• Journal of the Korean Society of Physical Medicine
• /
• v.17 no.4
• /
• pp.85-92
• /
• 2022

PURPOSE: This study examined the effects of motion taping during combined lower extremity exercise application on pain, ROM, muscle strength, and WOMAC index in middle-aged women with osteoarthritis of the knee joint METHODS: The subjects were 26 middle-aged women with osteoarthritis in the knee joint. Twenty-six subjects were divided into two groups. Each group contained 13 subjects. Three subjects dropped out in the middle of the experiment. The intervention was six weeks, three times a week. The control group performed traditional physical therapy and lower extremity exercise. The experimental group was motion taping applied to the lower extremity exercise. The measurement factors were knee joint pain, quadriceps muscle strength, and WOMAC index. The pain was measured using the numeric pain scale instrument (NPSI). The quadriceps strength was measured using the 1RM method. RESULTS: In both groups, pain, muscle strength, and WOMAC index showed significant improvement according to the intervention (p < .05). In comparison between groups of the change values pre-post intervention, pain and WOMAC index showed statistically significant differences between the two groups. On the other hand, there was no difference in strength between the two groups. CONCLUSION: When performing a rehabilitation exercise program for middle-aged women with osteoarthritis of the knee, motion taping has a positive effect on pain and the WOMAC index.

• Journal of The Korean Society of Integrative Medicine
• /
• v.10 no.3
• /
• pp.63-72
• /
• 2022

Purpose : Several studies have investigated the effects of dynamic stretching (DS) and self-mobilization (SM), however, studies comparing the two interventions are rare. Therefore, the purpose of this study was to compare the effects of DS and SM on ankle strength, dorsiflexion range of motion (DFROM), and balance to determine which is superior. Methods : Thirty-two healthy young adults participated in this study. Participants were randomly assigned to two groups (SM and DS). DS was performed for the purpose of stretching the medial gastrocnemius muscle. For the SM group, ankle joint SM was performed in three ways. For all participants, the following measurements were performed as pre- and post-tests: isometric strength of dorsiflexor and plantar flexor, weight-bearing lunge test (WBLT) to evaluate DFROM, Tetrax system to evaluate static balance, and y balance test (YBT) to evaluate dynamic balance. Differences before and after the intervention within each group were compared using paired t-test. Also, the variable's variation was compared between groups using an independent t-test. Results : Significant differences were found in ankle dorsiflexor strength, WBLT, YBT, weight distribution index (WDI) (pillow and opened eyes; PO), and stability index (ST) (normal and closed eyes; NC) before and after intervention in the SM group (p<.05). In the DS group, significant differences were found in ankle dorsiflexor and plantar flexor strength, WBLT, YBT anterior, WDI (normal and opened eyes; NO, PO), and ST (NO, NC, PO, pillow and closed eyes) before and after the intervention (p<.05). Ankle plantar flexor strength and WDI (PO) were significantly different between groups. Conclusion : Based on the results of this study, DS or SM can be considered as a possibility for selective use according to variables for improving ankle joint function (DFROM, muscle strength, balance).

• Journal of Korean Society of Steel Construction
• /
• v.16 no.3 s.70
• /
• pp.377-385
• /
• 2004

An experimental and analytical study on the behavior of the wall-support joint in SC(steel plate-concrete) structure was performed. Nine full-scale specimens were tested with a horizontal monotonic load, all acting in the same plane, causing a uni-axial moment on the SC structure's wall-support beam joint. The main focus is to examine thenonlinear behavior and ultimate strength of the SC wall-support joint. The effects of parameters, such aslocation of support, thickness of the steel plate, and size of support, were studied. The yield strength and ultimate strength of the plate-concrete wall was defined by examining the load-deflection relationship, showing the tension membrane action.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• v.y2004m10
• /
• pp.1-6
• /
• 2004

We ensure a flat and regular basic surface by using part of joint waterproofing improved sheet method applying the upper slab of a concrete structure. We solve the problem of getting loose scale the general sheet by waterproofing of the sheet and improving adhesive strength of the basic concrete. Also, waterproofing sheet union to problem of joint have solved using of insertion type method so that, it improved a watertightness. It has improved in resist impact, resist abrasion and it is the effect of shortened construction period and cutting down on construction expenses. Here are the special quality and superiority of this waterproofing research. (1) Level material has the super adhesive strength so that it makes the basic surface without the gab of waterproofing sheet and waterproofing layer with the string adhesive strength. (2) We unite the sheet with the joining part between sheets by waterproofing sheet joint using of method. (3) There is the effect of shortened construction period and cutting down on construction expenses without waterproofing of protection.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.20 no.2
• /
• pp.51-59
• /
• 1983

The versatile practical use of electron beam welding which is very high energy density is still in early stage, but in the special welding field, the welding process is used in manufactured goods. The investigation for electron beam welding up to the present was almost achieved not for the mechanical properties of welded joint but for the process itself. On this investigation, the fatigue strength, crack propergation phenomena and hardness of weld metal and heat affected zone of partially penetrated welded joint of HT80 steel by electron beam welding was accomplished. The tensile fatigue strength in weld line direction of the joint was about $25kg/mm^2$. There still appeared spikes on the tips of penetration, and the crack initiated at the tips of spikes not from the roots. The hardness of the weld metal was higher than it of base metal because of production of martensite by rapid cooling.

• Structural Engineering and Mechanics
• /
• v.76 no.3
• /
• pp.337-354
• /
• 2020

Reinforced concrete beam-column (RCBC) joints of laterally loaded unbraced frames are sometimes controlled by their shear behavior. This behavior relies on multiple and interdependent complex mechanisms. There are already several studies on the influence of some parameters on the shear strength of reinforced concrete joints. However, there are no studies methodically tackling all the most relevant parameters and quantifying their influence on the overall joint behavior, not just on its shear strength. Hence, considering the prohibitive cost of a comprehensive parametric experimental investigation, a nonlinear finite element analysis (NLFEA) was undertaken to identify the key factors affecting the shear behavior of such joints and quantify their influence. The paper presents and discusses the models employed in this NLFEA and the procedure used to deduce the joint behavior from the NLFEA results. Three alternative, or complementary, quantities related to shear are considered when comparing results, namely, the maximum shear stress supported by the joint, the secant shear stiffness at maximum shear stress and the secant shear stiffness in service conditions. Depending on which of these is considered, the lower or higher the relevance of each of the six parameters investigated: transverse reinforcement in the joint, intermediate longitudinal bars and diagonal bars in the column, concrete strength, column axial load and confining elements in transverse direction.

• Composites Research
• /
• v.24 no.4
• /
• pp.48-54
• /
• 2011

The effect of moisture contents by salt water on the strength of composite single-lap bonded joints is investigated. The specimens were manufactured in an autoclave by secondary bonding and immersed in the 3.5% salt water of $71^{\circ}C$ for different durations to get various moisture contents; 0, 0.2, 0.5, 1.0, and 2.0%(saturation). A total of 80 joint specimens were tested for 5 different moisture contents and 2 temperature environments. Test results show that while the joint strengths after the saturation of moisture decrease compared to those of dry ones, the strengths of the pre-saturated joint up to 1.0% of moisture content increase in both room and elevated temperature conditions. It is also shown that the strengths of joints tested in elevated temperature are slightly higher than the strength in room temperature by 2-5% until the moisture content reaches 1 %. In contrast, the high temperature strength of the saturated joint is about 5% lower than the room temperature strength.

• The Journal of Engineering Geology
• /
• v.12 no.2
• /
• pp.167-178
• /
• 2002

Properties of discontinuity for Seoul Granite in northeastern part of Seoul City were analyzed by dividing structural domains into Surak and Bulam Mtn. areas. Important parameters measured among several engineering properties of a rock during tunnel excavation and road construction are as follows: 1) Orientation of joint, 2) joint spacing, 3) joint density, and 4) uniaxial compressive strength. Orientation, spacing, and density of joints can be directly measured during field investigation using scanline survey, circle-inventory method, and window survey. Uniaxial compressive strength of the rock was calculated by a simple correlation equation although it is originally necessary to prepare core samples in measuring it. Major orientations of joints measured from both areas are 3 sets of joints with different orientations. In other words, they are 2 sets of orthogonal joint and 1 set of sheet joint that is dipping at low angle, and have very similar orientations in both areas. Joint densities in both areas range from 0.039 and 0.066/cm, and average joint length are between 1.30 and 4.52m. Average joint spacing also has values from 10.3cm up to 59.6cm, and shows significant difference along specific orientation of scanlines measured. Values of uniaxial compressive strength calculated on the basis of Schmidt hammer rebound values range from 217 to 335 MPa, which indicates very strong rock type by classification of wall strength.

• Korean Journal of Applied Biomechanics
• /
• v.25 no.4
• /
• pp.401-412
• /
• 2015

Objective : The purpose of this study is to evaluate the effects of hip joint exercises and orthotics on RCSP, ankle's range of motion, and core muscle strength of middle school students with pes planus. Method : Out of the original pool of 200 students, 60 students with pes planus (RCSP < -2) were selected for the study. The selected 60 students were then divided into four groups. The first group was a combined orthotics and exercise group (12 students), the second was the orthotics-only group (9 students), the third was the exercise-only group (8 students), and the last was the control group (10 students). Exercise groups worked out twice a week for 60 minutes per session over 8 weeks. The independent variables were corrective hip joint exercises and orthotics. The dependant variables consisted of kinematic and kinetic variables. The kinematic variables were RCSP, and ankle's range of motion (dorsiflexion and plantarflexion). The kinetic variables were muscles forces that consist in core muscle strength, which are hip joint adduction, abduction, and flexion muscles forces. Statistical analysis was performed via SPSS 18.0 with multivariate analysis of covariance (MANCOVA) and a paired t-test was used. Results : The left foot was more responsive to the treatments, both exercise and orthotics, than the right foot. RCSP improved significantly in the left foot for the first and third groups. Only the first group significantly improved hip joint adduction, abduction, and flexion muscles' strengths. As for the ankle's range of motion of the left foot, plantarflexion showed improvement when treated with exercise, orthotics, or both. Conclusion : This study found that exercise is more effective in correcting RCSP and foot orthotics is more effective in reinforcing core muscle strength. Future studies should expand on these results to examine the relationship between the ankle, hip, and pelvis.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.8 no.2
• /
• pp.183-196
• /
• 2006

Rock joint roughness obtained from the camera-type 3D scanner was classified into waviness and unevenness. The classification criteria were established in the previous study; digital filtering was used to distinguish one from another. The classified and original profiles were used to produce metal moulds. For accurate machining of the moulds, the WEDM(Wire-cut Electric Discharge Machining) was adopted. Specimens were cast using high strength gypsum, and joint shear tests were performed by varying normal stress from low value to high one. Roughness mobilization characteristics depending on the asperity scale and the applied normal stress were investigated. A new equation was proposed to predict shear strength of rock joint, which can consider the characteristics of roughness mobilization and roughness parameters. The roughness quantification composed of waviness and unevenness was found to be a useful method to predict the joint shear strength.