• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.162-170
• /
• 2005

In KSLV-I, actuation system for thrust vector control of kick motor was configured as electro-hydraulic servo actuation system and consisted of actuators, hydraulic power supply system, hydraulic power distribution system and control system. In case of hydraulic power supply system, we use EMDP(Electric Motor Driven Pump) to supply hydraulic power. Generally, we use brushed DC motor for EMDP but it is not easy to operate EMDP using brushed DC motor at a high altitude. Hence, we are developing EMDP using brushless DC motor to use at a high altitude. In this study, we will explain control system for BLDC motor to drive hydraulic pump.

• Aerospace Engineering and Technology
• /
• v.4 no.2
• /
• pp.192-198
• /
• 2005

SI(System Integration) process in KSLV-I development project is integrate whole assemblies which was submitted to system integration supervising team to one complete launch vehicle with proper quality control through test and verification and launch KSLV-I. It is not a one or a few teams' separate job but overall comprehensive job which request all related function group and manufacturing companies' voluntary cooperation. This paper was intended to provide entire SI process outline to whole related function groups and manufacturing companies for better cooperation in SI process and will be revised through continuos discussion among SI supervising group, whole function groups and manufacturing companies.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.769-771
• /
• 2011

The satellite payloaded on the 2nd stage of KSLV-I is planned to perform CCAM(Contamination and Collision Avoidance Maneuver) not to collide with KM(Kick Motor). At the moment, the satellite should pass through low density environment not to be contaminated by KM plume due to residual thrust. Therefore, it is necessary to predict the flow field of KM plume by residual thrust. In this paper, DSMC (Direct Simulation Monte-Carlo) method, which is widely accepted to simulate in rarefied regime, is used to compute the density field of KM plume by residual thrust and the result of DSMC simulation was compared with that of FLUENT to validate it.

• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.117-121
• /
• 2012

Upper stage propulsion system designed for operation in the upper atmosphere should be tested under nozzle full flow conditions to verify its performance on the ground. KARI has carried out high altitude simulation test of KSLV-I kick motor using cylindrical supersonic exhaust diffuser. Also cold and hot flow test for the sub-scaled diffuser have been conducted to verify the design of real scale diffuser and to study its operating characteristics. This paper deals with the results obtained from these high altitude simulation tests.

• Aerospace Engineering and Technology
• /
• v.8 no.1
• /
• pp.66-72
• /
• 2009

In order to verify the operability of a GPS receiver which is one of the KSLV-I onboard electrical equipments under the vacuum conditions, this paper describes the operation methods and performance results of the GPS receiver under the thermal-vacuum and vacuum environments. The damages and degradations of electrical parts of the GPS receiver caused by the pressure change and high-degree vacuum conditions are analyzed in terms of tracking and navigation capabilities through the signal-to-noise ratio and navigation error.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.4
• /
• pp.378-384
• /
• 2011

During the flight test of KSLV-I, various sensors are installed in the launch pad and the flame deflector to measure the flame characteristics and their influences on the launch complex when a launch vehicle lifts off. Parameter Measurement System is responsible for acquiring the above flight test data. The measurement methodology such as the configuration of measurement system, sensor locations and data acquisition procedures are presented. And this paper compares and explains the characteristics of data sets measured during two flight tests.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.3-6
• /
• 2007

Korea Aerospce Research Institute(KARI) has been developing the first civilian rocket, Korea space launch vehicle (KSLV-I), which can put the small size satellite into designated orbit. Developing launch vehicles contains a lot of uncertainty due to large scale, complexity, and technical difficulty. The uncertainty may become risk in the areas of business and technology which causes schedule delay, cost increase, and design changes of subsystems and components. This study describes the technical risk identification methods using FTA and procedures of planning and implementation of risk assessment and reduction of launch vehicle propulsion system.

• Bulletin of the Korean Space Science Society
• /
• 2009.10a
• /
• pp.49.1-49.1
• /
• 2009

Ground Complex, which is located at Naro Space Center, consists of Assembly Complex(AC) and Launch Complex(LC) which is necessary for successful launch of KSLV-I(NARO). AC consists of Assembly/Testing Building(ATB), Payload Processing Building(PPB), Kick Motor Building(KMB). The purpose of AC is accepting of KSLV-I components, testing, checkout, assembly(disassembly) of the launch vehicle(LV), readiness for transferring LV to LC, accepting of integrated Launch Vehicle(ILV) in case of launch cancellation and short/long time storage, and so on. Qualification tests(QT) for the total system at AC are carried out to check hardware used for operations with first stage unit mockup, upper stage unit Mockup and integrated mockup(GTV). The qualification tests is carried out according to program and procedures of QT. By course of this process, AC is certificated that all the systems and facilities of AC are guaranteed by the fulfillment of technological operations envisioned in the program of qualification tests during the work with the mock-up.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.203-206
• /
• 2008

Kick motor(KM) for KSLV-I second stage propulsion system is the main hardware that is necessary for launching satellite to it's track. The mass of the kick motor changes with combustion time because the heat insulator is ablated and propellant is used and slag is piled up. We predicted mass change with the flight time using ground combustion data of KM composed of case, propellant, nozzle, ignitor and slag. The mass prediction of kick motor can be used for calculating the two stage mass and center of gravity history.

• The Science & Technology
• /
• no.8 s.447
• /
• pp.70-73
• /
• 2006