• 한국안광학회지
• /
• 제9권1호
• /
• pp.29-34
• /
• 2004

본 연구는 타각적 검사장비의 개발을 위한 연구로 PC를 기반으로 Foucault Test (Knife edge Test)를 이용하여 굴절상태의 측정을 목표로 하였다. Knife edge Test를 이용하여 입사광선이 망막에서 반사된 출사광선의 이미지를 CCD 카메라를 사용하여 촬영하고, 그 이미지를 분석하여 반사상의 지름을 측정하여 동공의 크기를 측정하였다. 또한 반사 이미지의 방향으로 굴절상태를 판정하고 반사 이미지의 높이를 측정하여 굴절이상도를 확인하였다. 구면수차는 반사상과 반대방향에 나타나는 부반사 이미지의 명도를 비교하여 측정하였고, 그 크기를 통해 수차값을 계산할 수 있었다.

• 한국의학물리학회지:의학물리
• /
• 제29권2호
• /
• pp.73-80
• /
• 2018

Accelerated partial breast irradiation (APBI) is a new treatment delivery technique that decreases overall treatment time by using higher fractional doses than conventional fractionation. Here, a quantitative analysis study of CyberKnife-based APBI was performed on 10 patients with left-sided breast cancer who had already finished conventional treatment at the Inha University Hospital. Dosimetric parameters for four kinds of treatment plans (3D-CRT, IMRT, VMAT, and CyberKnife) were analyzed and compared with constraints in the NSABP B39/RTOG 0413 protocol and a published CyberKnife-based APBI study. For the 10 patients recruited in this study, all the dosimetric parameters, including target coverage and doses to normal structures, met the NSABP B39/RTOG 0413 protocol. Compared with other treatment plans, a more conformal dose to the target and better dose sparing of critical structures were observed in CyberKnife plans. Accelerated partial breast irradiation via CyberKnife is a suitable treatment delivery technique for partial breast irradiation and offers improvements over external beam APBI techniques.

• Corrosion Science and Technology
• /
• 제23권3호
• /
• pp.228-234
• /
• 2024

Zinc wiping is a phenomenon used to control zinc-coating thickness on steel substrate during hot dip galvanizing by equipment called air knife. Uniformity of zinc coating weight in length and width profile along with surface quality are most critical quality parameters of galvanized steel. Deviation from tolerance level of coating thickness causes issues like overcoating (excess consumption of costly zinc) or undercoating leading to rejections due to non-compliance of customer requirement. Main contributor of deviation from target coating weight is dynamic change in air knives equipment setup when thickness, width, and type of substrate changes. Additionally, cold coating measurement gauge measure coating weight after solidification but are installed down the line from air knife resulting in delayed feedback. This study presents a coating weight control model (Galvantage) predicting critical air knife parameters air pressure, knife distance from strip and line speed for coating control. A reverse engineering approach is adopted to design a predictive, prescriptive, and descriptive model recommending air knife setups that estimate air knife distance and expected coating weight in real time. Implementation of this model eliminates feedback lag experienced due to location of coating gauge and achieving setup without trial-error by operator.

• Journal of Korean Neurosurgical Society
• /
• 제30권sup2호
• /
• pp.289-293
• /
• 2001

Objectives : The optimal treatment of craniopharyngioma is controversial. Despite recent advances in microsurgical management, complete surgical removal of craniopharyngioma remains very difficult. Radiation added to surgery is effective, but radiation therapy resulted in untoward side effect in young patient. Gamma knife radiosurgery offers the theoretical advantage of a reduced radiation dose to surrounding structures during the treatment of residual or recurrent craniopharyngioma compared with fractionated radiotheraphy. We described retrospective analysis of tumor size and clinical symptoms of patients after gamma knife radiosurgery in residual or recurrent craniopharyngioma were performed. Material and Methods : From September 1990 to January 2000, 18 patients of craniopharyngioma were treated by gamma knife radiosurgery. All patient had undergone surgery, but residual or recurrent tumor was found and all of them treated postoperative gamma knife radiosurgery. The mean age was 19(from 6 to 66) and male to female ratio was 10 to 8 and 8 patients were below 15 years old. In young age group(below age 15), the average volume of the tumor was $2904.8mm^3$ and mean maximal gamma knife dose was 34.9Gy. In old age group(older than 15), the average volume of the tumor was $2590.4mm^3$ and mean maximal gamma knife dose was 45.2Gy. The size of the tumor was average $2730.1mm^3$($88-12000mm^3$), mean average radiation dose was 40.7Gy and the mean prescription dose was 17.6 Gy(4-35Gy) delivered to a median prescription 50.7% isodose. Results : The follow up was from 1 year to 9 years(mean 59.1 months) after gamma knife radiosurgery. The tumor was controlled in 13(72.2%) patients. The tumor decreased in 9 patients and not changed in 4 patients. The tumor size increased in 4(22.2%) patients during follow up period. In two cases the tumor size increased because of its cystic portion was increased, but their solid portion of the tumor was not changed. In another two patients, the solid portion of the tumor was increased. So, one patient underwent reoperation and the other patient underwent operation and repeated gamma knife radiosurgery. The tumor recurred in one case(5.6%) that is a outside of irradiated site. The presenting symptoms were improved in 4 patients(improved visual acuity in 1, controlled increased intracranial presure sign in 3 patients). In one case, visual acuity decreased after gamma knife radiosurgery. The endocrine symptoms were not influenced by gamma knife radiosurgery. Conclusion : Craniopharyngioma can be treated successfully by gamma knife radiosurgery. Causes of the tumor regrowth are inadequate dose planning because of postoperatively poor margination of the tumor, close approximation of optic nerve and residual tumors outside the target lesion. Recurrence can develop 4 years after gamma knife radiosurgery. Volume is important, but the accurate targeting is more important to prevent tumor recurrence. If the tumor definition is not clear during planning gamma knife surgery, long-term image follow up is required.

• 한국의학물리학회지:의학물리
• /
• 제14권3호
• /
• pp.184-188
• /
• 2003

감마나이프는 일회에 대용량의 방사선량을 조사하여 뇌정위 방사선 수술을 하기 때문에, 주기적인 정도 관리가 매우 중요하다. 그러나 국내의 경우 학회 및 규제기관 차원에서 권고되고 있는 표준화된 정도관리 절차서가 없이, 각 기관별로 독자적인 정도관리 절차서를 개발하여 시행되고 있어, 기관별로 상호 비교하기가 어려운 실정이다. 따라서 본 연구에서는 국내 실정에 적합한 감마나이프 정도관리 프로그램을 개발하기 위해, 제조사, 미국 및 일본에서 권고하고 있는 정도관리 절차서를 수집하여 비교 분석하였다 또한 감마나이프에 대한 주기적인 정도관리 검사항목을 선량관련 검사항목, 기계적인 검사항목 및 안전 관리적인 측면으로 분류하였다. 미국의 경우 제조사 보다 엄격하게 권고 및 규제하고 있으며, 일본의 경우 미국의 절차서를 토대로 검사항목 및 주기를 권고하고 있다. 이를 토대로 국내 실정에 적합한 감마나이프 정도관리 절차를 제시하고자 한다.

• Journal of Korean Neurosurgical Society
• /
• 제43권1호
• /
• pp.26-30
• /
• 2008

Objective : The authors developed a stereotactic device for irradiation of small animals with Leksell Gamma Knife Model C. Development and verification procedures were described in this article. Methods : The device was designed to satisfy three requirements. The mechanical accuracy in positioning was to be managed within 0.5 mm. The strength of the device and structure were to be compromised to provide enough strength to hold a small animal during irradiation and to interfere the gamma ray beam as little as possible. The device was to be used in combination with the Leksell G-$frame^{(R)}$ and $KOPF^{(R)}$ rat adaptor. The irradiation point was determined by separate imaging sequences such as plain X-ray images. Results : The absolute dose rate with the device in a Leksell Gamma Knife was 3.7% less than the value calculated from Leksell Gamma $Plan^{(R)}$. The dose distributions measured with $GAFCHROMIC^{(R)}$ MD-55 film corresponded to those of Leksell Gamma $Plan^{(R)}$ within acceptable range. The device was used in a series of rat experiments with a 4 mm helmet of Leksell Gamma Knife. Conclusion : A stereotactic device for irradiation of small animals with Leksell Gamma Knife Model C has been developed so that it fulfilled above requirements. Absorbed dose and dose distribution at the center of a Gamma Knife helmet are in acceptable ranges. The device provides enough accuracy for stereotactic irradiation with acceptable practicality.

• Journal of Korean Neurosurgical Society
• /
• 제37권1호
• /
• pp.48-53
• /
• 2005

Objective: The purpose of this study is to elucidate in vitro responses to combined gamma knife irradiation and p53 gene transfection on human malignant glioma cell lines. Methods: Two malignant human glioma cell lines, U87MG (p53-wild type) and U373MG (p53-mutant) were transfected with an adenoviral vector containing p53 (MOI of 50) before and after applying 20Gy of gamma irradiation. Various assessments were performed, including, cell viability by MTT assay; apoptosis by annexin assay; and cell cycle by flow cytometry, for the seven groups: mock, p53 only, gamma knife (GK) only, GK after LacZ, LacZ after GK, GK after p53, p53 after GK. Results: Cell survival decreased especially, in the subgroup transfected with p53 after gamma irradiation. Apoptosis tended to increase in p53 transfected U373 MG after gamma irradiation (apoptotic rate, 38.9%). The G2-M phase cell cycle arrest markedly increased by transfecting with p53, 48 hours after gamma knife irradiation in U373 MG (G2-M phase, 90.8%). Conclusion: These results suggest that the in vitro effects of combined gamma knife irradiation and p53 gene transfection is an augmentation of apoptosis and G2-M phase cell cycle arrest, which are more exaggerated in U373 MG with p53 transfection after gamma knife irradiation.

• Journal of Korean Neurosurgical Society
• /
• 제29권3호
• /
• pp.336-344
• /
• 2000

Objective : The treatment for prolactin secreting pituitary adenoma(prolactinoma) include pharmacology, surgery, radiation therapy or radiosurgery. The recent development of radiological imaging and microsurgery has made transsphenoidal microsurgery the treatment of choice for most prolactin secreting pituitary adenoma. Despite its low morbidity and mortality, relatively high recurrence and failure rate have been reported. Recent advances in neuroimaging provide a precise targeting in radiosurgery for treatment of prolactin secreting pituitary adenoma. In this regard, Gamma knife radiosurgery has been proposed as an alternative primary treatment modality or adjuvant therapy. Patients and Methods : Twenty three patients with prolactin secreting pituitary adenoma have been treated with Gamma knife radiosurgery in our institute from March 1992 to September 1998. We analyzed clinical, radiological and endocrinological changes in 21 patients who were followed up for an average of 35.7 months. Results : The mean age was 34.9 years and 16 patients were treated with Gamma knife radiosurgery as primary treatment and 5 patients underwent Gamma knife radiosurgery for residual tumors after microsurgery. The margin of the tumor was incorporated within the 40 to 80% and the mean marginal dose was 24.5 Gy. Clinical improvement in the last follow-up were present in 17 cases(81.0%) and 3 of 5 infertility patients became pregnant after Gamma knife radiosurgery. Tumor control rate after Gamma knife radiosurgery was 100%. Endocrinological normalization in the last follow-up were obtained in 12 cases(57.1%). In three cases, hormonal normalizations were present in early period(3-32 months) but serum hormone levels were elevated subsequently. Conclusion : We conclude that the Gamma knife radiosurgery for prolactin secreting pituitary adenoma seems to be safe and effective as adjuvant therapy after microsurgery and primary treatment modality in selective patients.

• Corrosion Science and Technology
• /
• 제9권3호
• /
• pp.105-108
• /
• 2010

The product specification of the Continuous Hot Dip Galvanizing Line (CGL) changes and varies constantly with different customers' requirements, especially in the zinc coating weight which is from 30 to 150 g/$m^2$ on each side. Since the coating weight of zinc changes often, it is very important to reduce time spent in the transfer of target values changed for low production cost and yield loss. The No.2 CGL in China Steel Corporation (CSC) has improved the control of the air knife which is designed by Siemens VAI. CSC proposed an experiment design which is an $L_9(3^4)$ orthogonal array to find the relations between zinc coating weight and the process parameters, such as the line speed, air pressure, gap of air knife and air knife position. A non-linear regression formula was derived from the experimental results and applied in the mathematical model. A new air knife feedforward control system, which is coupled with the regression formula, the air knife control system and the process computer, is implemented into the line. The practical plant operation results have been presented to show the transfer time is obviously shortened while zinc coating weight target changing and the product rejected ratio caused by zinc coating weight out of specification is significantly reduced from 0.5% to 0.15 %.

• 한국안전학회지
• /
• 제23권4호
• /
• pp.67-71
• /
• 2008

Formwork is a temporary structure that supports its weight and that of fresh concrete as well as construction live loads. Slab formwork consists of sheathing, stringer, hanger and shore. In construction site, pipe supports are usually used as shores which are consisted of the slab formwork. In this study, compressive strength of 80 pipe supports was measured by knife edge test and plate test. Buckling load of pipe supports was analyzed by structural analysis program(MlDAS). Theoretical buckling load with/without initial deformation was got by theoretical analysis. According to these results, buckling load which was analyzed by structural analysis program(MlDAS) was larger than compressive strength of knife edge test and plate test. Theoretical buckling load without initial deformation was larger than compressive strength of knife edge test and plate test. But Theoretical buckling load with initial deformation was lower than compressive strength of knife edge test and plate test. Initial deformation equation for test method according to the pipe support length was suggested. Therefore, the present study results will be used to design the slab formwork safely.