• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.10
• /
• pp.1413-1421
• /
• 1993

It is possible to weaken the undesirable effect of a bounded control input signal to the plant and done by setting up an additional correction loop which compensates for the suppresed portion of the control input signal. The design and analysys of stability of state controller is used by the Kalman-Szego-Lemma and as the result of this method is made possible to take advantage of the control input to the plant even for small error signals.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.5
• /
• pp.1240-1255
• /
• 1996

This paper suggests power optimization technique in multi-level SCPC system as a method for efficient utilization of limited satellite power. The power optimization is realized by optimal assignment of satellite input carrier powers considering interference and noise generated in up-link and down-link. The Fletcher-Powell algorithm searching minimum(or maximum) point using gradient information is used to detemine the optimal input carrier powers. To apply Flectcher-Powell algorithm mathematical descriptions and their partial derivatives to interference and nose are presented. Because a target, which should be optimized, is satellite input carrier power, amplitude of each carrier group will be assumed to be an independent variable. The performance criterion for optimal power assignmentis classified into 4 categories with respect to CNR of destination receiver earth station to meet the requirement for various satellite link environment. Simulation results for two-level, four-level and six-level SCPC system are presented.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.10
• /
• pp.697-702
• /
• 2004

In this paper, we proposed that the problem of controlling induction motor with magnetic saturation, is studied from an input-output feedback linearization with adaptive algorithm. is considered. An adaptive input-output feedback linearizing controller is considered under the assumption of known motor parameters and unknown load torque. In order to achieve the speed regulation with the consideration of improving power efficiency, rotor angular speed and flux amplitude tracking objectives are formulated. Simulation results are provided for illustration.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2006.05a
• /
• pp.1707-1714
• /
• 2006

In order to enhance sustainable war fighting capabilities, it is important to maintain a good ammunition support system. In this paper, we evaluate the performance of Ammunition companies using Imprecise Data Envelopment Analysis (IDEA)-BCC and IDEA-Additive model, which can deal with imprecise data in DEA. In order to select a list of input and output variables, we used a multiple regression analysis. We could choose input variables that have significant effects on the output performance with stepwise regression model. From the regression analysis, the number of soldiers, officers, and ammunition warehouses were selected as the input variables. Seven out of sixteen Ammunition companies were found to be inefficient by the IDEA-BCC model. And using IDEA-Additive model, we could identify the input excess and the output shortfall in reaching at a point on the efficiency frontier.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.30-34
• /
• 1997

This paper Describe a modelling method for SCR(selective Catalytic reduction) system in refuse incineration plant. We consider the SCR system as a single input single output system. For modelling the SCR system, an auto regressive exogeneous(ARX) modelling method is used. In this case, we should design the white noise input for modelling and put it on the system as an input (.NH/sap2/.), and taken an outlet NOx as an output. From these two relations, we design the ARX model with 45 second delay time and transform to discrete system with 0.5 sampling time. Using the obtained SCR model, we simulate the SCR system to reduce the outlet NOx content by a conventional PID control method.

• Journal of the Korean Ceramic Society
• /
• v.27 no.2
• /
• pp.219-225
• /
• 1990

Silicon dioxide thin film has been grown by a chemical vapor deposition (CVD) technique using SiH4, and O2 gaseous mixture on a silicon substrate. The experimental results indicated that the deposition rate as a function of the input ratio (O2/SiH4) shows two regions, increasing region and decreasing region. Also the deposition rate increases with increasing the deposition temperature. The microstructure of deposited silicon dioxide films is amorphous. The experimental results of infrared absorption spectrums indicate that Si-H and Si-OH bond increase with decreasing input ratio, but Si-O bond is independent on the input ratio. The interfacial charge of deposited silicon dioxide decreases with increasing input ratio.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.2
• /
• pp.229-234
• /
• 2008

An AC-DC transfer standard(TS) is used for the AC voltage standard in the range of 2 mV to 1000 V below 1 MHz. Micro-potentiometer(${\mu}Pot$) is used to evaluate the ac-dc transfer difference(ADD) of the TS below 200 mV range. The ADD of the TS were changed by the loading effect caused from the input impedance change of the TS depend on frequency. An input impedance evaluation technique of the TS using ${\mu}Pot$ has been developed.

• Journal of the Korean Society of Safety
• /
• v.15 no.2
• /
• pp.92-96
• /
• 2000

In this experiment, we studied about concentration characteristics of $NO_x$ and generation of ozone in the reactor of corona discharge type by using mixed gas of $NO/N_2$ and $N_2/O_2$. In the case of the initial NO concentration increased, decrease rate of NO concentration was weakened and discharge input power of minimum NO concentration became high. When NO concentration was high, NO decomposition limit was appeared. And NO reduction rate was decreased, when initial NO concentration and discharge input power increased. When discharge input power was 5W, we could know the most proper energy value for treatment of NO. When the concentration of initial NO increased, generation of ozone decreased and in the case of same concentration of NO, according to discharge input power increase, generation of ozone increased.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.11a
• /
• pp.107-111
• /
• 2001

This paper presents a detailed analysis method of the universal input forward converter with LC input filter operating in discontinuous capacitor voltage mode(DCVM) for wind power generation. In this analysis, condition for DCVM operation and conversion ratio for rectified sinusoidal input are made clear. To verify the validity of the analysis, simulation is carried out for the universal input ranging from 90 $V_{rms} to 260 V_{rms}$

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.585-590
• /
• 2000

Recently, It is gradually raised necessity that thickness of thin film is measured accuracy and managed in industrial circles and medical world. Ultrasonic Signal processing method is likely to become a very powerful method for NDE method of detection of microdefects and thickness measurement of thin film below the limit of Ultrasonic distance resolution in the opaque materials, provides useful information that cannot be obtained by a conventional measuring system. In the present research, considering a thin film below the limit of ultrasonic distance resolution sandwiched between three substances as acoustical analysis model, demonstrated the usefulness of ultrasonic Signal processing technique using information of ultrasonic frequency for NDE of measurements of thin film thickness, sound velocity, and step height, regardless of interference phenomenon. Numeral information was deduced and quantified effective information from the image. Also, pattern recognition of a defected input image was performed by neural network algorithm. Input pattern of various numeral was composed combinationally, and then, it was studied by neural network. Furthermore, possibility of pattern recognition was confirmed on artifical defected input data formed by simulation. Finally, application on unknown input pattern was also examined.