• Journal of Welding and Joining
• /
• 제25권2호
• /
• pp.55-61
• /
• 2007

Flash butt weldability of 590MPa dual phase steel is carried out under micro metallographical examination and macro mechanical property tests. The objective of present study is to investigate the cause that brings on bond line fracture, and is to improve mechanical properties of the flash butt welded joint. The joint of flash butt welding has a superior tensile property, but has bad formability due to oxide formed at bond interface. The HAZ softening in the weld joint does not show. It was found that mechanical properties were increased with optimizing welding parameters and making application of oil dripping and post-weld heat treatment.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 제14회 신호처리 합동 학술대회 논문집
• /
• pp.85-88
• /
• 2001

In this paper we consider a problem of blind co-channel signal separation, the goal of which is to estimate multiple co-channel digitally modulated signals using an antenna array. We employ the joint maximum likelihood estimation and present a sequential algorithm, which is referred to as sequential joint maximum likelihood (SJML) algorithm. It separates multiple co-channel signal on-line and converges fast in overdetermined noisy communication environment. And the computational complexity of SJML for M-QAM (M=8, 16, 64,...) signals is less expensive compared to the SLSP. Useful behavior of this algorithm are confirmed by simulations.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.135-138
• /
• 2009

Quality evaluation of laser welded MCFC separator panels with large active area was performed. Lap joint was applied to produce stable air-tight seam weld by employing Nd:YAG laser. Results showed that surface contamination played a key role to form weld defects at the joint interface. However, there was no evidence that weld width at the lap joint changed after the stack operation time of 2,890h. Test results also revealed that the reinforcement values which were measured on the weld line after long time operation, were stable.

• 생명과학회지
• /
• 제20권11호
• /
• pp.1704-1710
• /
• 2010

본 연구는 뇌졸중 발병 후 재활운동에 참가하는 환자들을 대상으로 재활운동 3개월이 지난 시점에서 1차 실험을 하였고, 6개월이 지난 시점에서 2차 실험을 하여 운동역학적 비교분석을 하였다. 실험에 사용된 장비는 영상분석기, 족저압분석기, 근전도분석기를 사용하였다. 대상자는 7명으로 하였으며 통계방법은 t-test분석 이용하였다. 결과는 엉덩관절의 최대신전 피크 값과 최대신전 피크 모멘트 값에서 통계적으로 유의한 차이를 나타내었다(p<0.05). 족저압의 비교에서는 환측 다리의 족저압에서 일반적인 걷기 동작시에 족저압의 중심이동거리에서 통계적으로 유의한 차이를 나타내었다(p<0.05). 근전도 분석에서는 대퇴사두근 중의 대퇴직근과 외측광근의 근력에서 통계적으로 유의한 차이를 나타내었다(p<0.05).

• Communications for Statistical Applications and Methods
• /
• 제20권3호
• /
• pp.169-174
• /
• 2013

The ROC curve is drawn with two conditional cumulative distribution functions (or survival functions) of the univariate random variable. In this work, we consider joint cumulative distribution functions of k random variables, and suggest a ROC curve for multivariate random variables. With regard to the values on the line, which passes through two mean vectors of dichotomous states, a joint cumulative distribution function can be regarded as a function of the univariate variable. After this function is modified to satisfy the properties of the cumulative distribution function, a ROC curve might be derived; moreover, some illustrative examples are demonstrated.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.40-43
• /
• 1996

An off-line programming, OLP, system is widely used in automation fines. To help an on-line robot system to carry out desirable tasks planned by the off-line simulation, an approach to the real-time communication is presented. The OLP system developed consists of a software, a host computer(PC), a SCARA robot body, four servo drivers, and four independent joint controllers. This study focuses on the software where real-time communication is included. The software, can be used in teaching, trajectory planning, real-time running, and performance evaluation. The evaluation of different control algorithms is one of the merits of the software. The software can give servo commands for task running. A comparison of generated and corresponding actual trajectories provides the evaluation of task performance. The safety, of the OLP system is ensured by alarming malfuntions of the system. The OLP system developed can reduce the teaching time and increase the user's convenience.

• Steel and Composite Structures
• /
• 제21권2호
• /
• pp.443-460
• /
• 2016

In this paper, the efficiency and effectiveness of two strengthening methods for upgrading behavior of the two external weak reinforced concrete (RC) beam-column joints were experimentally investigated under cyclic loading. Since two deficient external RC joints with reduced beam height and low strength concrete were strengthened using one-way steel prop and curbs with and without steel revival sheets on the beam. The cyclic performance of these strengthened specimens were compared with two another control external RC beam-column joints, one the standard RC joint that had not two mentioned deficiencies and another had both. Therefore, four half-scale RC joints were tested under cyclic loading.The experimental results showed that these innovative strengthening methods (RC joint with revival sheet specially) surmounted the deficiencies of weak RC joints and upgraded their performance and bearing capacity, stiffness degradation, energy absorption, up to those of standard RC joint. Also, results exhibited that the prop at joint acted as a fuse element due to adding steel revival sheets on the RC beam and showed better behavior than that of the specimen without steel revival sheets. In other words by stiffening of beam, the prop collected all damages due to cyclic loading at itself and acted as the first line of defense and prevented from sever damages at RC joint.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.535-536
• /
• 2011

This paper studies the validity about a joint operation of neutral wire and overhead grounding wire in combined distribution systems. The overhead grounding wire and neutral wire are currently installed separately and grounded by common. However there is no any ineffectiveness or electrical problem in case of the proposed system, such system can be operated at real distribution system. Therefore this paper describes the suitability of a joint operation through lightning surge analysis on combined distribution systems and analyzes the optimal position of lightning arrester on joint operation of neutral wire and overhead grounding wire. Lightning surge analysis is carried out by EMTP/ATPDraw to obtain the overvoltage of overhead line and underground cable in various conditions such as location and current types of lightning stroke. Over voltage gained by the analysis show that the insulation strength of the joint operation case is not stable compare with the current operation case.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.399-402
• /
• 2006

The outer race of CV(constant velocity) joint is an important load-supporting automotive part, which transmits torque between the transmission gear box and driving wheel. The outer race is difficult to forge because its shape is very complicated and the required dimensional tolerances are very small. Traditional warm and cold forging methods have their own limitations to produce such a complex shaped part; warm forging requires complex system with relatively higher manufacturing cost, while cold forging is not applicable to materials with limited formability. Therefore, multistage forging may be advantageous to produce complex shaped parts. In order to build a multistage forging system, it is necessary to characterize mechanical properties in response to system design parameters such as temperature, forging speed and reduction. For the analysis of formability of multistage forging process, finite element method(FEM) has been used for the process analysis. As a model case, a constant velocity (CV) joint forging process is analyzed by FEM, since CV joint has a complex shape and also its required dimensional tolerances are very tight. The data acquired by FEM is compared with operational forging data obtained from an industrial production line. Based on this comparative analysis, multistage forging process for CV joints is proposed.

• 대한정형도수물리치료학회지
• /
• 제22권1호
• /
• pp.71-76
• /
• 2016

Background: The objective of this research is to provide base line data on Korea Baseball rehabilitation treatment by presenting the distribution of upper extremity surgeries according the surgical sites of Korean professional baseball players. Methods: The targets of this research are 561 players from nine Korean baseball clubs. The number of players that have undergone surgery was investigated. In other words, the frequency of shoulder joint surgeries, elbow joint surgeries, and wrist and hand surgeries per each baseball club was investigated. Results: The number of the players who have had surgeries was 151, but among the players, there were some who have had repeated surgeries for which the total number of surgery experience was 162. The result showed that elbow joint surgeries were the most frequently enacted, followed by shoulder joint surgeries, and wrist and hand surgeries. From the nine clubs, Samsung was the club with the highest frequency of surgeries. Conclusions: This research shows that Korean professional baseball players need special training centers with systematic rehabilitation programs. Another conclusion suggests that urgent need for rehabilitation program of upper arm which particularly focused on elbow joint is existing. On the basis of this research, we expect more studies on the specific rehabilitation programs which is categorized by injury areas.