• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.1
• /
• pp.67-75
• /
• 2002

This paper presents a PLD design of Gray Mode Graphic STN LCD drive circuit using PC interface. The proposed LCD drive circuit doesn\`t use microprocessor for the convenience of users. Thus, the LCD drive circuit can transfer efficiently image data created under PC to LCD. The LCD drive circuit which is modelled in schematic capture, AHDL and VHDL is simulated in functionally through the use of ALTERA MAX+PLUS II. Also, timing simulation is performed by ALTERA EPM7192SQC160-15 PLD implementation. The PC interface part have been programmed in MS-Visual C++ 6.0. The validity and efficiency of the proposed LCD drive circuit have been verified by test board. After comparing this LCD drive circuit to specify it was verified that the developed LCD drive circuit showed good performances, such as convenience of users, low cost.

• The KIPS Transactions:PartA
• /
• v.9A no.1
• /
• pp.53-60
• /
• 2002

This paper describes a Gray Mode Graphic STN LCD drive circuit using USB interface. The drive circuit using USB interface can highly transfer image data created under PC t LCD. Hence, the LCD drive circuit doesn't use microprocessor for the convenience of users. The proposed LCD drive circuit part have been verified by simulation and by ALTERA EPF10K10TC144-3 FPGA implementation in VHDL. The USB interface part have been programmed in MS-Visual C++ 6.0. The validity and efficiency of the proposed LCD drive circuit have been verified by test board. After comparing this LCD drive circuit to specify it was verified that the developed LCD drive circuit showed good performances, such as convenience of users, low cost.

• Proceedings of the KIEE Conference
• /
• 2005.11a
• /
• pp.44-47
• /
• 2005

This paper presents the efficient plan for the EMI improvement from of TFT-LCD Module. It investigates the frequency characteristics of Power/Ground Plane of TFT-LCD drive circuit PCB concretely. After the frequency characteristics is reviewed, EMI improvement is tried to insert to RC termination between Power/Ground Plane and to shift resonance frequency. It is confirmed by a simulation result and RC Termination which is inserted the point where the resonance characteristics change is necessary. It applied in 19 "SXGA TFT-LCD drive circuits and the EMI improvement verification is described.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.9
• /
• pp.8-17
• /
• 2012

This paper proposes high performance control of light emitting diode(LED) drive system for liquid crystal display(LCD) backlight. The CCFL(cold cathode fluorescent lamp)was used to a conventional LCD backlight. Due to improvement on luminous efficiency, long life and wide color gamut, LED has gradually substituted for CCFL as backlight. The backlight using LED is necessary to use many LED. For that reason, the LED backlight is using a lot of LED driving circuits. The many LED driving circuit is generated a current deviation between LED. Eventually, it is caused brightness deviation between LED. Therefore, this paper improves the current deviation using transformer and balancing capacitor to solve this problem. Also, for accurate and uniform brightness control, this paper is applied the artificial intelligent control to a dimming control. This paper is compared with conventional system, and validity of this paper proves through that result.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.1
• /
• pp.52-59
• /
• 2010

The conventional CCFL (Cold Cathode Fluorescent Lamp) inverter used in the backlight unit for LCD-TV, composed of the three power stage, can degrade the whole power conversion efficiency. In this paper, a novel scheme to drive the CCFL, composed only of the two power stage without using a dc/dc power stage, is proposed to enhance the whole power conversion efficiency. By adopting the proposed "4-in-1 Transformer", the current balance and the simultaneous ignition among the four CCFL lamp are assured with the one inverter circuit. The proposed scheme features the simple circuit structure, which can save the volume and the cost in the LCD backlight unit. Design considerations are discussed and design procedures are derived. Experimental results of the proposed scheme for 40" LCD-TV are presented to confirm the theoretical analysis.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1211-1213
• /
• 2004

CCFL(cold cathode fluorescent lamp) are used to backlight of LCD(liquid crystal display). CCFL dimming methods are used to pulse frequency modulation(PFM) or pulse width modulation(PWM). In this paper, design of CCFL driving and control circuit by half-bridge type series and parallel resonant inverter that variable frequency modulation method to control the output voltage current. Inverter switching frequency is higher than resonant frequency for stable operating, and it is possible dimming control. On the basis of equivalent circuit, the validity of this study is confirmed by the comparison of simulation and experimental result.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.4
• /
• pp.371-377
• /
• 2006

Cold cathode fluorescent lamps (CCFL) show complex characteristics, which make it difficult to drive them in parallel. In this paper, a multi-lamp driving scheme is proposed to drive multiple lamps for LCD back light to reduce output current unbalance. This propose system is composed of parallel CCFLs, series transformers. The driving system adopts only one backlight inverter to drive multi cold cathode fluorescent lamps (CCFL). Moreover the circuit introduces a multi-lamp driving transformer to reduce lamp-current imbalance. The validity of the proposed scheme is confirmed by the simulated and experimental results.

• Proceedings of the KIEE Conference
• /
• 2008.04c
• /
• pp.125-127
• /
• 2008

기존의 LED(Light Emitting Diode)를 이용한 LCD(Liquid Crystal Display) 백라이트 유닛은 LED에 과전류가 흐르면 소자의 파손이 발생하고 무부하시 불필요한 전력소모가 발생하는 경우가 있어 보호회로가 필요하였다. 그래서 본 논문은 보호회로를 이용한 LCD 백라이트 유닛용의 LED 구동회로를 제안한다. 제안된 보호회로는 2가지로 첫 번째 보호회로는 무부하시 소비전력을 줄이는 보호회로 이다. 시뮬레이션 결과 무부하시 피드백 제어부 IC(Integrated Circuit)의 전원전압 $V_{cc}$를 UVLO(Under Voltage Lock Out)전압 이하로 강하시켰다. 그래서 무부하시 소비되는 전력을 줄일 수 있었다. 두번째 보호회로는 과전류시 보호회로 이다. 시뮬레이션 결과 과전류시 SCR이 온 되어 피드백 제어부 IC의 전원전압 $V_{cc}$를 UVLO전압 이하로 강하시켰다. 따라서 과전류시 LED 동회로 소자의 파손을 방지할 수 있는 장점이 있다.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.906-907
• /
• 2008

기존의 LED(Light Emitting Diode)를 이용한 LCD(Liquid Crystal Display) 백라이트 유닛은 무부하시 불필요한 전력소모가 발생하는 경우가 있어 보호회로가 필요하였다. 그래서 본 논문은 보호회로를 이용한 LCD 백라이트 유닛용의 LED 구동회로를 제안한다. 제안된 보호회로는 실험 결과 무부하시 피드백 제어부 IC(Integrated Circuit)의 전원전압 VCC를 UVLO(Under Voltage Lock Out)전압 이하로 강하시켜 무부하시 소비되는 전력을 줄일 수 있었다. 또, 무부하시 부스트 컨버터 출력부의 전압스트레스를 줄일 수 있었고, 유부하시 보호회로가 있는 컨버터와 보호회로가 없는 컨버터의 효율비교에서 거의 같은 효율이 측정되었다.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.32B no.11
• /
• pp.1374-1382
• /
• 1995

In TFT-LCDs, as the display size area becomes larger, and the resolution higher, we have to consider the image degradation effects due to the incorporation of the TFT-LCD parameters such as the data-line resistance, the common electrode resistance, the data-line to common parasitic capacitance, and the output characteristics of driver ICs. One of the degradation effects is crosstalk resulting from the coupling between the source bus-line and common electrode. Since a source signal which represents a large number of display data is supposed to vary frequently, the common signal level is affected through the coupling effect, resulting in the degradation of nearby pixel drive signals. Therefore, we proposed a method to compensate for this source-common electrode coupling effect, we also designed and experimented the feasibility of our crosstalk compensation circuit in the actual TFT-LCD. We saw that the newly designed compensation circuit greatly reduced the crosstalk in display pattern image.