• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.05a
• /
• pp.79-84
• /
• 1993

This paper describes the development of lithium rechargeable cell. $LiCoO_2$ is recently recognized as a suitable cathode active material of a high voltage, high energy lithium rechargeable batteries because $Li^+$ ion can be electrochemically deintercalated/intercalated from/to $Li_xCoO_2$. The transition metal oxide of $LiCoO_2$ was investigated for using as a cathode active material of 4V class Li rechargeable cell. $LiCoO_2$ cathode was prepared by using a active material of 85 wt%, graphite powder of 12 wt% as a conductor and poly-vinylidene fluoride of 3 wt% as a binder. The electrochemical and charge/discharge properties of $LiCoO_2$ were investigated by cyclic voltammetry and galvanostatic charge/discharge. The open circuit voltage of prepared $LiCoO_2$ electrode exhibited approximately. potential range between 3.32V and 3.42V. During the galvanostatic charge/discharge, $LiCoO_2/Li$ cell showed stable cycling behavior at scan rate of 1mV/sec and potential range between 3.6V and 4.2V. Also its coulombic efficiency as function of cycling was 81%~102%. In this study the $LiCoO_2/Li$ cell showed the available discharge capacity of 90.1 mAh/g at current density of $1mA/cm^2$ and cell discharge voltage range between 3.6V~4.2V.

• Journal of the Korean Ceramic Society
• /
• v.32 no.4
• /
• pp.507-515
• /
• 1995

The monolithic dry gels of the Li2O-Al2O3-TiO2-SiO2 system were prepared by the sol-gel technique using metal alkoxides as starting materials to obtain monolithic glass-ceramics at low temperature without melting. Activation energy for the crystal growth of the gel with 6.05% TiO2, nucleating ageng, for the preparation of Li2O-Al2O3-TiO2-SiO2 system glass-ceramic was 101.14kcal/mol. As a result of the analysis of DTA & XRD, it was confirmed that the crytallization of Li2O-Al2O3-TiO2-SiO2 system glass-ceramic was the most efficient when 6.05% TiO2, nucleating agent, was added. $\beta$-eucryptite solid solution crystals and $\beta$-spodumene solid solution crystals were detected in the sample heat treated above 85$0^{\circ}C$. The sintered gel heat treated at 85$0^{\circ}C$ had the specific surface area of 185$m^2$/g, the pore volume of 0.19cc/g and the average pore radius of 20.8$\AA$. This shows that the sintered gel is also comparatively porous material. In temperature range of 25~85$0^{\circ}C$ thermal expansion coefficient of the specimen which was crystallized for 10hrs at 85$0^{\circ}C$ was 6.7$\times$10-7/$^{\circ}C$, which indicated that the crystallized specimen was turned out to be the glass-ceramic with low thermal expansion.

• Transactions of the Korean hydrogen and new energy society
• /
• v.13 no.4
• /
• pp.259-269
• /
• 2002

A battery based on the lithium/elemental sulfur redox couple has the advantage of high theoretical specific capacity of 1,675 mAh/g-sulfur. However, Li/S battery has bad cyclic durability at room temperature due to sulfur active material loss resulting from lithium polysulfide dissolution. To improve the cycle life of Li/S battery, PEGDME (Poly(ethylene glycol) dimethyl ether) 500 containing 1M LiTFSI salt which has high viscosity was used as electrolyte to retard the polysulfide dissolution and nano-sized $Mg_{0.6}Ni_{0.4}O$ was added to sulfur cathode as additive to adsorb soluble polysulfide within sulfur cathode. From experimental results, the improvement of the capacity and cycle life of Li/S battery was observed( maximum discharge capacity : 1,185 mAh/g-sulfur, C50/C1 = 85 % ). Through the charge-discharge test, we knew that PEGDME 500 played a role of preventing incomplete charge-discharge $behavior^{1,2)$. And then, in sulfur dissolution analysis and rate capability test, we first confirmed that nano-sized $Mg_{0.6}Ni_{0.4}O$ had polysulfide adsorbing effect and catalytic effect of promoting the Li/S redox reaction. In addition, from BET surface area analysis, we also verified that it played the part of increasing the porosity of sulfur cathode.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.11
• /
• pp.91-99
• /
• 1998

A 5Gbps LiNbO$_3$ optical phase modulator was designed, packaged and it's properties were characterized for optical communications. The APE(annealed proton exchange) method was employed for the optical waveguide and the electrode of ACPS (asymmetric coplanar strip) type was formed by electro-plating on LiNbO$_3$ for applying microwave signal with a dimension of width 18${\mu}{\textrm}{m}$, gap 9${\mu}{\textrm}{m}$ and length 50mm. The fabricated single-moded modulator operated at a 1550nm wavelength exhibits its modulation bandwidth, insertion loss and driving voltage of 7㎓, 3.0dB and 6V, respectively.

• Journal of Sensor Science and Technology
• /
• v.11 no.6
• /
• pp.371-377
• /
• 2002

$Y_2O_3:Eu^{3+}$ and Li-doped $Y_2O_3:Eu^{3+}$ thin films have been grown on sapphire substrates using a pulsed laser deposition technique. The thin film phosphors were deposited at a substrate temperature of $600^{\circ}C$ under the oxygen pressure of 100, 200 and 300 mTorr. The films grown under different deposition conditions have been characterized using microstructural and luminescent measurements. The crystallinity and photoluminescence (PL) of the films are highly dependent on the oxygen pressure. The PL brightness data obtained from $Y_2O_3:Eu^{3+}$ films grown under optimized conditions have indicated that sapphire is one of the most promising substrate for the growth of high quality $Y_2O_3:Eu^{3+}$ thin film red phosphor. In particular, the incorporation of $Li^{+}$ ions into $Y_2O_3$ lattice could induce a remarkable increase of PL. The highest emission intensity was observed with LiF-doped $Y_{1.84}Li_{0.08}Eu_{0.08}O_3(Y_2O_3LiEu)$, whose brightness was increased by a factor of 2.7 in comparison with that of $Y_2O_3:Eu^{3+}$ films. This phosphor may promise for application to the flat panel displays.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.6
• /
• pp.517-523
• /
• 2008

The microwave dielectric properties of $LiNb_3O_8-TiO_2$ based ceramics with low firing agents, CuO, $Bi_2O_3$, $B_2O_3$, $SiO_2$, $TiO_2$, were investigated to improve the sintering condition for the LTCC system. According to the X-ray diffraction and SEM, the ceramics of $LiNb_3O_8-TiO_2$ with low firing agents showed no significant second phases within a range of experiments, and fine microstructures. By adding the low firing agents, the sintering temperature decreased from $1200^{\circ}C$ to $925^{\circ}C$. Based on the results of electrical measurements, the $LiNb_3O_8-TiO_2$ ceramics showed a promising microwave dielectric properties for LTCC applications, those are ${\varepsilon}_r$ (dielectric constant) = 44, Q f (quality factor) = 18000, and ${\tau}_f$ (the temperature coefficient of resonant frequency) = $-1.5\;ppm/^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 2001.11b
• /
• pp.106-108
• /
• 2001

As 3V cathode material, a new doping spinel material, LiMn1.6Se0.4O4 powder with a phase-pure polycrystalline was synthesized by a sol-gel method. In spite of Jahn-teller distortion in 3V region($2.4{\sim}3.5V$), the LiMn1.6Se0.4O4 electrode shows no capacity loss. The material in the 3V region initially delivers a discharge capacity of 100mAh/g which increase with cycling to reach 105mAh/g after 90cycles. And 5V cathode material LiNi0.5-xMxMn1.5O4(M=Cr, V, Fe) compounds have been synthesized by sol-gel method. a series of electroactive spinel compounds, LiNi0.5-xMxMn1.5O4(M=Cr, V, Fe) has been studied by crystallographic and electrochemical methods. The material presents only one plateau at around 4.5 V vs. Li/Li+ with a large discharge capacity of 152mAh/g and fairly good cyclability.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.5 no.1
• /
• pp.206-217
• /
• 2001

The purpose of this study was to estimate that the relations of weathering speed and shear strength of granite soil by tracing the weathering depth of granite soil from the very moment of its cutting. The results obtained this follows ; 1) The relationships among Nc, Li and CEC, Li>6%, CEC>14 corresponds to Nc=2~30, and 4%${\phi}$)increases at a standard pressure. 3) And Nc=0~50 corresponds to $27{\sim}50^{\circ}$ of internal fiction angle and to 12~49kPa of cohesion. That is to say, internal friction angle(${\phi}$)corresponds better than cohesion(c). In conclusion, this study suggests that in simplified dynamic cone penetration test a penetration boundary line of 5 centimeters is decided at around Li=4%, CEC=3(meq/100g) which is classified as a completely weathering soil. It also appears that CEC increases as Li increases while Nc decreases.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.3
• /
• pp.267-272
• /
• 1999

Micro-defects in the undoped and MgO-doped $LiNbO_3$ single crystals, which were grown from a congruent melting composition (48.6 mol% $Li_2$O) by the CZ (Czochralski) method, were analyzed using microscopic techniques such as optical microscopy (OM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Effects of the dopant and g value (the fraction solidfied) on the domain structure and micro-defect were investigated to build a corelationship with a growth condition of crystal. It was observed that the micro-defect concentrated near the domain wall is caused by high stress. Especially, the micro-defect was observed to be biased toward a certain side of the domain wall.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.1
• /
• pp.27-32
• /
• 2011

In this study, we have investigated the power conversion efficiency of organic solar cells utilizing conjugated polymer/fullerene bulk-hetero junction(BHJ) device structures. We have fabricated poly(3-hexylthiophene)(P3HT), poly[2methoxy-5-(3',7'-dimethyloctyl-oxy)-1-4-phenylenevinylene] as an electron donor, [6,6]-phenyl $C_{61}$ butyric acid methylester(PCBM-$C_{61}$)as an electron acceptor, and poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate)(PEDOT:PSS) used as a hole injection layer(HIL), after fabricated active layer, between active layer and metal cathode(Al) deposited LiF interlayer(5 nm). The properties of fabricated organic solar cell(OSC) devices have been analyzed as a function of different thickness. The electrical characteristics of the fabricated devices were investigated by means J-V, fill factor(FF) and power conversion efficiency(PCE). We observed the highest PCEs of 0.628%(MDMO-PPV:PCBM-$C_{61}$) and 2.3%(P3HT:PCBM-$C_{61}$) with LiF inter-layer at the highest thick active layer, which is 1.3times better than the device without LiF inter-layer.