• Journal of the Korean Chemical Society
• /
• v.17 no.2
• /
• pp.73-79
• /
• 1973

The ultrasonic absorption of Dodecyl pyridinium bromide (D.P.B.) in aqueous solution has been measured at $20^{\circ}C$ over a range of frequencies between 0.1 mc and 90 mc and a range of concentrations from 5 to 100 mM. The excess absorption was observed only in the solutions the concentration of which was higher than the critical micellar concentration (c.m.c.) both in the presence and absence of salt. The excess absorption of sound and the relaxation frequencies obtained from the absorption curves show a discontinuity with the variation of the concentration of D.P.B. in the neighborhood of 60 mM. Other properties such as viscosity, conductivity and velocity of sound also exhibit such a change near the same concentration. It is concluded that a change in the properties of the micelles of D.P.B. occurs in the neighborhood of this concentration. The mechanism of the observed ultrasonic excess absorption in attributed to the reaction $M_2{\rightleftarrow}M_1+2Br^-$where$M_2$ and$M_1$are two types of micelles. The rate constants of forward and backward reactions are found to be $6.9 {\times} 10^5 sec^{-1)$and $6.7{\times}10^{10}sec^{-1}mole{-2}$ respectively. Some kinetic characteristics including free energy, enthalpy, entropy and activation energy were calculated.

• Korean Journal of Applied Biomechanics
• /
• v.31 no.4
• /
• pp.276-282
• /
• 2021

Objective: To investigate effects of Fibular Repositioning Taping (FRT) on lower extremity joint stiffness and angle during drop-landing. Method: Twenty-eight participants (14 healthy, 14 with chronic ankle instability [CAI]) performed drop-landings from a 60 cm box; three were performed prior to tape application and three were performed post-FRT. Three-dimensional kinematic and kinetic data were collected using an infrared optical camera system (Vicon Motion Systems Ltd. Oxford, UK) and force-plate (AMTI, Watertown, MA). Joint stiffness and sagittal angle of the ankle, knee, and hip were analyzed. Results: The hip [Healthy: p<.05; M ± SD: 29.43 ± 11.27 (pre), 33.04 ± 12.03 (post); CAI: p<.05; M ± SD: 31.45 ± 9.70 (pre), 32.29 ± 9.85 (post)] and knee [Healthy: p<.05; M ± SD: 53.44 ± 8.09 (pre), 55.13 ± 8.36 (post); CAI: p<.05; M ± SD: 53.12 ± 8.35 (pre), 55.55 ± 9.81 (post)] joints demonstrated significant increases in sagittal angle after FRT. A significant decrease in joint angle was found at the ankle [Healthy: p<.05; M ± SD: 56.10 ± 3.71 (pre), 54.09 ± 4.31 (post); CAI: p<.05; M ± SD: 52.80 ± 6.04 (pre), 49.86 ± 10.08 (post)]. A significant decrease in hip [Healthy: p<.05; M ± SD: 1549.16 ± 517.53 (pre), 1272.48 ± 646.73 (post); CAI: p<.05; M ± SD: 1300.42 ± 595.55 (pre), 1158.27 ± 550.58 (post)] and knee [Healthy: p<.05; M ± SD: 270.12 ± 54.07 (pre), 239.13 ± 64.70 (post); CAI: p<.05; M ± SD: 241.58 ± 93.48 (pre), 214.63 ± 101.00 (post)] joint stiffness was found post-FRT application, while no difference was found at the ankle [Healthy: p>.05; M ± SD: 57.29 ± 17.04 (pre), 59.37 ± 18.30 (post); CAI: p>.05; M ± SD: 69.15 ± 17.63 (pre), 77.24 ± 35.05 (post)]. Conclusion FRT application decreased joint angle at the ankle without altering ankle joint stiffness. In contrast, decreased joint stiffness and increased joint angle was found at the hip and knee following FRT. Thus, participants utilize an altered shock absorption mechanism during drop-landings following FRT. When compared to previous research, the joint kinematics and stiffness of the lower extremity appear to be different following FRT versus traditional ankle taping.

• Journal of Convergence for Information Technology
• /
• v.11 no.9
• /
• pp.109-114
• /
• 2021

Cr(VI)-quinoline compound[(C₉H₇NH)₂Cr₂O₇] was synthesized by the reaction between of quinoline and chromium(VI) trioxide, and structure was FT-IR, elemental analysis. The oxidation ability of benzyl alcohol greatly depends upon the dielectric constant of the used organic solvent, where carbon tetrachloride was worst and N,N'-dimethylformamide was best solvent. Noticeably, in N,N'-dimethylformamide solvent, Cr(VI)-quinoline compound oxidized substituted benzyl alcohols. The Hammett reaction constant(ρ)=-0.69(303K). As a resuit, Cr(VI)-quinoline compound was found as efficicent oxidizing agent that converted benzyl alcohol, allyl alcohol, primary alcohol and secondary alcohols to the corresponding aldehydes or ketones. Cr(VI)-quinoline compound was selective oxidizing agent of benzyl alcohol, allyl alcohol and primary alcohol in the presence of secondary alcohol ones.

• Journal of Korean Medical Ki-Gong Academy
• /
• v.20 no.1
• /
• pp.118-147
• /
• 2020

Objective : The purpose of this study is to understand trends of pelvic correction therapy in Korea and to assist research activities on pelvic correction therapy. Also, this study selected and presented indicators for measuring pelvic slope to help ensure consistent studies with uniform indicators in future studies related to pelvic correction. Methods : The following keywords "골반", "골반 교정", "골반 변위" "Pelvic correction" were searched on three specialized search sites (RISS, NAI, DBpia). Trends in pelvic correction therapy were analyzed through the selected researches suitable among these searched researches in an overview format. Results : 1. A total of 7,806 studies were searched and a total of 268 studies were finally selected. 2. Studies began in 1977 and have been actively studied until recently, with 35 studies in 2017 being the most recent trend since 2000. 3. In the results according to the Main Field of Research, the 'Arts and Kinesiology'(113, 42.16%) and 'Medicine and Pharmacy'(103, 38.43%) were the most in order. To the Middle Field, the 'Kinesiology was the largest with 96(35.82%) studies. 4. In the results according to the study design, 'Pre-Post Test(PPT)' was the largest with 107 studies. 5. In the results according to the Intervention, 'Exercise' was the largest with 165 studies, of which 'Pilates' and 'Yoga' in 'Training' was the largest. 6. Among the evaluation method, the 'Pelvic Index' was used 146 times, followed by 'Spinal Alignment (99)', 'Other Joints (93)', and 'Kinetic Specialized Measurement Test (56)'. 7. Among the evaluation methods, the pelvic slope measurement indicators were PT (58), PH (48), Pelvic Torsion (40), Iliac Crest (38), ASIS-PSIS distance/angle (27), and Pelvic Width (I.W., I.L., S.W) (25) in order. 8. The journals that published the most researches were KJSS(Korean Alliance For Health, Physical Education, Recreation, And Dance;9), and JKPT(Korean Physical Therapy;9). Among the University, the Graduate School of Silla University published the most papers (12). 9. The author who published the most studies were Seungjin Park(3), the co-authors were Hoseong Lee, Gideok Park, Seongsu Bae(3), and the Thesis-Director Gyeongok Lee(7). Conclusions : 1. Studies on pelvic correction treatment continue to increase every year. 2. The main academic field of pelvic correction is 'Sports', 'Physical Therapy', and 'Medical Science'. 3. The most chosen research design method in the study on pelvic correction treatment was 'Pre-Post Test(PPT)', primarily as an intermediary, Pilates and yoga during exercise therapy, and then Chiropractic during handcraft were used as multiple frequencies. 4. Among the various measurement method indicators of pelvic correction previously used, multiple frequency was taken up in the order of PT, PH, Pelvic Torsion, iliac crest, ASIS-PSIS distance/angle, and pelvic width (I.W.,I.L.,S.W). Typically, measurements through "ASIS-PSIS angle" are recommended and are considered as the most rational in clinical trials.

• Korean Journal of Applied Biomechanics
• /
• v.33 no.3
• /
• pp.110-117
• /
• 2023

Objective: The purpose of this study was to find out kinematic and kinetic differences the lower extremity joint according to the landing type during vertical jump movement after jump landing, and to present an efficient landing method to reduce the incidence of injury in youth players. Method: Total of 24 Youth players under Korean Sport and Olympic Committee, who used either heel contact landing (HCG) or toe contact landing (TCG) participated in this study (HCG (12): CG height: 168.7 ± 9.7 cm, weight: 60.9 ± 11.6 kg, age: 14.1 ± 0.9 yrs., career: 4.3 ± 2.9 yrs., TCG height: 174.8 ± 4.9 cm, weight: 66.9 ± 9.9 kg, age 13.9 ± 0.8 yrs., career: 4.7 ± 2.0 yrs.). Participants were asked to perform jump landing consecutively followed by vertical jump. A 3-dimensional motion analysis with 19 infrared cameras and 2 force plates was performed in this study. To find out the significance between two landing styles independent t-test was performed and significance level was set at .05. Results: HCG showed a significantly higher dorsi flexion, extension and flexion angle at ankle, knee and hip joints, respectively compared with those of TCG (p<.05). Also, HCG revealed reduced RoM at ankle joint while it showed increased RoM at knee joint compared to TCG (p<.05). In addition, HGC showed greater peak force, a loading rate, and impulse than those of TCG (p<.05). Finally, greater planta flexion moment was revealed in TCG compared to HCG at ankle joint. For the knee joint HCG showed extension and flexion moment in E1 and E2, respectively, while TCG showed opposite results. Conclusion: Compared to toe contact landing, the heel contact landing is not expected to have an advantage in terms of absorbing and dispersing the impact of contact with the ground to the joint. If these movements continuously used, performance may deteriorate, including injuries, so it is believed that education on safe landing methods is needed for young athletes whose musculoskeletal growth is not fully mature.

• Korean Journal of Applied Biomechanics
• /
• v.12 no.2
• /
• pp.279-293
• /
• 2002

In the study the subjects who 10 university golfers act, and the kinetic factors were analyzed by the ground reaction system. the conclusion are as follows. 1) In the golf putting swing, the ground reaction factors of sagital plane in aspect are showen that the left and right foot sufficient difference, in the level of p <.05. 2) In the golf putting swing, the ground reaction factors of frontal plane in aspect is showen that the left foot has no significant difference in AD BS in the level of p < .05. In success, IP, FS. It can show significant difference. In addition, the right foot is shown the success, There is significant difference. 3) In the golf putting swing, the ground reaction factors of the vertical plane in aspect are shown that the left foot has no significant difference in BS, FS in the level p < .05. In success, AD, IP. It can show significant difference. In addition, the right foot is shown the success, There is significant difference. 4) In the golf putting swing, the ground reaction factors of torque in aspect are shown that the left foot had no significant difference in BS in the level p < .05. In success, AD, IP, FS. It can show significant difference. In addition, the right foot has no significant difference in IP in the level p < .05. AD, BS, FS. There is significant difference. The summarized conclusions are as follows. The first that the power of sagital plane needs the motion which can get the good power change in the stabilized pose. The second is that the small motion can make good putting in stabilized pose. The third is that the body weight move to the direction of the ball. The fourth is that the putting which looks perfect oscillation is good motion.

• Journal of Life Science
• /
• v.20 no.4
• /
• pp.543-548
• /
• 2010

The purpose of this study was to examine the differences in kinetics between 6 months of rehabilitation training and 12 months of rehabilitation training after total hip arthroplasty. 10 unilateral THA participants performed kinetic tests. Three dimensional kinematics and hip flexors and abductors electromyography (EMG) were collected during each trial. T-test was used for statistical analysis (p<0.05). There was no significant difference in EMG data between the two groups, but the mean comparison EMG data was higher in the 12 months rehabilitation training group than the 6 months rehabilitation training group. The moment value was found with motion-dependent interaction analyzing method which was used by Feltner and Dapena. There was no significant difference between moment values of the two groups. There was no significant difference between ground reaction forces of the two groups; however, there were some differences shown in Fz (vertical reaction force) between the two groups ($892{\pm}104\;N$, $820{\pm}87\;N$). The first peak impact force was about 9% lower in the 12 months group compared to the 6 months group. The second peak active force was nearly equal between the two groups. More research is necessary to determine exactly what constitutes optimal rehabilitation training biomechanics for patients with total hip arthroplasty.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.2
• /
• pp.85-92
• /
• 2011

Evaluation of the removal efficiencies of Fe(II) by reactive sand media coated with manganese (MCS), iron (ICS) and both of iron and manganese (IMCS) was investigated as functions of solution pH ranging from 2 to 9, reaction time and concentration of Fe(II) in a batch reactor using each reactive medium and additional oxidants such as $KMnO_4$ and NaOCl. When only Fe(II) was present in solution without any reactive medium, removal of Fe(II) was quite low below pH 5 due to a slow oxidation of Fe(II) and/or negligible precipitation but greatly increased above pH 5 due to a rapid oxidation of Fe(II) and subsequent precipitation of oxidized Fe species. ICS showed negligible efficiency on the removal of Fe(II) through adsorption. However, an efficient removal of Fe(II) was observed at low solution pH in the presence of IMCS or MCS through rapid oxidation and subsequent precipitation. Removal efficiency of Fe(II) by IMCS in the presence or absence of NaOCl was quite similar. Removal rate of Fe(II) by IMCS and additional oxidants gradually increased as the solution pH increased. From the kinetic experiments, removal pattern of Fe(II) was better described by pseudo-second-order equation than pseudo-first-order equation. A rapid removal of Fe(II) using IMCS in the presence of $KMnO_4$ was observed in the first 10 min. The initial removal rate of Fe(II) using $KMnO_4$ was 14,286 mg/kg hr. In case of using NaOCl, the removal of Fe(II) occurred rapidly in the first 6 hrs and then reached the near-equilibrium state. Removal of Fe(II) on IMCS was well expressed by Langmuir isotherm and the maximum removal capacity of Fe(II) was calculated as 1,088 mg/kg.

• Korean Journal of Ecology and Environment
• /
• v.39 no.4 s.118
• /
• pp.462-470
• /
• 2006

The zooplankton community dynamics and grazing experiments was evaluated along a 40 km section of the lower Seomjin river system. Zooplankton was sampled twice a month from January 2005 to June 2006 at three sites (River mouth; RKO, Seomjin bridge: RK12 and Gurae bridge: RK36) in the main river channel. During the study period, the values of most limnological parameters in the three sites were fairly similar, except for conductivity. Annual variation of conductivity in River mouth and Seomjin bridge was more dramatic than which of the other site. There were statistically significant spatial and seasonal differences in zooplankton abundance (ANOVA, P<0.01). Total abundance of major zooplankton groups at both stations was much higher than in Gurae bridge. Among the macrozooplankton, cladocerans abundance was negligible in study sites during study periods. Community filtering rates (CFRs) for phytoplankton and bacteria varied from 0 to 50 mL $L^{-1}\;D^{-1}$ and from 0 to 45 mL $L^{-1}\;D^{-1}$, respectively. The spatial variation of CFRs for phytoplankton was significant (ANOVA, P<0.05). The CFRs of copepods for phytoplankton and bacteria was much higher than that of cladocerans at study sites. Total zooplankton filtering rates on bacteria were slightly lower than filtering rates on phytoplankton. The CFRs of microzooplankton (MICZ) for bacteria were much higher than for macrozooplankton (MACZ) at all sites. Considering the total zooplankton community, MICZ generally were more important than MACZ as grazers of bacteria and phytoplankton in freshwater zone, while MACZ were more important than MICZ as grazers of phytoplankton in brackish zone.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.3
• /
• pp.179-185
• /
• 2009

In this research, the removal capacity of Cr(VI) by the reused powdered wastes (RPW) containing aluminium oxides was studied. As a pre-treatment process for the preparation of calcined wastes, calcination was conducted at $550^{\circ}C$ to remove organic fraction in the raw wastes. In order to study the adsorption trend of Cr(VI) ions from aqueous solutions, the pH-edge adsorption, adsorption kinetic and adsorption isotherm were investigated using a batch reactor in the presence of four different background electrolytes($NO_3\;^-,\;CO_3\;^{2-},\;SO_4\;^{2-},\;PO_4\;^{3-}$). Cr(VI) adsorption was greatly reduced in the presence of $SO_4\;^{2-}$ and $PO_4\;^{3-}$ over the entire pH range. Meanwhile the inhibition effect by $NO_3\;^-$ and $CO_3\;^{2-}$ was relatively lower than that by $SO_4\;^{2-}$ and $PO_4\;^{3-}$. Cr(VI) adsorption was maximum around pH 4.5 in the presence of $NO_3\;^-$ and $CO_3\;^{2-}$. As the concentration of background electrolytes increased, Cr(VI) adsorption decreased. This result mightly suggests that adsorption between the surface of RPW and Cr(VI) occurs through outer-sphere complex. Cr(VI) adsorption onto the RPW was well described by second-order kinetics. From the Langmuir isotherm at initial pH 3, the maximum adsorbed amount of Cr(VI) onto the RPW was 11.1, 10, 3.3, 5 mg/g in the presence of $NO_3\;^-,\;CO_3\;^{2-},\;SO_4\;^{2-}$, and $PO_4\;^{3-}$, respectively.