 TEU in recent times. In addition to the increase in the sizes of the container ships, the arrivals/departures of large container vessels to/from Korea have also increased. Hence, the necessity for reviewing safe passage of such vessels is emphasized. In the present study, a 24,000 TEU container vessel was used as a model ship to calculate the under-keel clearance (UKC) at Gadeok Channel through which vessels must pass to arrive at Busan New Port, in accordance with the Korean Port and Fishing Port Design Standards and Commentary. In addition, the maximum allowable speed that meets UKC standards was calculated using various squat formulas, whose results were then compared with the current speed limit standards. The analysis results show that Busan New Port requires 10% marginal water depth, and the squat that meets this requirement is 0.95 m. Gadeok Channel requires 15% marginal water depth, and the squat that meets this requirement is 1.78 m; in this case, the maximum allowable speed is calculated as 15 kts. Busan New Port has set the speed limit as 12 kts, which is higher than the calculated 11 kts. Thus, speed limit reconsideration is required in terms of safety. However, the set speed limit for Gadeok Channel is 12 kts, which is lower than the calculated 15 kts. Thus, additional considerations may be provided to increase the speed limits for smooth navigational passage of vessels. The present study, however, is constrained by the fact that it reflects only a limited number of elements in the UKC and allowable speed calculations; therefore, more accurate UKC and safe speed values can be suggested based on extended studies to this research.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2017.10a
• /
• pp.80-87
• /
• 2017

This paper is related to structural assessment considering the hydroelastic response of ultra large container ships, especially from whipping (bow or stern impacts) and from springing (resonance). In general, whipping contributes both to increased fatigue and extreme loading, while springing does mainly contribute to increased fatigue loading. To evaluate the hydroelastic response quantitatively with high accuracy, numerical code considering hydro-structure coupling was applied and fatigue strength of a 13,100 TEU class containership was verified. The segmented model test and full scale measurement were also needed to assess the effect of whipping and springing on the fatigue and extreme capacity in more realistic way and for verification of the numerical tools. With reference to class rule, fatigue assessment considering springing effect and extreme assessment considering whipping effect were introduced.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2013.12a
• /
• pp.42-46
• /
• 2013

Recently, according to the growth of demand about large container carrier, the studies for cavitation of semi-spade rudder were increased. In spite of many effort to solve, the fundamental solution can not be found. So, the studies for full-spade rudder are increasing to solve. In Pusan national university, the studies for full-spade twisted rudder and full-spade wavy twist rudder were carried out. However, most studies are carried out in numerical analysis and the many studies of experimental comparison between each rudder are not exist. This paper describe design history of full-spade rudder (twist rudder, wavy twist rudder) for KCS (KRISO Container Ship) and compare performance of each designed full-spade rudder about resistance and self-propulsion with conventional rudder (semi-spde rudder). The measurement about designed rudder's rudder force will be performed near future.

• Proceedings of KOSOMES biannual meeting
• /
• 2004.05b
• /
• pp.107-112
• /
• 2004

In order to improve the safety r! ship berthing and the efficiency r! berth operation in the harbour, the berthing energy acting on a ship in berthing maneuver need to be estimated properly. The berthing energy is used as one q the criteria to determine the maximum permissible load of fender as well as important factors to establish the berthing speed and the required power r! tug-beat for pilot and ship operator. In this study, some problems r! present the method of berthing energy are discussed on the basis of the hydrodynamic aspects. Then, series calculations of berthing energy are carried out considering the effect of water depth on added mass and the ship shape for container series from 1,600TEU to 12,000TEU.

• Journal of Navigation and Port Research
• /
• v.27 no.1
• /
• pp.49-54
• /
• 2003

Recently, mega-float offshore structure is studied as of the effective utilization of the ocean space. And mega-float structure are now being considered for various applications such as floating airports. container yard, offshore cities and so on. This mega-float structure is relatively flexible compared with floating structures like large ship. When we estimate dynamic responses of these structures in waves, the elastic deformation is important, because vertical dimension is small compare with horizontal. the analysis of the dynamic reponses as it receive regular wave is studied. The finite element method is used in the analysis of structural section of this model. And the analysis is carried out using the boundary element method in the fluid division. In oder to know the characteristics of the dynamic response of the mega-float structures, effects of wavelength, water depth, and wave direction on the dynamic response of the floating structure are studied by use of numerical calculation.

• Korea Trade Review
• /
• v.45 no.5
• /
• pp.141-159
• /
• 2020

Container terminals at Gwangyang Port are operated by three container operators: A, B and C. Ultimately, there is consensus that a single operator should operate all terminals so that economies of scale can be achieved even in the operation of the container terminal. Integration between operators has a positive effect on both operators and shipping companies. From the operator's point of view, overlapping fixed costs between operators can be unified, reducing overall costs and utilizing spare facilities. On the other hand, from the viewpoint of the shipping company, it is possible to ensure stable use of the port facilities and always allow berthing, reduce days on demurrage and ship waiting, and provide one-stop service for work. However, existing cases of operators' integration or relocation of terminals remained to estimate the expected effects of alternatives, emphasizing only the financial point of view. The port terminal is a large system, and it is important to consider that it is an aggregate of major logistics facilities and equipment. Moreover, if the estimation can be made by quantifying the expected effect, the justification of the terminals' relocation can be further emphasized. Therefore, it is very important to estimate the expected effect from the viewpoint of systemic operation. Moreover, the need for operators' integration can be further emphasized if it can be estimated through quantification of expected effects. Currently, three alternatives are considered as alternatives to the terminals' relocation, and in this study, the optimal plan was derived for the 3 alternatives by the linear planning model of the minimum shuttle transportation cost in the terminal. The optimal plan is alternative 2, which shows the most advantageous integration effect in terms of expected effects. Alternative 2 integrates the B terminal into the C terminal, and the A terminal operates independently as it is.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.2
• /
• pp.195-200
• /
• 2015

It is envisaged that the effect of increasingly stricter air emissions legislation implemented through IMO Annex VI and other local air quality controls, together with favorable financial conditions for the use of natural gas instead of liquid fuel oil as a bunker fuel, will see an increasing number of DF engine and single gas fuel engine applications to LNG carriers and other vessel types. As part of provision for the current international movements in the shipping industry to reduce GHG emission in air, new design concepts using natural gas as an alternative fuel source for propulsion of large commercial vessels, have been developed by shipyards and research institutes. In this study, an explosion analysis for a gas supply machinery room of LNG-fuelled container ship is presented. The gas fuel concept is employed for the high pressure ME-GI where a leakage in the natural gas double supply pipe to the engines is the subject of the present analysis. The consequences of a leak are simulated with computational fluid dynamics (CFD) tools to predict typical leak scenarios, gas cloud sizes and possible explosion pressures. In addition, capacity of the structure which is subject to explosion loads has been assessed.