• Journal of the Korean Wood Science and Technology
• /
• v.14 no.4
• /
• pp.29-39
• /
• 1986

To investigate the effect of presurfacing, both 25mm rough and pre surfaced oak boards (Quercus grosseserrata BI.) were dried in the same dry kiln condition. Drying curves, drying strains and drying defects of rough and presurfaced boards were compared. The results obatained are as follows. 1. Average drying rate of rough and presurfaced boards from green to 10% M.C. was 0.276%/hr. and 0.284%/hr., respectively. 2. At the early stage of drying, in case of rough boards, maximum tensile strain of outer slices was $-24.2{\times}10^{-4}$mm/mm and maximum compressive strain of innermost slices was $13.0{\times}10^{-4}$mm/mm, and in case of pre surfaced boards, maximum tensile strain of outer slices was $-14.5{\times}10^{-4}$mm/mm and maximum compressive strain of innermost slices was $28.1{\times}10^{-4}$mm/mm. And in both cases, stress reversal occurred at about 40% M.C.. 3. Maximum surface checking appeared at about 40% M.C.. Of the 10 rough boards. 6 hoards contained surface checks, but presurfaced boards did not contained surface checks after drying. And the results of end checking were similar to those of surface checking. But, honeycomb was not found in both cases. 4. Board shrinkage. warp and casehardening of presurfaced boards were similar to those of rough boards. But, collapse of prsurfaced boards was less than that of rough boards.

• KOMUNHWA
• /
• no.69
• /
• pp.5-40
• /
• 2007

The research against Youngdong area Bronze Age settlement structure the condition where the investigation against the area and the remains which are limited becomes accomplished and Only the dwelling site will be investigated from the early settlement of most and recognition there is not a possibility which it will investigate synthetically. The Early settlement to the time which reaches the size of the settlement is small and From Bangnae-ri phases the house possession area increases inside the hill and it follows on south and if dwelling site numbers under increasing, from the aspect where the size of the settlement is magnified seems and it is a position. The Middle settlement currently was confirmed as the beginning from the room village A ruins, it investigates a settlement structure to, the increase of data is necessary. Is Pottery with clay stripes, phases the Later Settlement which Dwelling site, Storeage, Earthenware Kiln, Ditch enclosure and Tomb, the Public dwelling site back large scale Pottery with clay stripes settlement of formation will be investigated from Bangdong-ri settlements which correspond to Songhyun-ri settlement which is a hill characteristic settlement which is located in rivers circumference and the higShland characteristic settlement to provide the data the cultural aspect and character and a settlement structure of Bronze Age postscript and it will be able to grasp.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.549-552
• /
• 2008

The cement is accomplished with CaO, SiO2, Al2O3 and Fe2O3, etc. After pulverizing materials of the limestone, the sand and the clay(shale), iron ore, the cement becomes clinker materials sintering from the rotary kiln of oxidizing atmosphere. The part in the materials of the clinker is substituted with slag, sludge etc. and it is used. because The chromium which is to be included in the clinker materials, in sintering process hexavalent chromium is converted with the chrome. Consequently it changed the type and a content of clinker materials and test hexavalent chromium of the clinkers which is manufactured.

• Journal of Acupuncture Research
• /
• v.23 no.6
• /
• pp.133-143
• /
• 2006

Objectives : To Investigate Severity Measurement and the Correlation between Acupoints on the Face and the Upper limb in Bell's Palsy Patients by Using of DITI. Methods : We recreated the persons in the Wonkwang oriental hospital, KwangJu and the public health center, Hwasoon from April 2005 to October 2005. the 60 persons randomized allocated were not showed the acupuncture and treated in the acupuncture points used for treatment of the shoulder pain. the 30 persons were treated with real acupuncture and the others were treated with Kiln Sham Acupuncture. Conclusion : This report suggest that we must except Kyon-lyo(TE14), kyon-u(LI15), and hu-gye(SI03) from the shoulder pain study with Kim Sham Acupuncture because the persons significantly distinguished Real acupuncture from Sham acupuncture at the Kyon-lyo(TE14), kyon-u(LI15) and hu-gye(SI03) and so We cannot blind a person.

• Journal of the Korean Ceramic Society
• /
• v.53 no.2
• /
• pp.215-221
• /
• 2016

In this study, the utilization of the by-products of various industries was examined using raw materials of CSA high-functional cement such as coal bottom ash, red mud, phosphate gypsum, etc. Technology to improve energy efficiency and reduce $CO_2$ was developed as part of the manufacturing process; this technology included lower temperature sintering ($150{\sim}200^{\circ}C$) than is used in the OPC cement manufacturing process, replacement of CSA cement with the main raw material bauxite, and a determination of the optimum mix condition. In order to develop CSA cement, a manufacturing system was established in the Danyang plant of the HANIL Cement Co. Ltd., in Korea. About 4,200 tons of low purity expansion agent CSA cement (about 16%) and about 850 tons of the lime-based expansion agent dead burned lime (about 8%) were produced at a rate of 60 tons per hour at the HANIL Cement rotary kiln. To improve the OPC cement properties, samples of 10%, 13%, and 16% of CSA cement were mixed with the OPC cement and the compressive strength and length variation rate of the green cement were examined. When green cement was mixed with each ratio of CSA cement and OPC cement, the compressive strength was improved by about 30% and the expansibility of the green cement was also improved. When green cement was mixed with 16% of CSA cement, the compressive strength was excellent compared with that of OPC cement. Therefore, this study indicates the possibility of a practical use of low-cost CSA cement employing industrial wastes only.

• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.583-589
• /
• 2010

In this paper, the properties of reclaimed ash(RA) from various domestic thermal power plants(S, D and H) were analyzed, and the possibility of fabricating the artificial lightweight aggregate(ALA) using RA was studied. The chemical compositions of RA are similar to the clay, but it had higher concentrations of alkali earth metal oxides(CaO, MgO) and unburned-carbon. The TCLP(Toxicity Characteristic Leaching Procedure) results showed that the dissolution concentrations of heavy metal ions of RA were below the limitation defined by the enforcement regulation of wastes management law in Korea. The results of IC analysis showed that leaching concentration of $Cl^-$ ion was 124 ppm for RA of HN and ${SO_4}^{2-}$ ion was leached a few hundreds ppm for all RA in this study. The ALAs with various mass ratio of clay to reclaimed ash(RA:Clay = 7:3, 6:4, 5:5, 4:6, 3:7) were sintered with a electric muffle furnace at the temperature of $1050{\sim}1200^{\circ}C$. The specific gravity and water absorption(%) of the sintered ALAs were 1.1~1.8 and 10~30% respectively. The ALA sintered in the rotary kiln at $1125^{\circ}C$ showed a bulk density of 1.7 and water absorption of 15.2%.

• Applied Chemistry for Engineering
• /
• v.24 no.4
• /
• pp.382-390
• /
• 2013

Foaming process of waste soda lime glasses by just chemical composition control of vitreous feed materials was investigated to find a novel and efficient recycling process. For the chemical composition control of feed materials, 10 wt. parts of $SiO_2$, 0.5 wt. parts of $Na_2SO_4$, 3.0 wt. parts of $B_2O_3$, and 0.3 wt. parts of carbon black as the foaming agent were mixed with 100 wt. parts of soda-lime vitreous feed powder. Proper conditions for foaming process in tunnel kiln are the foaming temperature of $830{\sim}850^{\circ}C$, the foaming time of 30~35 min, and the vitreous feed powder particle size of -325 mesh. Properties of foamed glass blocks obtained under these foaming conditions showed the density of $0.17{\sim}0.21g/cm^3$, thermal conductivity of $0.06{\pm}0.005kcal/h{\cdot}m{\cdot}^{\circ}C$, moisture absorption of 1.1~1.5%, and compressive strength of $20{\sim}30kgf/mm^2$.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.6 s.134
• /
• pp.17-24
• /
• 2005

Korean pine (Pinus koraiensis Sieb.et Zucc.) boards of 30 mm thickness were treated by steaming and four different drying methods. Small specimens were taken from the sapwoods of the treated boards and their longitudinal liquid permeability was measured according to Darcy's law. The specimens were also extracted with alcohol and aceton solutions to examine the mechanism of liquid flow in wood. It was observed that specific permeability drastically decreases with measurement time, resulting in violation of Darcy's law. It may be due to that air bubbles formed under vacuum block flow paths in resin canals. The average specific permeabilities of non-extracted and extracted specimens are different from one treatment to another. It is supposed that the properties of residual resin in resin canals change depending on the conditions of treatments. Anatomical examination was conducted with a scanning electron microscope.

• Journal of the Korean Ceramic Society
• /
• v.49 no.1
• /
• pp.66-71
• /
• 2012

In ancient Goryeo celadon, the effect of the chemical composition and ionic state of Fe on the color was evaluated by Mossbauer spectroscopy and Design of Experiment (DOE) analysis. The ancient celadon pieces excavated from the kiln sites in GangJin and Buan areas were analyzed by Mssbauer spectroscopy, chromaticity, and DOE analysis. The color of celadon was found to be mainly determined by that of glaze since variations of $L^*$, $a^*$, and $b^*$ values for the body were much smaller than those for the glaze. As $Fe^{2+}$/$Fe^{3+}$ in glaze increases, $L^*$ value increases, whereas $a^*$/$b^*$ value decreases, which is well consistent with the result on the synthetic glaze. As the amount of titanium increases in the glaze, the $a^*$ and $b^*$ values decrease; on the other hand, the $L^*$ value increases, which is well consistent with the result on the synthetic glaze.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.12 no.2
• /
• pp.52-60
• /
• 2004

The basic approach to sewage sludge is organic waste minimization, promotion of energy recovery; volume and weight reduction by final treatment, and environmentally final disposal of natural circulation. Dry and pyrolysis of maize was experimentally investigated in full-scale rotary kiln in semi-continuous operation. The operational parameters varied are the operating temperature $160{\sim}175^{\circ}C$ of dry and $450{\sim}800^{\circ}C$ of pyrolysis, the solids residence time 9 min for pyrolysis. Important parameters studied include the running time, water content of sewage sludge, solids amount of sewage sludge(TS%) by the varied temperature. Also, with the increasing of temperature, how the yield of oil and char product change was observed, and the distribution of gas production components was observed. The gas of $C_1{\sim}C_3$ yield increased and oil of $C_4{\sim}C_6$ yield decreased along with pyrolysis temperature of $670^{\circ}C$ by the run time of 9 min.