• Aerospace Engineering and Technology
• /
• v.12 no.2
• /
• pp.156-162
• /
• 2013

In the communication between satellite and ground station, data rate can be determined from the data volume and required transmission time. Increasing data rate can be limited according to the available bandwidth. For the reason, it has been popularly studying on high spectral-efficient modulation scheme in large volume data application such as digital video broadcasting service. This paper presents the conceptual design of UHRIT broadcasting in GEO-KOMPSAT-2A (GK2A) mission by using DVB-S2 standard. Based on the recently determined data rate, UHRIT bandwidth was calculated at the various modulation schemes and code rates of DVB-S2 standard. Receiving performance of global user station was also evaluated thorough link analysis by considering that user station is located at the edge of beam coverage. Finally, maximum data rate was analyzed in a situation that COMS HRIT bandwidth should be alternatively applied for UHRIT downlink.

• Journal of the Korea Society of Computer and Information
• /
• v.19 no.10
• /
• pp.71-79
• /
• 2014

In this paper, the microstrip array antenna is studied to replace the parabolic antenna in the direct satellite reception. A microstrip array antenna has been used in extremely limited area, but if it is applied to practical life like a direct satellite reception antenna, we expect that it will be used in various way. First of all, if we use a microstrip array antenna for a direct satellite reception antenna, it should be guaranteed characteristics of broadband frequency. Therefore, the goal of this paper is designing technique an antenna which guarantees broadband frequency band for a direct satellite reception. In this paper, the proposed microstrip antenna is fed by orthogonal two feed lines to a rectangular patch and a sequentially rotated feeding technique is designed proposed for a good axial ratio in broadband frequency band. The rectangular patch is designed to satellite reception band, and the width and length are W=L=8.9 mm ($0.352{\lambda}o$) respectively. The antenna's ground plane has dimensions of $250{\times}250mm$. The experimental results verify that the proposed antenna had the axial ratio of above 1dB broader than that of the conventional feeding antenna. In order to verify the performance, a $8{\times}8$ array having two pairs was fabricated and tested. The maximum gain is 20.8 dB, the sidelobe level confirm less than -10 dB. It is verified by link budget calculation that C/N=6.7 dB can be obtained for domestic use if this proposed antenna is used in Koreasat reception system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.12
• /
• pp.1375-1382
• /
• 2008

Frequency adjustable D-CRLH(dual-composite right/left handed) transmission lines, which solve the problem of design complexity and uncontrolled frequency of the existing structures, are proposed in this paper. The first design(type I), consisting of defected ground structure(DGS), island pattern in DGS, fixed stub and varactor diodes, controls $C_L$ in the parallel resonant circuit, while the second structure(type 2) composed of fixed DGS, shunt stub and diode adjusts $C_R$ in the series resonant circuit. The dual band frequency points which correspond to the meaningful electrical length of +/-90 degree in the RH/LH region are adjustable according to the bias voltage. The measurement shows that the LH frequency point which has -90 degree of electrical length are adjusted over $4.22{\sim}5.39\;GHz$ and $4.21{\sim}5.05\;GHz$ for type 1 and type 2, respectively, under $1{\sim}12\;V$ of bias voltage. In addition, the frequency Woo where RH turns over LH is controled over $3.26{\sim}4.22\;GHz$ for type 2 with the same bias condition.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.868-882
• /
• 2009

In this paper, channel model and wireless link performance analysis for the short-range wireless communication system applications in the terahertz frequency which is currently interested in many countries will be described. In order to realize high data rates above 10 Gbps, the more wide bandwidths will be required than the currently available bandwidths of millimeter-wave frequencies, therefore, the carrier frequencies will be pushed to THz range to obtain larger bandwidths. From the THz atmospheric propagation characteristics based on ITU-R P.676-7, the available bandwidths were calculated to be 68, 48 and 45 GHz at the center frequencies of 220, 300 and 350 GHz, respectively. With these larger bandwidths, it was shown from the simulation that higher data rate above 10 Gbps can be achieved using lower order modulation schemes which have spectral efficiency of below 1. The indoor propagation delay spread characteristics were analyzed using a simplified PDP model with respect to building materials. The RMS delay spread was calculated to be 9.23 ns in a room size of $6\;m(L){\times}5\;m(W){\times}2.5\;m(H)$ for the concrete plaster with TE polarization, which is a similar result of below 10 ns from the Ray-Tracing simulation in the reference paper. The indoor wireless link performance analysis results showed that receiver sensitivity was $-56{\sim}-46\;dBm$ over bandwidth of $5{\sim}50\;GHz$ and antenna gain was calculated to be $26.6{\sim}31.6\;dBi$ at link distance of 10m under the BPSK modulation scheme. The maximum achievable data rates were estimated to be 30, 16 and 12 Gbps at the carrier frequencies of 220, 300 and 350 GHz, respectively, under the A WGN and LOS conditions, where it was assumed that the output power of the transmitter is -15 dBm and link distance of 1 m with BER of $10^{-12}$. If the output power of transmitter is increased, the more higher data rate can be achieved than the above results.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.4
• /
• pp.9-21
• /
• 2008

In this paper, we propose a GNSS-based RF receiver, A high precision localization architecture, and a high sensitivity localization architecture in order to solve the satellite navigation system's problem mentioned above. The GNSS-based RF receiver model should have the structure to simultaneously receive both the conventional GPS and navigation information data of future-usable Galileo. As a result, it is constructed as the multi-band which can receive at the same time Ll band (1575.42MHz) of GPS and El band (1575.42MHz), E5A band (1207.1MHz), and E4B band (1176.45MHz) of Galileo This high precision localization architecture proposes a delay lock loop with the structure of Early_early code, Early_late code, Prompt code, Late_early code, and Late_late code other than Early code, Prompt code, and Late code which a previous delay lock loop structure has. As we suggest the delay lock loop structure of 1/4chips spacing, we successfully deal with the synchronization problem with the C/A code derived from inaccuracy of the signal received from the satellite navigation system. The synchronization problem with the C/A code causes an acquisition delay time problem of the vehicle navigation system and leads to performance reduction of the receiver. In addition, as this high sensitivity localization architecture is designed as an asymmetry structure using 20 correlators, maximizes reception amplification factor, and minimizes noise, it improves a reception rate. Satellite navigation system repeatedly transmits the same C/A code 20 times. Consequently, we propose a structure which can use all of the same C/A code. Since this has an adaptive structure and can limit(offer) the number of the correlator according to the nearby environment, it can reduce unnecessary delay time of the system. With the use of this structure, we can lower the acquisition delay time and guarantee the continuity of tracking.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.7
• /
• pp.1543-1551
• /
• 2011

Dithering scheme has been widely used to improve the resolution of DCO(Digitally Controlled Oscillator) in conventional ADPLLs(All Digital Phase Locked Loop). In this paper a new resolution improvement scheme is proposed where a simple DAC(Digital-to-Analog Converter) is employed to overcome the problems of dithering scheme. The frequencies are controled by varactors in coarse, fine, and DAC bank. The DAC bank consists of an inversion mode NMOS varactor. The other varactor banks consist of PMOS varactors. Each varactor bank is controlled by 8bit digital signal. The proposed DCO has been designed in a $0.13{\mu}m$ CMOS process. Measurement results shows that the designed DCO oscillates in 2.8GHz~3.5GHz and has a frequency tuning range of 660MHz and a resolution of 73Hz at 2.8GHz band. The designed DCO exhibits a phase noise of -119dBc/Hz at lMHz frequency offset. The DCO core consumes 4.2mA from l.2V supply. The chip area is $1.3mm{\times}1.3mm$ including pads.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.2
• /
• pp.171-179
• /
• 2017

In this paper, microstrip antenna using multi-layer and folded structure for GPS application is presented for aircraft loading. Existing microstrip patch antenna used dielectric of high specific inductive capacity to miniaturize that cause smaller bandwidth and decline of efficiency due to dielectric loss. To compensate the existing flaws, Rogers TMM 10i(dielectric constant=9.8, loss tangent=0.002) is used for multi-layer dielectric miniaturization, and we construct folded radiating element on the surface of the dielectric applying perturbation effect. The antenna is designed in the bandwidth of GPS $L_1$ band, and the size of the antenna's radiating element is $20.3mm{\times}19.93mm$, and it gets 94.2% miniaturized characteristic of basic ${\lambda}/2$ microstrip patch antenna. Also the measured -10 dB bandwidth is 32.3 MHz(2.05%), 3 dB axial ratio bandwidth is 6.7 MHz(0.43%). Measured radiation patterns was maximum gain of 0.56 dBi at x axis polarization, 1.23 dBi at y axis polarization.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.4
• /
• pp.409-412
• /
• 2002

The LNA(Low Noise Amplifier) is designed for use in low cost commercial application covered fully IMT-2000 band(1920~2170MHz, BW=250MHz). It is optimized source inductance for source lead and designed to equivalent etched line. The LNA uses a high pass impedance matching network for noise match and simple structure. The bias circuit designs have been made self-biased with a negative voltage applied to gate. The power supply voltage is 8V, total current is 180mA. The LNA is biased at a Vgs of -0.4, Vds of 4V for first stage and Vds of 5V for second stage. The LNA is designed competitively for commercial product specification. The measured gain and noise figure of the completed amplifier was 20dB and 1dB, respectively. Also, input VSWR, P1dB and gain flatness was measured of 1.14 ~ l.3dB, 22.4dBm and $\pm$0.45dB, respectively. The designed LNA can be used for commercial product.

• Journal of Advanced Navigation Technology
• /
• v.22 no.6
• /
• pp.616-622
• /
• 2018

Energy which is released by a huge earthquake can reach the ionosphere and induce disturbances. Those disturbances can detected by analyzing the global navigation satellite system (GNSS) satellite's signal. For detecting those disturbances, band-pass filter is generally used. Therefore, it is important to select proper pass band that can contain disturbance's frequency. In this paper, we analyzed a frequency of the ionospheric disturbances which are induced by earthquake by using GNSS signal. For analyzing seismogenic ionospheric disturbances, we calculated a geometry free combination of carrier phase to obtain a ionospheric delay. After that, the fast Fourier transform was applied to the 1 mHz high-passed ionospheric delay. As a result of analyzing disturbances, the frequency band of earlier disturbances was 4.5 mHz~11mHz and the representative frequency was 5.7 mHz. The frequency band of subsequent disturbances was 6 mHz~10 mHz and the representative frequency was 7.3 mHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.10
• /
• pp.1071-1078
• /
• 2003

In this paper, the planar, compact, and broadband phased array antenna system for IMT-2000 applications has been investigated. Two methods far designing a low-cost and low-complex beam-farming network are proposed. First, a new compact and broadband phase shifter with continuously controlled phase bits is designed by using parallel coupled lines. Second, its equivalent phase delay line is suggested to be capable of replacing the complex phase shifter with a reference phase bit on a phased array antenna. For the purpose of achieving the broadband system, in addition to the broadband phase shifter, a wide-slot antenna with a ground reflector is utilized as an element antenna. Therefore, the phased array antenna system has achieved compact size, broad bandwidth, and wide steering angle, although it has low complexity and low fabrication cost. The 3${\times}$1 phased array antenna system has a compact size of 1.6 λ${\times}$ l.6 λ, which is the sufficient ground plane of the wide-slot antenna. Experimental results present that the S$\_$11/ has less than 15 dB within the band and its radiation patterns on an E-plane have the capability of steering an antenna beam from -29$^{\circ}$to +30$^{\circ}$.