• 대한조선학회논문집
• /
• 제43권4호
• /
• pp.414-421
• /
• 2006

Yacht is operated by wind-driven thrust on the saii, but also experiencing the side force. Thus the keel attached on the bottom of main hull prevents it from flowing sideway. Since the keel affects the stability and thrust of yacht, its selection is one of the most important factor in design. In the present paper the correlation between yacht hull and keel was investigated. through comparison of forces measured at various combinations of heeling and leeway angles with and without keel. Keel-only test was also performed to find out the drag and lift characteristics of keel itself. finally three different types of keel, i.e. fin keel, bulb keel and winglet keel were tested to compare their advantages and drawbacks.

• Structural Engineering and Mechanics
• /
• 제23권3호
• /
• pp.293-308
• /
• 2006

This paper presents a complete and consistent formulation to study the seismic response of a free-standing ship supported by an arrangement of n keel blocks which are all located in a dry dock. It is considered that the foundation of the system is subjected to both horizontal and vertical in plane excitation. The motion of the system is classified in eight different modes which are Rest (relative), Sliding of keel blocks, Rocking of keel blocks, Sliding of the ship, Sliding of both keel blocks and the ship, Sliding and rocking of keel blocks, Rocking of keel blocks with sliding of the ship, and finally Sliding and rocking of keel blocks accompanied with sliding of the ship. For each mode of motion the governing equations are derived, and transition conditions between different modes are also defined. This formulation is based on a number of fundamental assumptions which are 2D idealization for motion of the system, considering keel blocks as the rigid ones and the ship as a massive rigid block too, allowing the similar motion for all keel blocks, and supposing frictional nature for transmitted forces between contacted parts. Also, the rocking of the ship is not likely to take place, and the complete ship separation from keel blocks or separation of keel blocks from the base is considered as one of the failure mode in the system. The formulation presented in this paper can be used in its entirety or in part, and they are suitable for investigation of generalized response using suitable analytical, or conducting a time-history sensitivity analysis.

• 해양환경안전학회지
• /
• 제20권4호
• /
• pp.426-434
• /
• 2014

본 연구에서는 서해안의 해양레저 대중화를 위해 누구나 세일링을 즐길 수 있고, 두 개의 킬로 선체를 지지하여 육상 및 갯벌에서도 선체가 기울지 않고 설 수 있는 트윈킬 요트를 개발하고자 한다. 기존 세일링 요트중 성능이 좋은 편인 블루워터21의 선형을 활용하고 트윈킬 요트의 경우 모노킬 요트보다는 저항성능이 불리할 것으로 예상되므로, 블루워터21의 모노킬 면적 및 무게중심 등을 고려한 트윈킬을 개발하여 모형시험을 수행하였다. 그 결과, 모노킬과 트윈킬의 저항성능에 대한 차이가 약 4 %정도로 예상보다 크지 않음을 확인하였다.

• 수산해양기술연구
• /
• 제50권2호
• /
• pp.147-153
• /
• 2014

The purpose of this paper is to examine the roll damping characteristics by bilge keels on the fishing vessel. Unlike other degree of freedom motions, roll motion is highly nonlinear. However the quantitative evaluation of roll damping combined with waves is very important for the fishing vessel. To reduce roll motion, roll motion stabilizers such as a bilge keel is used due to easy made and cheap cost rather than anti-rolling tank and fin-stabilizer. Authors paid attention to the shape of bilge keel and waves to grasp the roll damping for the fishing vessel and studied about the difference of tendencies of roll angle following the shapes of bilge keel. The model ship was the offshore large purse seiner and four types of bilge keel were used. The data from the experiments were provided and analyzed to investigate the rolling characteristics of the model ship being affected by the wave height, wave period and bilge keel shape. The results of the study showed that three types of the bilge keel have little effective, but only one has an effect on the roll damping. So bilge keel shape and its attachment method need to be a future study for the practical use in fishing vessel.

• 한국해양공학회지
• /
• 제33권6호
• /
• pp.556-563
• /
• 2019

The ice keel gouge and seabed interaction is one of the major considerations in the design of an Arctic pipeline system. Ice keel and seabed interaction engineering models based on experimental data, which give an explicit equation for estimating the ice gouging depth, have been suggested. The suggested equations usually overestimate the ice keel gouging depth. In addition, various types of numerical analyses have been carried out to verify the suggested engineering model equations in comparison to the experimental data. However, most of numerical analysis results were also overestimated compared with the laboratory experimental data. In this study, a numerical analysis considering the contact condition and geostatic stress was carried out to predict the ice keel gouging depth and compared with the previous studies. Considering the previously mentioned conditions, more accurate results were produced compared with the laboratory experiment results and the error rate was reduced compared to previous numerical analysis studies.

• 한국항해항만학회지
• /
• 제30권5호
• /
• pp.375-379
• /
• 2006

세일링요트의 추진시 횡류를 방지하기 위하여 선체 하부에 킬을 부착하게 되는데 이는 세일의 양력에 의한 횡흐름을 멈추게 하는 역할과 힐 모멘트를 없애고 복원력을 생기게 한다. 이는 안전성에 영향을 미치기 때문에 적절한 킬의 선택은 중요하다고 할 수 있다. 또한 킬 하부에 부가물의 부착은 발라스트 중량중심을 낮춤으로서 선체 복원력에 중요한 영향을 미치므로 킬에 대한 최적형상 도출은 매우 중요하다. 이에, 본 연구에서는 저항성능 향상을 위한 동일 침수표면적의 핀킬 하부 부가물에 따른 저항특성을 비교 실험하였다. 실험방법으로는 회류 수조를 이용하여 3가지 핀킬 하부 부가물 모형킬을 모형선에 부착하여 형상별 저항특성을 비교 분석하였다. 분석 결과에 따른 저항감소 최적 형상을 도출 하였다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제19권4호
• /
• pp.601-604
• /
• 2006

The objective of this study was to investigate technical methods for extraction of mucopolysachharide-protein containing chondroitin sulfate from keel cartilage of chickens. The chemical composition of chicken keel cartilage was determined. For the preparation of mucopolysaccharide-protein from lyophilized chicken keel cartilage, hot water extraction and alcalase hydrolysis methods were examined. Results showed that the optimum condition of hot water extraction was incubation for 120 min with a yield of 40.09% and chondroitin sulfate content of 28.46%. For alcalase hydrolysis, the most effective condition was 2% alcalase in 10 volumes of distilled water for 120 min. The yield of hydrolysate was 75.87%, and chondroitin sulfate content was 26.61%. For further separation of chondroitin sulfate from the alcalase hydrolysate, which has a higher yield than that of hot water, 60% ethanol precipitation was performed. The yield of the ethanol precipitate was 21.41% and its chondroitin sulfate content was 46.31%. The hot water extract, alcalase hydrolysate and ethanol precipitate showed similar electrophoretic migration with standard chondroitin sulfate (chondroitin sulfate A), using cellulose acetate membrane electrophoresis. These results indicated that a significant amount of mucopolysaccharide-protein containing chondroitin sulfate could be acquired form chicken keel cartilage. Therefore, keel cartilage in chicken may provide an inexpensive source of chondroitin sulfate for commercial purposes.

• 대한의용생체공학회:의공학회지
• /
• 제19권5호
• /
• pp.519-530
• /
• 1998

본 논문에서는 하지 전단 환자의 보행 성능을 개선하고, 활동성을 증대시긴 목적으로 에너지 저장형 의족의 유연 용골 선계를 위한 기초 연구를 수행하였다. 문헌에서 얻을 수 있는 2차원 시상면에서의 정성걸음새와 인체측정 데이터를 분석하여, 의족의 유연 용골 기초 구조 모델을 제시하였다. 기초 구조 모델은 단순한 빔과 선혈 회전 스프링 ·댐퍼로 구성되었다. 고강도 경량 소재를 의족의 유연 용골 기초 구조에 적용하기 위해 탄소섬유 강화 복합재료를 용골의 기초 구조 소재로 선정하였다. 빔의 형상 변화에 따른 복원변형에너지를 유한요소해석에 의해 계산해내고, 빔형상 변화가 설계변수가 될 수 있음을 제시하였다. 복원변형에너지를 많이 저장할 수 있는 유연 용골 구조의 설계를 위해, 직교배열표를 이용한 조지전 시뮬레이션 계획을 세우고, 유한요소 프로그램인 ABAQUS를 이용하여 계획에 따른 유한요소해석을 수행하고, 분산활석을 통해 효과적인 에너지 저장형 의족의 유연 용골 구조를 얻어냈다. 유연 용골 구조를 이용한 의족걸음새의 동적 시뮬레이션 모델을 완성하고, 한 보행 사이클 동안의 동적 해석을 수행하였다. 그리하여 의족 시스템 개발을 위한 효과적 설계 과정이 제시되었다.

• 대한조선학회논문집
• /
• 제44권4호
• /
• pp.379-388
• /
• 2007

Ever increasing fuel prices and environmental concerns are forcing commercial vessel operators and designers to re-assess current vessel designs with an emphasis on their propulsion systems. The most important parameter determining propulsive efficiency is the diameter of propeller. Many investigations have been carried out to adapt a large and slow turning propeller known as one of the most robust and effective way of achieving high efficiency in ship propulsion system. However, for the same vessel a further increase of propeller diameter would require the modification of the aft end while still paying attention to the hull clearance to prevent excessive propeller excited vibrations. In order to take the advantage of this approach small workboats (e.g. tug boats, fishing vessels etc.) operate in service with a significant increase of aft draught and hence resulting "inclined keel" configuration can be observed. Although it is not unusual to see large vessels sometimes to operate with stern trim to improve their operational performance and fuel efficiency, it is rare to see a such vessel purposely built with an inclined keel feature to fit a large diameter propeller for power saving. This paper investigates the application of the inclined keel configuration to a 3600TEU container vessel with the aim of fitting an 11 % larger diameter propeller (and hence resulting 17.5 % lower rpm) to gain further power saving over the similar size basis container ship with conventional "level keel" configuration.

• 대한조선학회논문집
• /
• 제46권2호
• /
• pp.97-104
• /
• 2009

Ever increasing fuel prices, almost doubled in the last three years, and global pressure to reduce their environmental impact have been enforcing commercial vessel operators and designers to re-assess current vessel designs with emphasis on their propulsion systems and operational practices. In this paper the "Inclined Keel Hull (IKH)" concept, which facilitates to use larger propeller diameter in combination with lower shaft speed rates and hence better transport efficiency, is explored for a modern 3600 TEU container vessel with the aim of fitting an 13 % larger diameter propeller (and hence resulting 20% lower rpm) to gain further power saving over the similar size basis container ship with conventional "level keel" configuration. It appears that successful application of the "inclined keel Hull" concept is a fine balance amongst the maximum gain in propulsive efficiency, minimum increase in hull resistance and satisfaction of other naval architectural and operational requirements. In order to make the concept economically more viable, this paper concentrates on the fore body design with the possible combination of increase of volume in its fore body to recover the expected volume loss in the aft body due to the space for larger propeller and its low wave-making resistance to minimize the efficiency loss using a well-established optimization software.