• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1138-1142
• /
• 2010

High speed railway structure, contact of vehicle needs to design considering the running stability(dynamic behavior). Also, upper structure has to satisfy design standard about moving load, high speed train(KTX). So, the high speed railway structure has to satisfy the requirement of natural frequency, vertical acceleration on deck, face distortion and vertical displacement considering ride comfort, which is suggested Ho-nam high speed railway design standard. In this study, it was investigated and evaluated to the dynamic behavior for a double-rib arch railway bridge subjected to moving load considering real high speed train loads.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.2
• /
• pp.634-643
• /
• 2010

In this study, both an experimental test and a time history analysis with 3D modeling were performed to verify the structural analysis model in a 2-span two girder bridge of high speed railway, which was under constructed according to the ballast load of track structure. In the basis of the structural analysis model, the analysis of construction step was carried out to investigate the reduction effect of moment in middle support of the bridge which has initial prestressing force according to camber control. The initial prestressing force of proper level was calculated, and then the reduction of moment for economical bridge section was studied. Finally, a bridge analysis method was presented for an economical and efficient design in steel composite bridge.

• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.522-529
• /
• 2005

The commercial service of KTX from April 1st 2004 has realized that whole country has shrunk into half-day life zone and it opened the times of speed. However, some technical problems unexpected before service have been raised and, among them, the noise generation at train passing was claimed by the residents living nearby the track and it is often publicized by the broadcastings and newspapers. In case where the residential area is close to the track, the installation of noise barrier at trackside is the general measures for noise reduction on bridge section and earthwork section. In case of KTX project, such measures were actually taken without any exception; however, the noise level is still high. In this study, analysis for the reason of higher noise level in spite of which the noise barriers are being installed was carried out, the sample of insulation material effective for noise barrier was manufactured and the performance of the insulation material was evaluated to verify its effectiveness

• Journal of the Korean Society for Railway
• /
• v.16 no.4
• /
• pp.305-310
• /
• 2013

In general, it is difficult to measure dynamic responses of a bridge with stepwise increasing speed of a train during commercial service on a high speed railroad. However, before opening the 2nd stage of the Gyeongbu high speed railroad, there was an opportunity for field tests and measurements of the bridge with stepwise increasing speed(from 170km/ h to 315km/h). The measured responses were compared with the results of a developed bridge/train interaction analysis. Although good agreement was found throughout almost the entire range of speeds, relatively large differences were found in the vicinity of the critical speed at which resonance behavior of the bridge occurs. To investigate the cause of this, reanalyses are performed with re-estimated damping ratios from field tests.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.1
• /
• pp.82-87
• /
• 2010

A measurement system of contact force between overhead contact line and pantograph of train is developed which measures the contact force by using four sets of full-bridge strain gauges instead of load cells and accelerometers. The sensors are installed on the pan head of pantograph and the measured data from the sensors are transmitted to a server system in the train by way of wireless Lan. This configuration of the measuring system makes it easy to install on the trains without any alteration of train system. The measurement system is applied to KTX on the Kyungbu high speed line, and the measured contact force data shows good agreement with those measured by load cell and accelerometers. The waveform of the contact force between overhead contact line and pantograph contains essential information about their conditions. The proposed measurement system can probe any defects on overhead contact lines with train running at high speed, which will be a powerful solution for the maintenance of long-distance overhead contact lines.

• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.1180-1187
• /
• 2004

Relative displacements between decks should be within the allowable limit under horizontal forces in high-speed railway bridges. Longitudinal force transmitters(LFT) have been introduced ih high-speed railway bridges for test track. The horizontal forces on the pier supporting the fixed bearing are transmitted to the near piers supporting the sliding bearings by LFT, The performance of LFT was investigated by field test in which the braking and acceleration tests using KTX were conducted in Baebang viaduct. The relative displacements between decks were measured infield test and were compared with the numerical results and the allowable limit.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.772-777
• /
• 2008

Recent development of fiber optic sensors and wireless sensor technology, made structural health monitoring of railway structures cost effective. In this paper, a micro bending fiber optic rail pad sensors are evaluated for train axle force measurement. In order to assess the usability of FBG fiber optic sensors for short-term bridge measurement, the FBG sensors and conventional strain gauges are installed at the same points and the strain results are compared. Also the impact factors are calculated using the FBG strain responses and the results are compared with the conventional sensor responses. A running KTX train was instrumented with wireless sensor system to measure the vibration characteristics and the results are compared with conventional wire sensor system.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.359-364
• /
• 2006

경부고속철도 교량은 대부분 콘크리트교량으로 2@40m와 3@25m의 박스거더교량의 대표적인 형식이다. 일부구간에서 단경간 또는 2경간 연속 50 m 2주형을 갖는 강합성교량이 건설되었다. 연행하는 차륜이 반복해서 통과하는 철도교량은 주기적인 동적하중에 의하여 공진이 발생할 수 있으며, 특히 고속전철이 통과하는 교량은 저속차량이 통과하는 일반철도보다 공진의 발생가능성이 클 뿐 아니라 고속으로 주행하는 열차의 주행안정성 확보를 위해서 엄격한 제한조건을 만족시켜야 하는 엄밀한 동적설계 조건을 갖게 된다. 그러한 조건 중에서 가속도의 제한 규정은 UIC에서 제안된 기준치로서 도상을 갖는 경우에 0.35g이하를 만족시키도록 요구하고 있다. 현재 KTX가 주행하는 교량에서는 일부구간 및 시점에서 규정치를 초과하는 값을 보이고 있는 것으로 계측되었으며, 그 원인 및 대책마련을 위한 연구를 수행하고 있다. 본 연구에서는 그러한 과도한 가속도의 원인 규명을 위한 각종 매개변수 연구와 그 해결책 마련을 위한 연구를 수행하였으며, 경제적이면서도 효과적인 진동저감 방안을 제시하고 있다.

• Journal of the Korean Society of Safety
• /
• v.31 no.6
• /
• pp.45-51
• /
• 2016

The purpose of this study is to investigate the influence of train-induced end rotation of simple supported track girder on the performance of a direct fixation track system (DFTS) in Yeongjong grand bridge. In this study, the influences of deflection of a DFTS and track girder on dynamic rail-track girder interaction forces for the track girder ends currently employed in airport express lines were assessed by performing field tests using actual vehicles running along the service lines. Therefore, the dynamic displacement of rail and track girder and the fastener stress on the center and ends sections of DFTS were measured for two different trains (AREX and KTX) running in Yeongjong grand bridge. A three-dimensional finite element analysis (FEA) model using the time-history function based on the design wheel load was used to predict the train-induced track and track girder displacement, and the FEA and field test results were compared. The analytical results reproduced the experimental results well within about 3-7% difference in the values. Therefore, the FEA model of DFTS on track girder is considered to provide sufficiently reliable FEA results in the investigation of the behavior of DFTS. Using the analytical and experimental results, the influence of train-induced end rotation of simple supported track girder on the interaction behavior of rail and track girder installed on a simple supported track girder ends, i.e., upward displacement of rail-track girder and the fastener stress, was investigated. It was found that the train-induced end rotation effect of track girder was not significantly affected by the upward displacement of rails and the fastener stresses of track girder ends. Further, the interaction behavior of rail and track girder were similar to or less than that of the general railway bridge deck ends, nevertheless the vertical displacement of track was higher than that of conventional DFTS on the general railway bridge. From the results, the dynamic responses of the DFTS on track girder ends were not significantly affected by the safety and stability of DFTS ends.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.4
• /
• pp.125-135
• /
• 2015

The tendency of more longer span length being required economical in railway bridges is studying about PSC I shaped girder. In this case, it is important to analyze and choose the effective girder section for stiffness of bridge. This study investigates the dynamic properties and safety of PSC I shaped girder being used wide upper flange whose selection based on radii and efficiency factor of flexure for railway bridge in different span type. In addition, 40m PSC Box girder bridge adopted in Honam high speed railway is further analyzed to compare dynamic performance of PSC I shaped girder railway bridge with same span length. Time history response is acquired based on the mode superposition method. Static analysis is also analyzed using standard train load combined with the impact factor. Consequently, the result met limit values in every case including vertical displacement, acceleration and distort.