• The Journal of Engineering Geology
• /
• v.19 no.4
• /
• pp.441-457
• /
• 2009

This study estimated ultimate load by the determination methods based on ultimate load, yield load and settlement using experimental data from static load tests that applied load to driven piles used in sandy grounds at home and overseas until failure appeared markedly. Estimated ultimate load was normalized with actually measured failure load, and was compared among the determination methods according to the characteristics of pile. In addition, I have identified to the determination methods suitable for estimating ultimate load, and reevaluated the safety factor when determining allowable load. From the results of this study were drawn conclusions as follows. Among ultimate loads estimated by the ultimate-load-based determination methods, the value interpreted by Chin's method tended to overestimate actual measurements, and B. Hansen 80% standard and the stability plot method were considered most reliable as their results were closest to actual measurements. According to the results of this study, in calculating the allowable load, if the safety factor to be applied to failing load obtained by the method of determining extreme load is converted to the safety factor applied to the Standards for Structure Foundation Design, a value larger than 3.0 should be applied except the B. Hansen 90% method, and a value larger than 2.0 should be applied in the methods of determining yield load. In addition, if the safety factor to be applied to load obtained by the settlement standard is converted based on safety factor 3.0 for extreme load, a value smaller than 3.0 should be applied to the total settlement standard and the net settlement standard.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.10
• /
• pp.671-677
• /
• 2012

In this study, the characteristics of emulsified fuel and engine emissions were studied with an engine dynamometer. In the results of physical property analysis, the margin of error of net calorific value and gross calorific value was ${\pm}0.5%$, were almost same theoretical calculation and results of physical property analysis test. In emulsified fuel, density and viscosity increased with increasing water contents. Emulsified fuel which is composed of water and Bunker-A was manufactured by using homogenizer and ultrasonic generator in $80^{\circ}C$. Phase separation did not take place in $20^{\circ}C$ and $50^{\circ}C$. In the results of engine dynamometer test, NOx concentration and smoke density were reduced with increasing water contents in using emulsified fuel. Total NOx could be reduced by about 41%, 10%, 32% and 28% at 1,000 rpm, 1,200 rpm, 1,500 rpm and 2,500 rpm respectively. Total smoke density was reduced to 42%, 65%, 70%, 62%, and 82% at 1,000 rpm, 1,200 rpm, 1,500 rpm, 2,000 rpm, and 2,500 rpm respectively.

• Journal of Korean Society of Forest Science
• /
• v.102 no.4
• /
• pp.506-514
• /
• 2013

This study examined the feasibility on the construction of a wood industrialization service center for a wood industry cluster establishment in Jeollanam-do. Construction of the wood industrialization service center is based on a discount rate of 3.5%, an investment period of 4 years, a business operations period of 16 years and an investment cost of 24600 million won; the total amount of the net present value, the cost-benefit ratio and the internal rate of return were assumed to be 2.579 million won, 2.51%, and 10.1%, respectively. In addition, the production inducement coefficient, the induced production effect, the income-induced coefficient, the income inducement effect, the employment inducement coefficient, and the employment inducement effect were estimated 1.4345, 35287 million won, 0.1655, 4000.7 million won, and 0.4665, 1,145 people, in the effects of the wood related industries using the multi-regional input-output model, respectively. Financial independence of operating income to cover its own costs incurred in accordance with the operating project might be practicable.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.54 no.2
• /
• pp.159-164
• /
• 2009

The difference of ginsenosides content according to placement of ginseng planting (line) under shading net in 5-year-old ginseng roots were examined. The total saponin ($Rb_1$, $Rb_2$, Rc, Rd, Re, and $Rg_1$) contents were 15.01 mg/g and 21.79 mg/g in the main roots, 35.93 mg/g and 43.32 mg/g in the lateral roots, 87.85 mg/g and 105.51 mg/g in the fine roots for the front $1st{\sim}2nd$ lines in Yunpoong and Landrace variety (purple-stem variant), respectively. In the middle $3rd{\sim}5th$ lines the total saponin contents were 18.73 mg/g and 23.19 mg/g in the main roots, 44.92 mg/g and 43.50 mg/g in the lateral roots, 92.97 mg/g and 110.70 mg/g in the fine roots in Yunpoong and Landrace variety, respectively. In the rear $6th{\sim}7th$ lines the total saponin contents were 21.88 mg/g and 26.68 mg/g in the main roots, 38.41 mg/g and 44.89 mg/g in the lateral roots, 101.03 mg/g and 107.06 mg/g in the fine roots in Yunpoong and Landrace variety, respectively. The differences in total and individual ginsenosides content in the main, lateral and fine roots among the lines were not significant but total ginsenosides contents in the main roots were different in case of Yunpoong variety. The ratios of protopanaxadiol (PD) type saponin to protopanaxatriol (PT) type saponin in roots were lower in the front lines compared to the middle and rear lines and the ratios were significantly different among the parts of roots.

• The Journal of Pediatrics of Korean Medicine
• /
• v.27 no.4
• /
• pp.87-98
• /
• 2013

Objectives The purpose of this study is to find a literature study of infantile anorexia clinical cases with Traditional Chinese Medicine (TCM) to utilize with Korean medicine treatment methods. Methods 5 TCM journals with the highest impact factors were searched and selected among the journals listed in www.cnki.net. The search keywords were, "Children's Anorexia", "Infantile Apositia", "Infantile Anorexia", "Anorexia Nervosa", and "child of anorexia". he search was limited to the publication date from 2000 to 2012. Results Total 20 studies were selected: Acupuncture (5), Herbal medicine (9), Complex Treatment (3), External Application (2) and Moxibustion (1). Among the Acupuncture related studies, 1 study tested the effect of Sifeng (EX-UE10, 四縫), 3 studies tested the effect of Sifeng (EX-UE10, 四縫) and other acupoints treatment together, and 1 study tested the effect of combination of other acupoints. In all these studies, the study groups showed better therapeutic effects compared to the control groups. The Herbal medicine related studies showed the improvement in appetite and weight as a result of Herbal Medicines treatment. Among the Complex Treatment related studies, 2 studies tested the effect of Acupuncture and Chiropractic co-treatment, 1 study tested the effect of Moxibustion and Herbal medicine co-treatment. In all these studies, symptoms of Infantile anorexia showed significantly improved. Other papers related to External Application and Moxibustion treatment were reported improving in appetite and had other the clinical effects as well. Conclusions Clinical studies testing the effect of TCM for the treatment of Infantile Anorexia have been conducted in small scales, and all the studies showed a certain level of symptom improvement of the patients in the study groups. These results implicate that the methods in Korean medicine can be highly potential treatment options for the treatment of Infantile Anorexia. Accurate and well-controlled studies in large scale would be required to prove the effect of Korean medicine for the treatment of patients with Infantile Anorexia.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.20 no.2
• /
• pp.47-59
• /
• 2017

This study aims to assess offshore wind energy resources around Jeju Island using the InVEST Offshore Wind model. First the wind power density around the coast of Jeju was calculated using reanalysis data from the Korean Local Analysis and Prediction System (KLAPS). Next, the net present value (NPV) for the 168MW offshore wind farm scenario was evaluated taking into consideration factors like costs (turbine development, submarine cable installation, maintenance), turbine operation efficiency, and a 20year operation period. It was determined that there are high wind resources along both the western and eastern coasts of Jeju Island, with high wind power densities of $400W/m^2$ calculated. To visually evaluate the NPV around Jeju Island, a classification of five grades was employed, and results showed that the western sea area has a high NPV, with wind power resources over $400W/m^2$. The InVEST Offshore Wind model can quickly provide optimal spatial information for various wind farm scenarios. The InVEST model can be used in combination with results of marine ecosystem service evaluation to design an efficient marine spatial plan around Jeju Island.

• Nuclear Engineering and Technology
• /
• v.42 no.5
• /
• pp.582-589
• /
• 2010

As a part of the back-end fuel cycle, transportation of spent nuclear fuel (SNF) from nuclear power plants (NPPs) to a fuel storage facility is very important in establishing a nuclear fuel cycle. In Korea, the accumulated amount of SNF in the NPP pools is troublesome since the temporary storage facilities at these NPP pools are expected to be full of SNF within ten years. Therefore, Korea cannot help but plan for the construction of an interim storage facility to solve this problem in the near future. Especially, a decision on several factors, such as where the interim storage facility should be located, how many casks a transport ship can carry at a time and how many casks are initially required, affect the configuration of the transportation system. In order to analyze the various possible candidate scenarios, we assumed four cases for the interim storage facility location, three cases for the load capacity that a transport ship can carry and two cases for the total amount of casks used for transportation. First, this study considered the currently accumulated amount of SNF in Korea, and the amount of SNF generated from NPPs until all NPPs are shut down. Then, how much SNF per year must be transported from the NPPs to an interim storage facility was calculated during an assumed transportation period. Second, 24 candidate transportation scenarios were constructed by a combination of the decision factors. To construct viable yearly transportation schedules for the selected 24 scenarios, we created a spreadsheet program named TranScenario, which was developed by using MS EXCEL. TranScenario can help schedulers input shipping routes and allocate transportation casks. Also, TranScenario provides information on the cask distribution in the NPPs and in the interim storage facility automatically, by displaying it in real time according to the shipping routes, cask types and cask numbers that the user generates. Once a yearly transportation schedule is established, TranScenario provides some statistical information, such as the voyage time, the availability of the interim storage facility, the number of transported casks sent from the NPPs, and the number of transported casks received at the interim storage facility. By using this information, users can verify and validate a yearly transportation schedule. In this way, the 24 candidate scenarios could be constructed easily. Finally, these 24 scenarios were compared in terms of their operation cost.

• Journal of KIISE:Software and Applications
• /
• v.29 no.9
• /
• pp.676-683
• /
• 2002

The success of XML(eXtensible Markup Language) is primarily based on its flexibility : everybody can define the structure of XML documents that represent information in the form he or she desires. XML is so flexible that XML documents cannot be automatically provided with an underlying semantics. Different tag sets, different names for elements or attributes, or different document structures in general mislead the task of classifying and clustering XML documents precisely. In this paper, we design and implement a system that allows checking the semantic-based similarity between XML tags. First, this system extracts the underlying semantics of tags and then expands the synonym set of tags using an WordNet thesaurus and user-defined word library which supports the abbreviation forms and compound words for XML tags. Seconds, considering the relative importance of XML tags in the XML documents, we extend a conventional vector space model which is the most generally used for document model in Information Retrieval field. Using this method, we have been able to check the similarity between XML tags which are represented different tags.

• Journal of Animal Environmental Science
• /
• v.1 no.1
• /
• pp.9-19
• /
• 1995

This study was carried out to investigate the effect of sawdust bedding barn on manure handing, management labour and physiological aspect of dairy cows, and then to establish the criteria on the optimum utilization method of sawdust bedding barn. 46 tie stall barns and 49 sawdust bedding barns were surveyed to cmopare the milk productivity between two different barns, and also 5 tie stall barns, 15 sawdust bedding barns and 1 rice hull bedding barn were selected to study the utilization situation of sawdust barn in Kyung-Ki province area. The major results obtained were as follows; 1. The roof material of sawdust barn were consisted of 66% vinyl house, 23% PVC light and 11% slate and galvanum coated tin. Most of the floor structure was earth ground with the rate of the approximately 82%. 2. The average occupied area of sawdust bed per cow was 15.2 $m^2$, depth that 30 cm and the utilization period was 12 months. 3. Milk Yield was significantly higher at sawdust barn than at tie stall barn(P<0.01). Bacterial and somatic cell count in raw milk were less at the sawdust barn than in tie stall barn. However, there was not significance difference between two barns. 4. The labour hour needed to cow management in the sawdust barn was approximately 48% of that of tie stall barn. 5. The temperature and moisture content measured in sawdust bed were closely affected by seasonal ambient temperature. The skin and hair of cow were much cleaner at the PVC light roofed sawdust barn than any other roof materials. 6. The additives used for improving of fermentation did not show any effect on temperature and moisture content in sawdust bed. When the ambient temperature was $30.4^{\circ}C$, the surface temperature of measured 1 cm above the sawdust bed was $12.2^{\circ}C$ lower and the temperature of 100 cm above the sawdust bed was $2.4^{\circ}C lower under shading net facility than that of vinyl roofed one.7. The hoof length of miking cow was 7.95 cm in tie stall and 9.19 cm in sawdust barn with high significance (P<0.01). And disease occurence such as mastitis and foot-rot tended to decrease in the sawdust barn. 8. The number of total bacteria and coliform bacteria were less in the sawdust bed compared with earth ground resting area. And a parasite strongyloides papillosus was detected but without any infected cow. 9. The nitrate($NO_3N$) content in non-roofed earth ground resting area and earth ground under the sawdust bed was likely to pollute the ground water. 10. In economic point of view, rice hull bedding barn was the cheapest among different systems. And in the sawdust bedding barn PVC light + slate roofed barn was most desirable, and vinyl roofed one the least.

• Journal of KIISE:Information Networking
• /
• v.29 no.3
• /
• pp.286-298
• /
• 2002

The Remote Procedure Call(RPC) has been traditionally used for Inter Process Communication(IPC) among precesses in distributed computing environment. As distributed applications have been complicated more and more, the Mobile Agent paradigm for IPC is emerged. Because there are some paradigms for IPC, researches to evaluate and compare the performance of each paradigm are issued recently. But the performance models used in the previous research did not reflect real distributed computing environment correctly, because they did not consider the evacuation elements for providing security services. Since real distributed environment is open, it is very vulnerable to a variety of attacks. In order to execute applications securely in distributed computing environment, security services which protect applications and information against the attacks must be considered. In this paper, we evaluate and compare the performance of the Remote Procedure Call with that of the Mobile Agent in IPC paradigms. We examine security services to execute applications securely, and propose new performance models considering those services. We design performance models, which describe information retrieval system through N database services, using Petri Net. We compare the performance of two paradigms by assigning numerical values to parameters and measuring the execution time of two paradigms. In this paper, the comparison of two performance models with security services for secure communication shows the results that the execution time of the Remote Procedure Call performance model is sharply increased because of many communications with the high cryptography mechanism between hosts, and that the execution time of the Mobile Agent model is gradually increased because the Mobile Agent paradigm can reduce the quantity of the communications between hosts.