1년 전까지만 해도 조선시황은 한없는 호항을 누릴 것으로 보였다. 그러나 2008년 후반에 찾아든 글로벌 경제의 불황은 바로 해운시장을 뒤흔들었고 그 여파는 바로 조선 사장에도 한없는 추락을 가져오고 있다. 저자들은 이러한 사태를 예견하여 이미 드라이 도크의 건조에 신중을 기할 것을 주장한 바 있다. 여기에 비하여 Floating Dock는 건조 비용도 덜 들고, 건조 기간도 짧고, 이동성마저 갖추고 있기 때문에 훨씬 더 유연한 도크 건설 방법이 될 수 있다. 그러나 Floating Dock는 대형의 블록을 탑재할 때 갑작스런 중량의 이동으로 인한 중심의 큰 변화로 안정성이 크게 위협 받게 된다. 따라서 안전하게 블록을 탑재하기 위하여서는 아주 고도의 정밀한 발라스트 작업이 수행되어야 한다. 본 연구에서는 육상에서 만들어진 거대 블록을 플로팅도크에 밀어 넣는 Skid Launching System을 위한 플로팅도크 제어 시스템을 완성하여 안정적인 SLS를 구현하고자 한다. 이를 위하여 저자들은 우선 가상의 진수 절차를 만들어 모의 조정하는 시뮬레이터를 개발(Kim et al. 2008)한 바 있다. 본 논문에서는 이시뮬레이션을 바탕으로 실시간 모니터링하면서 실시간 제어하는 시스템을 만들고 실제 진수에 적용하고자 한다.
Journal of Advanced Marine Engineering and Technology
/
제39권10호
/
pp.1002-1010
/
2015
Natural gas hydrates are newly emerging as an environment-friendly source of energy to substitute for fossil fuels in the 21stcentury.NGHs are reported to holds much amounts of natural gas (up to 182 standard volumes of gas per volume of hydrate); they are easy to store and safe to carry at about minus 20 degree Celsius under atmospheric pressure because of the self-preservation phenomenon of gas hydrates. The transporting method by gas-ice-hydrate ship carriers has been introduced and developed by a variety of industry and research institutions. Our team has been conducted to develop NGH total systems, including a breakthrough NGH carrier for sea transportation, since 2011. The NGH pellet carrier does not require a separate cooling system for cargo, and the initial temperature is maintained through insulation of the cargo tanks throughout the transport to the final destination. The heat conducted from the exterior and passing through the insulation material of the hull should be cut off as much as possible, but heat inflow inside the cargo tank from an external source is inevitable during transport. In this study, the heat transfer in a cargo tank of a 115K NGH carrier was analyzed through simulation with a commercial CFD code to estimate the boil-off gas/boil-off rate on the developed carrier and understand major hazards that could significantly impact the safety of the vessel.
현재 조선 산업의 대형 블록제작 용접공정에서 용접용 캐리지(Carriage)를 이용한 반자동 용접 방법이 많이 사용되고 있다. 여기서의 캐리지는 수평 필렛 용접에서 용접 토치를 이송해 주는 장치이지만, 로봇 용접방법처럼 용접선을 추적하는 기능이 없어 곡선용접에는 사용이 불가능하며, 단순히 직선용접에만 사용할 수 있다. 또, 용접선을 추적하는 기능이 없기 때문에 직선용접에서도 용접오류가 자주 발생하여 이를 수정하는데 많은 시간과 비용이 소요되고 있다. 이에 본 논문에서는 현재 사용하고 있는 캐리지에 스트레인 게이지를 이용한 용접선 추적 센서와 80C196KC 마이크로컨트롤러를 추가 설치하여 직선 및 곡선용접에서 용접선을 자동으로 추적할 수 있는 시스템을 개발하여 사선 모형 및 컨테이너 박스 모형 용접선을 제작하여 추적현상에 대해 고찰하여 보았다.
Until now, many researches on laser-arc hybrid welding processes have been conducted mainly for high power CW laser and high direct current arc to weld the thick steel plates for shipbuilding. Recently, however the usage of thin steel plates, which tend to be deformed easily by thermal energy, is been increasing because of demand of light structure such as car body in the automobile industry. Accordingly, heat sources having relatively low heat input such as pulsed laser, dip-transfer DC GMA and pulsed GMA seem to be applied more increasingly and the study about those heat sources is needed more intensively. Any heat source mentioned above can not stand alone without weld defects at a relatively high welding speed for increasing the welding productivity. This is main reason to apply the hybrid welding process which uses pulsed laser and low-heat-input GMA heat sources simultaneously to weld the thin steel plate. In this study, parameters of pulsed laser and dip-transfer DC GMA welding are studied firstly through preliminary experiments, and then analyzed in the viewpoint of their physical phenomena. Before conducting the hybrid welding, a pulse control technique is developed based on the parallel port communication and Visual C++ 6.0. Owing to development of this technique, interactions of laser and arc pulses can be controlled consistently. Using the pulse control technique, the hybrid welding is conducted and then its interactive welding phenomenon is analyzed.
KSII Transactions on Internet and Information Systems (TIIS)
/
제12권5호
/
pp.2103-2123
/
2018
Ships built today are larger in scale and feature more complex structures. The ever-evolving systems used on board a ship require vast amounts of data processing. In the future, with the advent of smart ships, unmanned ships and other next-generation ships, the volumes of data to be processed will continue to increase. Yet, to date, ship data has been processed using wired networks. Placed at fixed locations, the nodes on wired networks often fail to process data from mobile devices. Despite many attempts made to use Wi-Fi on ships just as on land to create wireless networks, Wi-Fi has hardly been available due to the complex metal structures of ships. Therefore, Wi-Fi on ships has been patchy as the ship-wide total Wi-Fi coverage has not properly implemented. A new ship-wide wireless network environment is part of the technology conducive to the shipbuilding industry. The wireless network environment should not only serve the purpose of communication but also be able to manage and control multiple features in real-time: fault diagnostics, tracking, accident prevention and safety management. To better understand the characteristics of wireless frequencies for ships, this paper tests the widely used TETRA, UHF and Wi-Fi and sheds light on the features, advantages and disadvantages of each technology in ship settings. The proposed deployment of a Super Wi-Fi network leveraging the legacy UHF system of TMS generates a ship-wide wireless network environment. The experimental findings corroborate the feasibility of the proposed ship-wide Super Wi-Fi network environment.
To investigate the actual distribution condition and clothing construction factors of the working clothes supplied to the Changwon national industrial complex, 5 major companies in machinery, automotive, industrial engineering, shipbuilding and rolling stock in the industrial complex located in Gyeongsangnam-Do were selected. The questionnaire designed for the research consisted of working clothes distribution policies in manufacturing industry and the actual conditions of the design facts, repair and maintenance of the working clothes, etc. The analysis of the clothing construction factors of the working clothes provided by 5 respondent companies were conducted in parallel. The results derived from the study were as follows: The basic types of working clothes were the blouson jacket and straight pants; safety equipments for manufacture were safety helmets, gloves, snickers, goggles, masks, ear caps, wristlets, leggings, apron, etc. The size-charts adopted by the participant companies were the small-medium-large and cm/inch measurement size systems. To solve wearer's dissatisfaction with the garment fit, certain clothing construction factors were used, e.g. strap bands and the elastic band on a waist band. The types of fabrics used for the working clothes were mainly polyester/cotton and polyester/rayon blended ones. Moreover, to provide with more air permeability to wearers, the warp knit material was used to construct the lining and the armpit or back bodice slits. Lock, two-thread chain, safety, overedge stitches were applied with flat, lap felled, French, superimposed, lapped, bound and edge finishing seams to construct the working clothes selected.
Application of newly conceptualized Anti-Splash Devices designed for COT vent pipes were studied on a P/V valve located on the upper deck of an oil carrier vessel. Anti-Splash devices are used in the shipbuilding industry in order to avoid oil overflow and spray accidents caused by excess pressure and vacuum condition in the cargo oil tanks. These conditions are caused by the transverse and longitudinal sloshing forces that arise from ship motion during sea voyages. The main issue with existing Anti-Splash device model is flux at the outlet of the Anti-Splash Device, and so, new conceptual models for the Anti-Splash device were developed and compared to existing Anti-Splash device model using CFD analysis. Transient analysis was used to capture the flow and velocity of each model and a comparative analysis was performed between old and new-concept models. This data was used to determine the optimal design parameters in order to develop an optimized Anti-Splash Device. A Factory acceptance test was performed on the new-concept models in order to verify the performance and efficiency against their design requirements and other criterion. The final step performed was to apply the optimized Anti-Splash Device models for COT vent pipes to an actual vessel and verify performance through a seawater cargo operation during a sea voyage as per the ship owner's request. The patent for the aforementioned device was obtained by the Korean Intellectual property Office dated Dec. 18th,2014.
최근 국내 조선 산업과 IT융합기술에 대한 연구가 활발한 가운데 선박 안전운항을 위한 위성탐지 기술 발달로 선박에서는 장거리 식별추적 장치 및 자동식별 장치의 의무화로 선박이동 상황을 모니터링 할 수 있어 안전항해에 도움을 주고 있으나, 무중항해 시 시정 상태를 레이다에 의존하는 항해사에게 위험을 경보해 줄 수 있는 안전장치 개발이 필요하다. 이에 광센서를 이용하여 감지하고 알려주는 해무 감지 경보 시스템을 개발하였다. 제작된 해무 감지 경보 시스템은 소형, 저 전력의 광센서 송수신기와 센싱 데이터 처리 모듈로 구성되었다. 시험을 통해 해무가 있는 경우와 없는 경우 각각에 대해 제작된 해무 경보 시스템은 해무 농도를 검출하는 것을 확인하였다. 또한 해무 농도에 따라 선박 엔진 RPM 조절이 가능하고, 결과적으로 선박의 안전 운항을 보조 장치로 활용 가능함을 확인하였다.
전 세계적으로 기후변화의 패러다임에 따라 조선업계에서도 친환경연료를 이용하는 추진시스템이 고려되면서, 다양한 추진기 역시 각광을 받고 있다. 일반적인 프로펠러와 타로 구성되었던 추진기들은 전방위추진기(아지무스 스러스터)라는 특수한 추진기의 발전으로부터 그 종류가 다양해지고 있다. 이러한 전방위추진기는 과거에는 예인선에 많이 설치되어 있으나, 현재는 동적위치제어시스템을 탑재한 해양플랜트운영선박에 많이 설치되어 사용되고 있는데, 이는 일반적인 추진기의 조타 방법과 상이하여 승선하는 선원들이 그 특성을 익히는데 많은 시간이 소요되고 있다. 아울러 이러한 특수한 추진기와 관련한 교육 역시 제한적으로 존재한다. 본 연구에서는 전방위추진기 탑재 선박의 조종 미숙으로 발생한 해양사고를 STAMP 기법을 통해 원인을 분석한 후 특수한 추진기를 설치한 선박의 안전 운항을 위해 표준조타명령에 대한 필요성을 시사하고자 한다.
조선 및 해운·물류 분야의 디지털 전환은 자율운항선박의 도입 및 선박의 운항방식의 변화를 이끌 것으로 예상된다. 기존 운항방식과 함께 자율운항, 원격운항 등 다양한 운항형태가 공존하며, 선박 운용 프로세스의 전환과 새로운 이해관계자의 등장이 전망된다. 본 논문에서는 선박 운항방식 변화에 따른 미래 선박 운항 프로세스를 분석하고, 미래 선박의 운항환경 변화를 예측하여 주요 업무별·이해관계자별 기능요건을 도출하고자 한다. 델파이 기법을 활용하여 항해 및 화물운송 계획 수립단계부터 최종 목적항 입항 및 화물 하역단계까지 선박 운항 시나리오를 구성하고, 업무별, 수행 주체별 미래 업무 변화를 예측했다. 원격운항, 자율운항 등으로 선원의 개입이 최소화될 것이며, 각 분야의 전문가가 선박 운항의 다양한 측면에서 책임과 의무를 갖게 될 것으로 예상된다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.