• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.6
• /
• pp.834-840
• /
• 2014

When the high speed train (KTX) departs from station in the high-speed line, intermittent on-board signal disappearance causes a hindrance of the operation punctuality. Therefore, we have a research objective to verify the causes of hindrance and to find an improvement plan. process of research, when train leaves the station, we applied sand on the rail to improve adhesive power, that sand has an effect on the ATC(Automatic Train Control) signal wave. We detected & analyzed signal waves which is came from detecting device by changing operation condition in accordance with sand material overage detection to be achieved.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.22-27
• /
• 2003

The running safety of the rolling stock depends on the design characteristics and the contact condition between wheel and railway. In this study, the effect of the conicity of wheel tread on the running safety is analyzed. The modal analysis results in $0.5\~0.6Hz$ natural frequency with lateral modes. However, the frequency analysis for the running simulation shows the frequency components near 1Hz. The running simulation shows that the KTX with GV40 wheel has less lateral vibration than that of XP55 as the KTX goes higher speed.

• Journal of the Korean Society for Railway
• /
• v.7 no.3
• /
• pp.259-263
• /
• 2004

The running safety of a railway vehicle depends on the design parameters and contact condition between wheel and rail. In this study, the effect of the conicity of wheel tread is analyzed using ADAMS/RAIL software on running situation. Modal analysis shows in 0.6 Hz natural frequency of lateral mode in fully arranged the KTX cars. The excessive vibration of the tail cars occurs in the 17th car as the speed and the stiffness of the secondary suspension increases, and especially for 1/40 conicity of the GV40 wheel. Also, the analysis shows that combination of wheel profile, GV40 for power cars and XP55 for passenger cars can reduce the lateral vibration of the tail cars.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.6-11
• /
• 2005

During the acceptance test of KTX, lateral vibration of carbody at the tail of the train was found. The carbody lateral vibration was occurred on a straight line in the winter season. We analysis to find the cause of the lateral vibration and the countermeasure. The analysis results show that lateral stiffness of air spring is the most important parameter to cause the carbody lateral vibration. The lateral vibration is occurred at frequency range $0.5{\sim}0.6Hz$ with a negative damping value. We also blow that natural frequency of lateral vibration increase with the train speed up to 1Hz at 300km/h.

• Journal of Environmental Impact Assessment
• /
• v.20 no.4
• /
• pp.443-453
• /
• 2011

The purpose of present study is to develop a noise map around Korean Train Express (KTX) line. It is also to evaluate the high speed railway noise influence in neighboring areas around KTX. In order to develop the noise map, noise source modeling and 3-D noise radiation simulation have been performed by means of SoundPLAN program. The result of the noise map has been verified in comparison with the measured noise level. Noise measurements have been performed at 15 locations around KTX line. At each locations, 6 microphones were located 1.5m and 3m above the ground at each of 25m, 50m and 75 m distances from a center of the KTX track. The noise map showed clearly the high speed railway noise influence in neighboring areas around KTX line. The present study has also showed the noise could be reduced by using noise barriers constructed at severely noise-exposed locations.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.3
• /
• pp.424-430
• /
• 2013

This paper presents a new design works for the braking chopper system which is included in the propulsion system of KTX high speed train. Due to the current fed type synchronous motors used in the propulsion system, some different behaviors are shown comparing to the voltage type other chopper systems. Specially this chopper system acts either braking controlling or regenerative power controlling system with a parallel resistive load in the propulsion system. In this paper, an improved simple high power IGBT brake chopper system has proposed which is able to be replaced with an existing complicated GTO chopper system. The analytical approaches to the parallel load type current chopper system and the propper snubber circuits calculation were explained in this paper to control new chopper system. In addition, the thermal resistance of the cooling system for power dissipation of IGBT modules was calculated also. Finally several PC simulations have been done to clarify its availability.

• Journal of Korean Society of Transportation
• /
• v.22 no.6
• /
• pp.47-54
• /
• 2004

Recently, a large reduction in domestic aviation demand had roughly shown in the range between 34% and 75% in east central and western corridor of Korea. The reasons for the drop in air traffic demand were the provisioning of several new highway serveces and the national economic difficulties. Since April 2004, moreover, the Korea Train Express(KTX) was operated between Seoul and Daegu in the first phrase of 293Km in KTX operational distance and 258Km in air route distance. The operation of KTX significantly impacted air traffic volume, particularly on the overlapped air routes with KTX routes. This study analyzed the effects on air traffic demand in accordance with the opening of KTX by applying the Stated Preference (SP) survey method, the survey conducted prior to 8 months of the KTX initiative. Also, the comparison of the decreased demand forecast by SP analysis and actual revealed traffic volume during two months service after inauguration of KTX was conducted. The Seoul-Daegu route was analysed using the 3 variables considered access and egress time, fare rate, operational frequency. The result obtained from the analysis showed that air users would be preferred only 14%. Comparatively, however, the actual revealed air passengers after the opening KTX were remained 28%, The less "decreased demand" was caused by the instability of the KTX's operation in the initial stage. Therefore, small numbers of passenger were preferable to airservices rather than high speed railroad service.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4D
• /
• pp.565-571
• /
• 2006

This study aimed to analyze access mode choice behavior for KTX Passengers. To fulfill the aims of this study, Dong-Daegu Station was selected as a station for a case study. This study takes place in two stages. These are (i) descriptive statistical analysis of transportation status before and after introduction of the KTX, (ii) empirical model estimation for analyzing access mode choice behavior. This study makes use of the data from travel survey from Daegu metropolitan area. The main part of the survey was carried out in the KTX Dong-Daegu station. The data was collected from a sample of 1,800 individuals. The survey data includes the information on travel from Dong-Daegu station to Seoul. From descriptive statistical analysis of transportation status before and after introduction of the KTX, it is found that revealed demand of the KTX is lower than that expected. Moreover, it is found that the low demand of the KTX stems from high cost for the KTX itself and inconvenience( including travel time and cost) of access mode. In order to analyze mode choice behavior for accessing Dong-Daegu station, multinomial logit model structure is used. For the model specification, a variety of behavioral assumptions about the factors which affect the access mode choice, were considered. From the empirical model estimation, it si found that access travel time and access travel cost are significant in choosing access mode. Given the empirical evidence, we see that improvement of access transportation system for Dong-Daegu station is very important for enhancing the use of KTX.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1647-1650
• /
• 1997

This paper presents the control law of Automatic Rudder Trim System(ARTS) for the KTX-1. The proposed ARTS is designed mainly t reduce the pilot's work load for trimming in the various conditiions of engine torque. airspeed, and aircraft configuration. The ARTS partially compensates the transient yawing motion due to change of engine power in turboprop aircraft because of the limitation of the actuation speed of the trim motor. In this paper flight test data are analyzed to understand the phenomena and the dynamics of the reversible rudder flight control system is derived. Finally, the control concept and conrtol law of ARTS are described and the characteristics of the ARTS are analyzed through simulation study.

• Journal of the Korean Society for Railway
• /
• v.4 no.3
• /
• pp.94-101
• /
• 2001

One of the best methods to evaluate crashworthiness of a full rake trainset is to analyse 1-dimensional dynamic model using dampers, nonlinear springs and bars, and masses. In this study, the crashworthiness of KHST has been evaluated by analysing a nonlinear dynamic model made up of springs/bars-dampers-masses. The numerical results show that the KHST can absorb more kinetic energy at lower impact forces and lower accelerations in case of heavy collisions, if compared with KTX. Also, the KHST can be protected from any damage in its car-body and electric components except the energy absorbing tube in case of light collisions, like train-to-train accidents at speed under 8 kph. On the other hand, the KTX may be more damaged in the light collisions because there is no energy absorbing tube.