• Journal of Oral Medicine and Pain
• /
• 제31권3호
• /
• pp.265-274
• /
• 2006

Temporomandibular joint (TMJ) internal derangement, especially disc displacement with reduction (DDwR) is the most common TMJ arthropathy and has been thought to do some effects on masticatory performance. Measuring of maximal bite force has been widely used as objective and quantitative method of evaluating masticatory performance, but previous studies showed various results due to various characteristics of subjects and different measuring devices and techniques. In a few studies about the correlation of bite force and temporomandibular disorders (TMD), some authors reported that bite force and masticatory performance would be reduced in patients with TMD because of pain. But the correlation of changes in structure of articular disc and masticatory performance has not been well investigated yet. In this study, to investigate the influences of non-painful disc change on the masticatory performance, we measured the value of maximal bite force, occlusal contact area and occlusal pressure of 39 patients with non-painful DDwR of the TMJ using pressure sensitive film, and compared it with that of 59 controls. The results are summarized as follows: 1. The maximal bite force (P<0.01) and the occlusal contact area (P < 0.05) of the DDwR patients were greater than the controls. 2. There was no significant difference in occlusal pressure between the DDwR patients and the controls (P > 0.05). 3. The maximal bite force of the male group was greater than that of the female group (P < 0.05). However, the occlusal contact area and the occlusal pressure between the male and the female group didn't show significant difference (P > 0.05). From the results above, we can suggest that DDwR could be a factor of changing bite force, but more controlled, large scaled and EMG related further study is needed.

• Journal of Dental Rehabilitation and Applied Science
• /
• 제21권1호
• /
• pp.1-14
• /
• 2005

The purpose of this study was to assess the loading distributing characteristics of implant prosthesis of internal connection system(ITI system) according to position and direction of load, under vertical and inclined loading using finite element analysis (FEA). The finite element model of a synOcta implant and a solid abutment with $8^{\circ}$ internal conical joint used by the ITI implant was constructed. The gold crown for mandibular first molar was made on solid abutment. Each three-dimensional finite element model was created with the physical properties of the implant and surrounding bone. This study simulated loads of 200N at the central fossa in a vertical direction (loading condition A), 200N at the outside point of the central fossa with resin filling into screw hole in a vertical direction (loading condition B), 200N at the centric cusp in a $15^{\circ}$ inward oblique direction (loading condition C), 200N at the in a $30^{\circ}$ inward oblique direction (loading condition D) or 200N at the centric cusp in a $30^{\circ}$ outward oblique direction (loading condition E) individually. Von Mises stresses were recorded and compared in the supporting bone, fixture, and abutment. The following results have been made based on this study: 1. Stresses were concentrated mainly at the ridge crest around implant under both vertical and oblique loading but stresses in the cancellous bone were low under both vertical and oblique loading. 2. Bending moments resulting from non-axial loading of dental implants caused stress concentrations on cortical bone. The magnitude of the stress was greater with the oblique loading than with the vertical loading. 3. An offset of the vertical occlusal force in the buccolingual direction relative to the implant axis gave rise to increased bending of the implant. So, the relative positions of the resultant line of force from occlusal contact and the center of rotation seems to be more important. 4. In this internal conical joint, vertical and oblique loads were resisted mainly by the implant-abutment joint at the screw level and by the implant collar. Conclusively, It seems to be more important that how long the distance is from center of rotation of the implant itself to the resultant line of force from occlusal contact (leverage). In a morse taper implant, vertical and oblique loads are resisted mainly by the implant-abutment joint at the screw level and by the implant collar. This type of implant-abutment connection can also distribute forces deeper within the implant and shield the retention screw from excessive loading. Lateral forces are transmitted directly to the walls of the implant and the implant abutment mating bevels, providing greater resistance to interface opening.

• Journal of the Korean Society for Precision Engineering
• /
• 제24권8호통권197호
• /
• pp.122-129
• /
• 2007

To evaluate the effect of artificial disc implantation and fusion on the biomechanics of adjacent motion segment, a nonlinear three-dimensional finite element model of whole lumbar spine (L1-S1) was developed. Biomechanical analysis was performed for two different types of artificial disc, ProDisc and SB $Charit{\acute{e}}$ III model, inserted at L4-L5 level and these results were also compared with fusion case. Angular motion of vertebral body, forces on the spinal ligaments and facet joint under sagittal plane loading with a compressive preload of 150 N at a nonlinear three-dimensional finite element model of Ll-S1 were compared. The implant did not significantly alter the kinematics of the motion segment adjacent to the instrumented level. However, $Charit{\acute{e}}$ III model tend to decrease its motion on the adjacent levels, especially in extension motion. Contrast to motion and ligament force changes, facet contact forces were increased in the adjacent levels as well as implanted level for constrained instantaneous center of rotation model, i.e. ProDisc model.

• Korean Journal of Applied Biomechanics
• /
• 제28권3호
• /
• pp.175-180
• /
• 2018

Objective: Anterior cruciate ligament reconstruction (ACLR) has been considered the primary treatment for anterior cruciate ligament (ACL) injured patient. However, there is little biomechanical evidence regarding bilateral knee joint biomechanics during landing and cutting task after ACLR. Method: Eighteen females with ACLR participated in this investigation. Double leg jump landing (DLJL) and single leg jump cut (SLJC) biomechanics were assessed. Results: During DLJL, the healthy knee showed greater knee valgus angle at initial contact ($^{\circ}$) compared to the injured knee (Injured: $2.93{\pm}2.59$, Healthy: $4.20{\pm}2.46$, t=2.957, p=0.009). There was a significant difference in anterior tibial shear force ($N{\times}N^{-1}$) with greater in the injured knee (Injured: $1.41{\pm}0.39$, Healthy: $1.30{\pm}0.35$, t=2.201, p=0.042). During SLJC, injured knee showed greater knee extension moment ($N^*m{\times}[N^*m]^{-1}$) compared to healthy knee (Injured: $0.51{\pm}0.19$, Healthy: $0.47{\pm}0.17$, t=2.761, p=0.013). However, there was no significant differences between the knees in the other variables. Conclusion: ACLRfemales exhibited a greater knee valgus angle at initial contact and lesser anterior tibial shear force on the healthy knee during double leg jump landing. In addition, ACLR females showed a greater knee extension moment on the injured knee during single leg jump cut.

• Korean Journal of Applied Biomechanics
• /
• 제21권1호
• /
• pp.31-38
• /
• 2011

This study aimed to determine the effects of the blockage of visual feedback on joint dynamics of the lower extremity. Fifteen healthy male subjects(age: $24.1{\pm}2.3\;yr$, height: $178.7{\pm}5.2\;cm$, weight: $73.6{\pm}6.6\;kg$) participated in this study. Each subject performed single-legged landing from a 45 cm-platform with the eyes open or closed. During the landing performance, three-dimensional kinematics of the lower extremity and ground reaction force(GRF) were recorded using a 8 infrared camera motion analysis system (Vicon MX-F20, Oxford Metric Ltd, Oxford, UK) with a force platform(ORG-6, AMTI, Watertown, MA). The results showed that at 50 ms prior to foot contact and at the time of foot contact, ankle plantar-flexion angle was smaller(p<.05) but the knee joint valgus and the hip flexion angles were greater with the eyes closed as compared to with the eyes open(p<.05). An increase in anterior GRF was observed during single-legged landing with the eyes closed as compared to with the eyes open(p<.05). Time to peak GRF in the medial, vertical and posterior directions occurred significantly earlier when the eyes were closed as compared to when the eyes were open(p<.05). Landing with the eyes closed resulted in a higher peak vertical loading rate(p<.05). In addition, the shock-absorbing power decreased at the ankle joint(p<.05) but increased at the hip joints when landing with the eyes closed(p<.05). When the eyes were closed, landing could be characterized by a less plantarflexed ankle joint and more flexed hip joint, with a faster time to peak GRF. These results imply that subjects are able to adapt the control of landing to different feedback conditions. Therefore, we suggest that training programs be introduced to reduce these injury risk factors.

• Structural Engineering and Mechanics
• /
• 제6권1호
• /
• pp.63-76
• /
• 1998

This paper presents dynamic responses of structures with sliding base which limits the translation of external loads from ground excitation. A discrete element model based on the discontinuous deformation analysis method is proposed to study this sliding boundary problem. The sliding base is simulated using sets of fictitious contact springs along the sliding interface. The set of contact spring is to translate friction force from ground to superstructure. Validity of the proposed model is examined by the closed-form solutions of an idealized mass-spring structural model subjected to harmonic ground excitation. This model is also applied to a problem of a three-story structural model subjected to the ground excitation of 1940 El Centro earthquake. Analyses of both sliding-base and fixed-base conditions are performed as comparisons. This study shows that using this model can simulate the dynamic response of a sliding structure with frictional cut-off quite accurately. Results reveal that lowering the frictional coefficient of the sliding joint will reduce the peak responses. The structure responses in little deformation, but it displaces at the end of excitation.

• Journal of the Korean Society of Industry Convergence
• /
• 제18권3호
• /
• pp.167-172
• /
• 2015

In this paper, we propose a new approach to design and control a smart gripper of robot system. A control method for flexible grasping a object in partially unknown environment was proposed, where a proximate sensor detecting the distance between the fingertip and object was used. Based on the proximate sensor signal the finger motion controller could plan the grasping process divided in three phases. The first step is scanning process which two first joints were moved to mid-position of the detected range by a state-variable feedback position controller, after the scanning was finished. The contact force of fingertip was then controlled using the detection sensor of the servo controller for finger joint control. The proposed grasping planning was tested on rectangular bar.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제37권10호
• /
• pp.953-959
• /
• 2013

In this study, a multibody dynamic model of the cervical spine was developed for a virtual in-vitro cadaveric experiment. The dynamic cervical spine model was reconstructed based on Korean CT images and the material properties of joints and soft tissue obtained from in-vitro experimental literature. The model was validated by comparing the inter-segmental rotation, multi-segmental rotations, load-displacement behavior, ligament force, and facet contact force with the published in-vitro experimental data. The results from the model were similar to published experimental data. The developed dynamic model of the cervical spine can be useful for injury analysis to predict the loads and deformations of the individual soft-tissue elements as well as for virtual in-vitro cadaveric experiments.

• Korean Journal of Applied Biomechanics
• /
• 제20권1호
• /
• pp.67-73
• /
• 2010

The purpose of this study was to compare the differences in kinematic and kinetic parameters of the ankle and knee joint according to three landing direction(central, left, right). Fifteen collegiate male athletes(age: $22.7{\pm}3.5$ years, height: $174.9{\pm}7.1\;cm$, weight: $69.4{\pm}6.7\;kg$) with the right leg as dominant were chosen. The subjects performed series of drop landings in three directions. In terms of the three different landing directions, plantar flexion was the greatest during the central drop landings. For each initial contact of the landing direction, plantar flexion of the ankle was greatest at the central drop landing, inversion of the ankle was greatest at the right landing and valgus of the knee was greatest at the left drop landing. Regarding the peak force, the greatest was at the 1st peak force during the central drop landing. For the time-span of the 2nd peak force and the 2-1 peak force, both right sides resulted as the greatest. Therefore, with the appropriate training in landing techniques and developing neuromuscular training for proprioception by taking the injury mechanisms on ankle and knee during drop landings into account, it will assist in preventing such injuries.

• The Journal of Korean Academy of Prosthodontics
• /
• 제39권4호
• /
• pp.366-375
• /
• 2001

The objective of this study was to investigate the surface contact and screw joint stability between screw and implant interface by use of sealer. The implants evaluated in this study were Steri-Oss futures(Hexlock $3.8D{\times}10mm$: Steri-Oss, Yorba Linda, CA), and Steri-Oss staight abutment. Titanium alloy screws were used to secure abutments to implants. The other titanium alloy screws applicating sealer(Impla-Seal, Implant Support Systems, Inc. Irvine, CA) were used to secure abutments to implants. In one another sample, 6kg of force was applied during simulated intraoral movements after abutment screws were secured to the implants with sealer. All samples were cross sectioned with sandpaper and polished with $0.1{\mu}m\;Al_2O_3$. Then samples were recorded with an scanning electron microscope. The results were as follows : 1. In the case of titanium alloy screw, irregular contacts and relatively large gap were present at thread mating surface. Also abutment screw/implant interface demonstrate incomplete seating and only one surface contact of threads between implant and screw. 2. In the case of titanium alloy screw applecating sealer, sealer was present between implant and screw. Therefore implant and screw had relatively close and tight contact without the presence of large gap. 3. On the other hand, in the case of titanium alloy screw applicating sealer and dynamic loading of suprastructures, sealer was partially present between implant and screw. Conclusively, sealer fills voids, creating a barrier to moisture and bacteria. In addition, loading of suprastructures may change the situation and limit the indications for gap sealing.