• Journal of the Korean Society of Marine Environment & Safety
• /
• v.15 no.4
• /
• pp.363-367
• /
• 2009

The ship maneuverability is changed by the effects of the bank cushion and the squat in the restricted water area. It is difficult to test the ship maneuverability by the real ship in the restricted water area because of ship's safety. In this study, a numerical model ship was used to simulate the ship's motion and to get information about the bank cushion and the squat in the restricted water area. The less apart from the quay the ship ran, the more ship's heading changed. The greatest change of ship's heading was $22.37^{\circ}$ when a ratio of the length between ship and quay to ship's breadh(=D/B) was 0.2. The squat of the ship was greater in shallower water and at faster speed. The greatest squat was 0.29m when a ratio of water depth to ship's draft(H/d) was 1.25 and ship's speed was 8 knots, the reduced speed was found to be the most important factor in the shallow water area for safety of the ship.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2018.05a
• /
• pp.318-320
• /
• 2018

When a ship sails on sea, it may be influenced by the environmental disturbance such as wind, wave, sea surface temperature, etc. These affect on the ship's speed, fuel consumption, safety and operating performance. It is necessary to find the optimal weather route of a ship to avoid adverse weather conditions which can put the crews in serious danger or cause structural damage to the vessel, machinery, and equipment. This study introduced how to apply A* algorithm based on sea trial test data for determining the optimal ship routes. The path cost function was modelled as a function of minimum arrival time or minimum energy depending on the time of various environment conditions. The specially modelled path-cost function and the safety constraints were applied to the A* algorithm in order to find the optimal path of the ship. The comparison of ship performances estimated by real sea trial's path and estimated optimal route during the voyage of the ship was investigated. The result of this study can be used to create a schedule to ensure safe operation of the ship with short passage time or minimum energy. In addition, the result of this study can be integrated into an on-board decision supporting expert system and displayed in Electronic Chart Display and Information System (ECDIS) to provide all the useful information to ship master.

• Journal of Korea Multimedia Society
• /
• v.15 no.12
• /
• pp.1506-1516
• /
• 2012

In a ship block logistics application, acquisition of locations is required in order to identify location of the ship blocks. A Smart device equipped with a GPS sensor can be used as a mobile client for a ship block logistics application. However the precision of GPS components on a commercial smart device is not high enough. Therefore, using the GPS for localization may produce significant positioning errors in a ship block logistics system. This paper proposes a method to reduce errors in measuring locations using a smart device. Based on the knowledge of how the location information is used in a ship block logistics application, and the predictability of the client's moving line based on geographical layout of a shipyard area, our proposed technique enables a better prediction of the ship blocks location. Performance evaluation shows that the proposed technique can significantly reduce the positional error.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.54 no.3
• /
• pp.231-238
• /
• 2018

In this study, a ship motion control system design method is introduced for autonomous ships. Some related research results and technologies for autonomous ships have already been developed and applied to ships. For example, the Norwegian Maritime Authority and the Coastal Administration have signed an agreement that allows to test of autonomous ships in the defined area (port to port). Many countries and industries are pursuing to realize the autonomous vessel in the real world. In this paper, the authors try to develop related technology. As basic research, a ship model of the pilot vessel is developed and physical parameters are identified by experiment and simulations. Using the mathematical ship model, a control system is designed and control performance is evaluated by simulations.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.1
• /
• pp.1-9
• /
• 2015

Stability criterion and its calculation are the crucial issue in the application of sail-assisted ship. However, there is at present no specific criterion and computational methods for the stability of sail-assisted ship. Based on the stability requirements for seagoing ships, the stability criterion of the sail-assisted ships is suggested in this paper. Furthermore, how to calculate the parameters and determine some specific coefficients for the ship stability calculation, as well as how to redraw stability curve are also discussed in this paper. Finally, to give an illustration, the proposed method is applied on a sail assisted-ship model with comments and recommendations for improvement.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2015.10a
• /
• pp.37-39
• /
• 2015

The ships transiting the Northern Sea Route (NSR) have been gradually increased so that the number of ship-ice collision accidents would be increased. The collision between ship and ice floe can lead to serious damage of hulls and decline of ship's maneuverability. In this study, collision tests that a model ship is forced to collide with disk-shaped synthetic ice floes are conducted in a towing tank. The synthetic ice floes made of polypropylene which has similar density with real ice are used. The ice load is measured by a load cell installed on the carriage rod. The ice floe's motion is measured by a motion sensor installed on the synthetic ice floe. The influences of contact conditions such as hull form and ship speed on the ship-ice collision response are investigated and discussed by measured peak force and ice floe's motion.

• Journal of Fisheries and Marine Sciences Education
• /
• v.28 no.1
• /
• pp.14-21
• /
• 2016

Research on ship motion and seasickness is recognized as the important research area to ensure the pleasant operative environment in addition to the research of operation safety of ship. In this paper, the motion performance in waves for the training ship Kaya of Pukyong National University is obtained by using the computer program based on Strip Method. To guarantee the pleasant seafaring in ocean, the vertical acceleration of ship motion is calculated according to the habitation division location in the ship. The results of calculation by changes of location of habitation division are compared with the guideline of MSI(Motion Sickness Incidence). The degree of motion sickness is shown and discussed through the comparison between calculated vertical acceleration spectrum and MSI guideline. To improve the safety of ship in motion and the pleasant seafaring in waves, the downtrend of seasickness ratio is needed by the decrease on vertical acceleration of the ship. Through the results in this paper, the relocation of both bridge and accommodation toward the aftship reduced the vertical acceleration and MSI.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.2 s.146
• /
• pp.164-170
• /
• 2006

To improve ship's maneuverability and carry out special goal POD propulsion system was equipped as propulsion and maneuvering system. To predict the maneuverability of a ship with POD propulsion system HPMM tests and POD open water test are carried out. In this paper modular model with 4 degree of freedom of a ship with twin POD propulsion system is presented. To use modular model the forces of POD propulsion system are measured separately from the hull forces. The measured forces and moments are analyzed by using modular model and whole ship model The simulation results of modular model are compared with those of whole ship model. From the present study it is Possible to analyze HPMM tests of a ship with twin POD propulsion system by modular model.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.06a
• /
• pp.205-218
• /
• 2000

Hull forms of Jiao Yi Ship for shipping and foreign trade in Silla and Tang Dynasty were transformed and developed in accordance to their voyage and rational routes. The trade ship was a sea ship, used by Chang Po Go's, the Silla great sea merchant ship, in the marine trade with China during the 8th and 9th century. It is not easy to presume the hull type and trade formal of Chang Po Go's Jiao Yi Ship of the 8th and 9th Century. Studying on the ship type of the trade ship is the urgent problem to be solved, in the sphere of leaning about the history of communication between China and Korea. The authors take the initial prove into this subjects, by researching Chang Po Go's marine activities, and point out that the trade ship's original type should be the Sha Ship which was the sea ship sailing th sea in northern China, in the Tang Dynasty. This study aims to present materials concerning hull forms of Chang Po Go's Jian Yi Ship by analysing ancient voyage history, foreign trade history, and ship history of Silla, Tang and Japan during the 8th and 9th century.

• Journal of Ship and Ocean Technology
• /
• v.9 no.3
• /
• pp.23-32
• /
• 2005

Ship STEP(Standard for the Exchange of Product Model Data) which is composed of AP 215 (Ship Arrangement), AP 216(Ship Hull Form), AP 218 (Ship Structure), has been developed more than last 10 years and it is now at the stage just before IS(International Standard). It is expected that ship STEP would be used for the seamless data exchange among various CAD/CAM/CAE systems of shipbuilding process. In this paper the huge and complicated data structure of ship STEP is briefly reviewed at the level of ARM(Application Reference Model) and some abstract test cases which will be included as part of the standards are introduced. Basically ship STEP has common data model to be used without losing compatibility among those three different ship AP's, and it is defined as the modeling framework. Typical cases of data exchange during shipbuilding process, such as hull form data exchange between design office and model basin, midship structure data between shipbuilding yard and classification society are reviewed and STEP physical data are generated using commercial geometric modeling kernel. Test cases of ship arrangement at initial design stage and hydrodynamic data of crude oil carrier are also included.