• Journal of Welding and Joining
• /
• 제18권1호
• /
• pp.91-96
• /
• 2000

Characteristics of the weld defect, such as a blowhole and a pit in lap-jointed fillet Co₂ welds of Zn-coated steel sheet were studied in order to make clear the sequence of the blowhole formation during welding. Main conclusions obtained are as follows: 1) Blowhole, wormhole and pit were found in fillet welds, although the optimum welding condition of 200A-23V-100cm/min was applied. 2) Zn was only detected at the solidification boundary at the early stage of the blowhole formation. 3) Most of the blowholes was started to form at lap-joint by the Zn vapor. With increasing of the Zn vapor and its pressure, the blowhole was develope to th bed surface until the completion of weld solidification. 4) The behavior of the blowhole in growth was similar to that of the columnar dendrite during welding.

• 한국소음진동공학회논문집
• /
• 제20권8호
• /
• pp.761-766
• /
• 2010

The goal of this study is to analysis natural frequency for different static postures of human leg. To perform this research human leg is modeled by multi-body modeling for the musculoskeletal system. This leg model has biarticular muscles which acting on two joints and the muscles represents some of the major muscles, such as hamstring, of the upper and lower limbs. To obtain each static equilibrium position energy method is employed and to analysis natural frequency linearization method for constrained mechanical system is employed. Static equilibrium position depends on some parameter or condition such as hamstring stiffness or external force. Making a change these parameter the aim of this research can be performed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1948-1953
• /
• 2005

The Teakwondo is composed of the breaking, competition and poomsea. In the hand breaking, the breaking impact of human is affected by the breaking posture. In this paper, impact analysis of the human model for breaking posture is carried out. The LifeMOD is used in breaking modeling and simulation. The simulation model createsthe human model to hit and to grasp a pine board. For the breaking, the poomsea motion of the hand joint inputs the splines pass condition. As the results, the reaction of human joint is presented

• Journal of Welding and Joining
• /
• 제14권1호
• /
• pp.82-91
• /
• 1996

The maximum butt-joint gap size in $CO_2$ laser beam welding of SAPH steel plates with different thicknesses and its bending formability were studied. In the range of the gap size$\geq$0.1mm, the optimal butt welding speed was faster than that of no gap (air gap) condition. This behaviour was independent on the difference of thickness at any combination. Also, the allowable gap size in steel plates with different thicknesses was larger than with same thicknesses. In the range of $T/T_0$(bead shape) $\geq$ 0.8, good bending formability was obtained at any combination of thickness. The formability was improved by reducing the hardness in weld bead using pre-heating process. Finally, FEM result of the laser beam welded underframe with different thicknesses was compared to that of the conventional spot welded underframe.

• Journal of Welding and Joining
• /
• 제21권4호
• /
• pp.69-74
• /
• 2003

The mechanical properties of STD11 Joints by using TLP (Transient Liquid Phase Diffusion) bonding method employing MBF-30 and MBF-80 insert metals were investigated with concerning to the microstructural change. TLP bonding of STD 11 was carried out at 1323∼1423K for 0.6ks∼3.6ks in vacuum. The microstructure and the element distribution of the interlayer between tool steels and insert metals showed specific feature with bonding conditions. It was found that the width of the interlayer increased at initial bonding stage. However, the width of interlayer showed nearly constant value during the isothermal solidification. After isothermal solidification was completed, the joint showed homogeneous element distribution and similar microstructure with base metal because of the grain boundary migration to the bonded interlayer. The bonding strength measured by a tensile test has been varied with the bonding conditions. The maximum joint strength, 760MPa, was obtained with the condition of 1423K for 1.2ks using MBF30 insert metal in this experiment.

• 대한인간공학회지
• /
• 제29권5호
• /
• pp.727-734
• /
• 2010

The objective of this study was to evaluate the resting postures of the fingers and wrist based on the biomechanical model in term of hand posture (neutral, pronation, and supination) and gender (male and female). The finger and wrist joint angles were measured with VICON motion system. The EMG system was used to examine the muscle activity in the resting condition. The participants consisted of twenty male and twenty female students. The angles of the fingers and wrist were analyzed by means of the coordinate system associated with the International Society of Biomechanics. Hand posture was significant for all the joints. The finger and wrist joint flexed in supination more than in neutral and pronation. The hand posture and gender were not significant for the results of muscle activity, but it had larger muscle activities in supination more than in neutral and pronation.

• Journal of the Korean Wood Science and Technology
• /
• 제21권1호
• /
• pp.51-58
• /
• 1993

The phenol resorcinol formaldehyde resin (PRF) adhesives which are curing at ambient temperature for structural purposes were synthesized. A PRF resin is produced according to the two-stage reaction system. In first stage, a low-condensed resol or methylolated phenol were prepared from phenol by reaction with a formaldehyde in alkaline condition. The molar ratio of phenol to formaldehyde was 1.0~1.4. And in second-stage, resorcinol was added to combine with the methylol group of a low-condensed resol(R/P molar ratio 0.3). The glue-joint strength, pot-life and workability of this synthetic PRF resin were superior to conventional ambient temperature setting adhesives such as oilic urethane or water based polymer-isocyanate resin for wood adhesives.

• 대한족부족관절학회지
• /
• 제13권2호
• /
• pp.203-206
• /
• 2009

We experienced a case of congenital insensitivity to pain with anhidrosis mimicking a chronic osteomyelitis of the talus, with recurrent ankle swelling and intermittent fever. He was misdiagnosed as low virulence osteomyelitis at other hospital in annual recurrence for 3 years. A Charcot joint in children is a very rare condition and diagnosis should be made in a careful approach.

• Journal of Korean Neurosurgical Society
• /
• 제54권6호
• /
• pp.537-539
• /
• 2013

Charcot spinal arthropathy is a rare, progressive type of vertebral joint degeneration that occurs in the setting of any preexisting condition characterized by decreased afferent innervation to the extent that normal protective joint sensation in the vertebral column is impaired. The authors report on a case of Charcot arthropathy of the lower lumbar spine mimicking a spinal tumor following cervical cord injury.

• 한국통신학회논문지
• /
• 제15권9호
• /
• pp.764-774
• /
• 1990

알고리즘 구조가 간단하고 실제적 응용이 쉬운 LMS 알고리즘을 이용한 적응 필터 설계에서 횡단필터, 격자필터 및 결합처리 격자필터의 예측기 특성을 비교 연구하였다. 실제적 설계를 위해 각 필터의 LMS 알고리즘의 이론적 배경과 구성을 보였고 최적 가중치 벡터와 반사계수의 적응 수렵조건을 명시하였으며 이를 컴퓨터 시뮬레이션을 통하여 나타내었다. 또한 정지및 비정지 입력 신호에 대한 이들 필터의 오차신호 특성과 잡음특성을 비교하였고 결합처리 격자필터가 이들 LMS 알고리즘을 이용한 적응 필터에서 가장 우수한 특성을 갖고 있음을 보였다.