• Journal of the Korean Institute of Gas
• /
• v.11 no.2 s.35
• /
• pp.37-42
• /
• 2007

This paper presents the leakage safety of two O-rings, which are located at the rectangular groove between a valve body and a valve stem. The leakage safety analysis of 0-ring seals has been computed as functions of a compression set and a liquefied petroleum gas pressure of a LPG cylinder using a FEM program, MARC. The FEM computed results indicate that the loads from the filling pressure of $8kg/cm^2$ to the upper limit of the safety valve, $24.8kg/cm^2$ work safely according to the pressure vessel code. But two O-rings should consider the aging effects for an increased safety of the o-ring.

• Journal of the Korean Institute of Gas
• /
• v.5 no.2 s.14
• /
• pp.22-29
• /
• 2001

The number of gas containers and the period of exchanging gas containers are vsy important in designing liquefied petroleum gas(LPG) supply system for small capacity domain. And also the evaluation of remaining LPG in containers to be exchanged is very useful information in commerce. However seldon has been studied on calculating method about those with respect to gas consumption pattern. In this study, a simulation method was developed to estimate the evaporation capacity of LPG container, the mass gas flow rate from LPG container, the temperature and vapor pressure of LPG, and the remained LPG at containers to be exchange by using LPG property equations, mass balance equation, and heat balance equation. The simulation results were correlated well with experimental data. The overall heat transfer coefficient from air to LPG is approximately $9{\~}13 kcal/m^2{\cdot}hr{\cdot}^{\circ}C$ and does not strongly affect on the evaporation capacity of LPG container. The mass gas flow rate from LPG container is constant when the vapor pressure of LPG is within pressure regulator's control range. While, out of range, it suddenly reduce to a evaporation rate which is balanced with heat transfer from air. The evaporation capacity of LPG container increased with surrounding temperature and the composition of propane, and decreased drastically with continuous gas consumption. The number of gas containers divided the number of houses using gas supply system was reduced by using automatic gas feeding device.

• Plant Journal
• /
• v.9 no.4
• /
• pp.31-36
• /
• 2013

In order to extend a hot gas parts replacement cycle of a gas turbine, blade row 1 from low pressure turbine, which has a significant impact on the cycle, has been selected from stored set after one cycle use. Taking into account the status of the first stage moving blade in LP turbine operated more than 27,000 equivalent operating hours(EOH) and the replacement cycle in the same type of gas turbine, the replacement of the high temperature components installed on the GT, a study subject, can be extended from 24,000 to 27,000 EOH.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.734-737
• /
• 2004

The metal-ferroelectric-semiconductor (MFS) structure is widely studied for nondestructive readout (NDRO) memory devices, but conventional MFS structure has a critical problem. It is difficult to obtain ferroelectric films like PZT on Si substrate without interdiffusion of impurities such as Pb, Ti and other elements. In order to solve these problems, the metal-ferroelectric-insulator-semiconductor (MFIS) structure has been proposed with a buffer layer of high dielectric constant such as MgO, $Y_2O_3$, and $CeO_2$. In this study, the etching characteristics (etch rate, selectivity) of MgO thin films were etched using $Cl_2/Ar$ plasma. The maximum etch rate of 85 nm/min for MgO thin films was obtained at $Cl_2$(30%)/Ar(70%) gas mixing ratio. Also, the etch rate was measured by varying the etching parameters such as ICP rf power, dc-bias voltage, and chamber pressure. Plasma diagnostics was performed by Langmuir probe (LP) and optical emission spectroscopy (OES).

• Journal of the Korean Institute of Gas
• /
• v.24 no.6
• /
• pp.1-10
• /
• 2020

Reactivity controlled compression ignition (RCCI) combustion is one of dual-fuel combustion systems which can be constructed by early diesel injection during the compression stroke to improve premixing between diesel and air. As a result, RCCI combustion promises low nitrogen oxides (NOx) and smoke emissions comparing to those of general dual-fuel combustion. For this combustion system, to meet the intensified emission regulations without emission after-treatment systems, exhaust gas recirculation (EGR) is necessary to reduce combustion temperature with lean premixed mixture condition. However, since EGR is supplied from the front of turbocharger system, intake pressure and the amount of fresh air supplementation are decreased as increasing EGR rate. For this reason, the effect of various EGR rates on the brake power and thermal efficiency of natural gas/diesel RCCI combustion under two different operating conditions in a 6 L compression ignition engine. Varying EGR rate would influence on the combustion characteristic and boosting condition simultaneously. For the 1,200/29 kW and 1,800 rpm/(lower than) 90 kW conditions, NOx and smoke emissions were controlled lower than the emission regulation of 'Tier-4 final' and the maximum in-cylinder pressure was 160 bar for the indurance of engine system. The results showed that under 1,200 rpm/29 kW condition, there were no changes in brake power and thermal efficiency. On the other hand, under 1,800 rpm condition, brake power and thermal efficieny were decreased from 90 to 65 kW and from 37 to 33 % respectively, because of deceasing intake pressure (from 2.3 to 1.8 bar). Therefore, it is better to supply EGR from the rear of compressor, i.e. low pressure EGR (LP-EGR) system, comparing to high pressure EGR (HP-EGR) for the improvement of RCCI power and thermal efficiency.

• Journal of Korean Institute of Industrial Engineers
• /
• v.10 no.2
• /
• pp.17-27
• /
• 1984

This paper is concerned with a branched pipe network system which transports some fluids or gas from multiple sources to multiple demand nodes. A nonlinear programming model is proposed for determining junction locations simultaneously with selection of pipe sizes and pump capacities such that the capital and operating costs of the system are minimized over a given planning horizon. To solve the model, a hierarchical decomposition method is developed with the junction location being the primary variable. With some values fixed for the primary, the other decision variables are found by linear programming. Then, using the postoptimality analysis of LP, junction locations are adjusted. We repeat this process until an optimum is approached. A simple example of designing a water distribution network is solved to illustrate the optimization procedure developed.

• Journal of Environmental Health Sciences
• /
• v.17 no.2
• /
• pp.9-16
• /
• 1991

Personal NO$_{2}$ expousre and time activity patterns were measured during March, 1991 for 46 taxi drivers in the Seoul area. Badge-type personal samplers were worn for 24 hours by taxidrivers for monitoring personal expousre to NO$_{2}$. A standard respiratory questionnaire was administered and pulmonary function test was performed using a protable spirometry. The mean concentrations of personal NO$_{2}$ expousres of taxi drivers were 0.55ppm. Personal NO$_{2}$ exposures of taxi drivers were seemed to be higher in longer period of driving, smokers, and use of LP gas in homes. Prevalence rate of respiratory symptoms and the level of pulmonary function(FEV$_{1.0}$ and FVC) seemed to be related to higher personal NO$_{2}$ concentrations. It is concluded that persoanl NO$_{2}$ expousres of taxi drivers are probably affected by indoor NO$_{2}$ levels of a tax/and their common activities.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.04a
• /
• pp.96-103
• /
• 2000

This research is a new design method, which will be presented as a basic concept for a more efficient minimum weight design of grillages, as an attempt to describe true collapse mechanism in as overall search as possible. It serves as introduction to the numerical technique of Linear Programming(LP) and Automatic Modified Direct Plastic Frame Analysis(AMDPFA). Attention is directed to both analysis and design, and emphasis is placed on the physical significance of Systematic Searching Techniques(SST) involved. In weight minimum grillages design, the parameterisation study in optimum beam configuration which was carried out over the range of beam sections for a given plastic section modulus likely to occur in structures by suing an adaptive stochastic optimisation technique, Genetic Algorithms.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.5
• /
• pp.654-661
• /
• 1999

This is fundamental study to improve performance of the SI engine,. In this study a conven-tional kerosene engine was modified to LPG dedicated engine which can be operated with LPG(Liquefied Petroleum Gas) The modified model were tested in accordance with various compression ratios. Also the engine performance with modified model was compared with the conventional one. The results are sum-marized as follow; 1. In comparison with the conventional kerosene Gasoline engine and LPG dedicated engine can be operated with lower exhaust emission better fuel economy and better thermal efficiency. 2. But is produce a slightly lower brake horse power.

• Journal of Energy Engineering
• /
• v.14 no.4 s.44
• /
• pp.268-276
• /
• 2005

Vacuum Residue (VR) combustion tests were carried out with a 20 kg/hr (fuel feed rate) small scale reactor. The nozzle used was a steam atomized, internal mixing type. Compared to heavy oil, vacuum residue used in this work is extremely high viscous and contains high percentages of sulfur, carbon residue and heavy metals. To ignite atomized VR particles, it was necessary to preheat the reactor, and it has been done with LP gas. The axial and radial gas temperature, major species concentrations and solid sample were analyzed when varying the fuel feed rate. The main reaction zone of atomized VR-air flame in a reactor was anticipated within about 1 m from the burner tip by considering the profiles oi gas temperature, species concentration and particle size measured along with the reactor. At downstream, the thermally, fully developed temperature distribution was obtained. SEM photographs revealed that VR carbon particles collected from the reactor are porous and have many blow-holes on the particle surface.