• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.99-103
• /
• 2017

As a development test of the 75-tonf LOx/Kerosene liquid rocket engine for KSLV-II first Stage Engine, hot firing test of 75-tonf engine are performed. The current status of development test on first stage 75-tonf engine system including combustion chamber, turbopump, gas generator, propellant supply system are presented. During the 75tonf engine test campaign, the development of startup sequence of LOx-Kerosene engine system, engine startup using pyrostarter, ignition of gas generator, steady operation and engine shutdown is successfully performed. As a passenger test during engine hot firing tests, Thrust Vector Control system (TVC) of the engine are also evaluated during engine hot firing test. The results of hot firing test of 75-tonf thrust engine system will be used for the design confirmation and performance evaluation of 75 tonf engine system for KSLV-II first Stage.

• Journal of Biosystems Engineering
• /
• v.11 no.1
• /
• pp.24-30
• /
• 1986

In order to collect the engine performance data accurately, rapidly and reliabily, the microcomputer-based engine performance test system was developed and tested. The system measures engine shaft torque and speed, fuel consumption, exhaust gas temperature, engine shaft power and fuel consumption ratio. The system consisted of 32 channels 8 bit A/D converter, time clock, dynamic strain amplifier and signal conditioning circuits to amplify and filter the electrical signal from transducers. Most of transducers were devised for low cost, easy setting and self-manufacturing. The system has been installed on a small kerosene engine (DAEDONG NA50B).

• Aerospace Engineering and Technology
• /
• v.6 no.1
• /
• pp.120-127
• /
• 2007

Performance dispersion in the engine should be considered to predict the flight accuracy of a launch vehicle. A dispersion estimation method was presented with a LOx/Kerosene gas generator cycle engine. The orifices in the propellant supply lines in the engine were assumed to be used for calibration of the performance and the required pressure drops were acquired. The dispersions after calibration were quantified also.

• Journal of Biosystems Engineering
• /
• v.11 no.1
• /
• pp.17-23
• /
• 1986

Speed control of kerosene engine by the combination of a manual throttle and centrifugal weight type governor is not adequate for evaluating energy requirements in laboratory and field performance tests. This paper describes an engine speed control system. This system consists of Apple-II microcomputer, step motor set to the throttle shaft directly, step motor driving and interfacing circuit, engine performance data acquisition system for measuring load, speed and time and potentiometer as speed adjustor. The performance of this system was successful in maintaining engine speed within ${\pm}37$ rpm of reference speed indicated by computer and potentiometer.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.165-169
• /
• 2007

Qualification test range for Lox/Kerosene gas generator cyle liquid rocket engine was determined by considering engine dispersion and flight inlet conditions. With various pump characteristics, the operation range of components and system was investigated through dispersion analysis. The variation of engine performance shows opposite trends in calibration and dispersion.

• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.139-143
• /
• 2003

Study on the ignition characteristics of combustor and gas generator for LOx-kerosene liquid rocket engine was performed experimentally through a series of combustion tests of sub-scale engine combustor and gas generator. Characteristic of gas-torch ignitor based on gaseous methane and gaseous oxygen was compared with hypergolic ignition using propellant tri-ethyl-aluminium. Gas-torch ignitor showed good performance on igniting sub-scale liquid rocket engine combustor and gas generator. It was observed that the ignition delay is also affected by the extent of nitrogen in the combustion chamber.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1060-1060
• /
• 2017

• International Journal of Aerospace System Engineering
• /
• v.5 no.2
• /
• pp.16-22
• /
• 2018

An analysis has been made on the performance variation due to pressure drop change at propellant supply pipes of liquid rocket engine. The objective is to compare the effectiveness of control variables to tune the liquid rocket engine performance. The mode analysis program has been used to estimate the engine performance for different modes which is realized by controlling the flow rate of propellant. The oxidizer of combustion chamber, the fuel of combustion chamber, the oxidizer of gas generator and the fuel of gas generator are the independent variables to control engine thrust, engine mixture ratio and temperature of gas generator product gas. The analysis program is validated by comparing with the powerpack test results. The error range of compared variables is order of 4%. After comparison of tuning effectiveness it is turned out that the pressure drop at oxidizer pipe of gas generator and pressure drop at combustion chamber fuel pipe and the pressure drop at the fuel pipe of gas generator can effectively tune the thrust of engine, mixture ratio of engine and temperature of product gas from gas generator respectively.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.3
• /
• pp.76-83
• /
• 2017

Korea Aerospace Research Institute(KARI) has been developing a new launch vehicle Korea Space Launch Vehicle-II(KSLV-II) with their own technology. Thus, it is required a new launch complex that corresponds to a new propulsion system of launch vehicle. Because widely changing of KSLV-II comparing with KSLV-I such as thrust of engine system, composition of vehicle staging, pneumo-hydraulic scheme of propulsion system, it is important to establishing appropriate ground support equipments for fuel(kerosene) filling. In this critical design process, specific supply line and specification of components are designed and the concept of kerosene filling is determined based on results of preliminary design. Also, plans of supply operation and prerequisite are established and operation algorithms are formed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.3
• /
• pp.62-80
• /
• 2021

The requirements for the next-generation propulsion system and for a good propellant have been summarized. The characteristics and effectiveness of kerosene, hydrogen, and methane, which are the fuels that are mainly attracting attention in Korea and abroad, were compared with each other. As a result of the comparison, methane was evaluated to be more advantageous than other fuels in reliability, cost, reusability, maintenance, eco-friendliness, safety, lifespan, technical difficulties, engine cycle selection, application of common bulkhead, and non-disassembly/reassembly delivery. And in terms of performance, the specific impulse of methane is higher than that of kerosene, so the efficiency of the launch vehicle can be increased. Methane's properties incluidng eco-friendliness, low-temperature combustion, long life, and maintenability make it beneficial for reuse and for the development of multi-purpose engines.