Properties of Disconitinuity for the Seoul Granite in the Northeastern Part of Seoul City

서울시 북동부의 서울화강암에 대한 불연속면의 특성

  • 정상원 (충북대학교 과학교육학부) ;
  • 정상용 (부경대학교 환경지질과학과)
  • Published : 2002.06.01

Abstract

Properties of discontinuity for Seoul Granite in northeastern part of Seoul City were analyzed by dividing structural domains into Surak and Bulam Mtn. areas. Important parameters measured among several engineering properties of a rock during tunnel excavation and road construction are as follows: 1) Orientation of joint, 2) joint spacing, 3) joint density, and 4) uniaxial compressive strength. Orientation, spacing, and density of joints can be directly measured during field investigation using scanline survey, circle-inventory method, and window survey. Uniaxial compressive strength of the rock was calculated by a simple correlation equation although it is originally necessary to prepare core samples in measuring it. Major orientations of joints measured from both areas are 3 sets of joints with different orientations. In other words, they are 2 sets of orthogonal joint and 1 set of sheet joint that is dipping at low angle, and have very similar orientations in both areas. Joint densities in both areas range from 0.039 and 0.066/cm, and average joint length are between 1.30 and 4.52m. Average joint spacing also has values from 10.3cm up to 59.6cm, and shows significant difference along specific orientation of scanlines measured. Values of uniaxial compressive strength calculated on the basis of Schmidt hammer rebound values range from 217 to 335 MPa, which indicates very strong rock type by classification of wall strength.

서울시 북동부의 서울화강암에 대한 불연속면의 특성을 수락산과 불암산 지역으로 구분하여 비교, 분석하였다. 본 연구에서는 암석의 공학적 특성 중 터널과 도로 건설시 중요하게 취급하여 측정된 요소는 다음과 같다: 1) 절리의 방향성, 2) 절리간격, 3) 절리밀도, 4) 암석의 일축압축강도. 이 중 절리의 방향성, 절리간격과 절리밀도는 선조사법, 원형조사법, 그리고 면적조사법을 이용하여 야외에서 직접 측정될 수 있는 요소이나, 암석의 일축압축강도의 측정에는 원래 암석의 시추코아 표본이 필요하지만 이번 연구에서는 간단히 응용할 수 있는 대비공식을 이용하여 계산하였다. 측정된 대표적인 절리의 방향성은 두 지역에서 모두 3조의 방향성이 나타났다. 즉 2조의 수직정방절리와 저각으로 경사하는 1조의 판상절리이었으며, 서로 매우 유사한 방향성을 갖는다. 측정된 절리밀도는 0.039-0.066/cm 이었으며, 면적조사법으로 측정된 평균절리길이는 1.30-4.52m, 평균절리간격은 10.3cm에서 최대 59,6cm로 측정된 조사선의 방향에 따라 변화가 심하다. 또한 슈미트해머 타격값에 근거한 절리면의 일축압축강도는 217 MPa에서 335 MPa로 강한 암체로 판명되었다.

Keywords

References

  1. 한국의 지질 대한지질학회
  2. 서울-남천점 지질도폭 설명서(1:250,000) 이병주;김유봉;이승렬;김정찬;강필종;최현일;진명식
  3. 서울외곽순환(일산-퇴계원) 고속도로 북한산 국립공원 터널통과에 의한 수리변동분석 보고서 서울고속도로(주)
  4. 토질조사보고서 한국도로공사
  5. 한국지질도(1:1,000,000) 한국자원연구소
  6. 한국지질도(1:5,000) 홍승천;이병주;황상기
  7. Lecture note of Dr. Wattres in University of Nevada, Reno Aufmuth
  8. Exploration for rock engineering v.1 Rock mass classifications in rock engineering Bieniawski, Z. T.
  9. Rock mechanics for underground mining, (2nd edition) Brady, B. H. G.;Brown, E. T.
  10. Journal of Korean Earth Science Society v.19 The determination of Rock Mass Rating(RMR) with joint spacing and its relation to slope stability Cheong, S.;Lee, C. Z.
  11. Structural geology of rocks and religions, (2nd edition) Davis, G. H.;Reynolds, S. J.
  12. Engineering classification and index properties for intact rocks Air Force Weapons Laboratory;Research and Technology Division;Air Force Systems Command ;Kirkland Air Force Base;New Mexico; Deere, D. V.;Miller R. P.
  13. Rock characterization for testing and monitoring ISRM;E. T. Brown(ed.)
  14. Int. Jour. Rock Mech. and Mining Sciences and Geomechanics Abstracts v.18 Estimating the mean length of discontinuity traces Ralph, P. J. https://doi.org/10.1016/0148-9062(81)90976-1
  15. Proceeding of the Institution of Civil Engineers v.61 Ground movement caused by tunnelling in chalk Priest, S. D. https://doi.org/10.1680/iicep.1976.3501
  16. Discontinuity Analysis for Rock Engineering Priest, S. D.
  17. Int. J. Rock Mech. Min. Sci. v.18 Estimation of discontinuity spacing and trace length using scanline surveys Priest, S. D.;Hudson, J. A. https://doi.org/10.1016/0148-9062(81)90973-6
  18. Engineering classification and index properties for intact rocks Deere, D. V.;Miller R. P.