• Journal of Welding and Joining
• /
• v.31 no.6
• /
• pp.8-16
• /
• 2013

As the energy consumption increases rapidly, power generation needs the high energy efficiency continuously. To achieve the high efficiency of power generation, the materials used have to endure the higher temperature and pressure. The 9-12%Cr steels possess good mechanical properties, corrosion resistance, and creep strength in high temperature due to high Cr contents. Therefore, the 9-12%Cr steels are widely used for the high-temperature components in power plants. Even though the steels usually have a fully martensitic microstructure, they are susceptible to the formation of ${\delta}$-ferrite specifically during the welding process. The formation of ${\delta}$-ferrite has several detrimental effects on creep, ductility and toughness. Therefore, it is necessary to avoid its formation. As the volume fraction of ${\delta}$-ferrite is less than 2% in microstructure, it has the isolated island morphology and causes no significant degradation on mechanical properties. For ${\delta}$-ferrite above 2%, it has a polygonal shape affecting the detrimental influence on the mechanical properties. The formation of ${\delta}$-ferrite is affected by two factors: a chemical composition and a welding heat input. The most effective ways to get a fully martensite microstructure are to reduce the chromium equivalent less than 13.5, to keep the difference between the chromium and nickel equivalent less than 8, and to reduce the welding heat input.

• Journal of Welding and Joining
• /
• v.30 no.6
• /
• pp.49-55
• /
• 2012

The tandem welding process is one of the most efficient welding processes widely used in material joining technique such as manufacturing of strong and durable structures. It facilitates high rate of joint filling with little increase in the overall rate of heat input due to the simultaneous deposition from two electrode wires. The two electrodes in tandem welding process helps in high-efficiency and high productive of welding process. In this study a automated tandem welding system is developed to determine the correlation between cathode and anode and compared with current ratio of the two electrode torch. Three different inter-electrode distances were chosen, 25mm, 35mm and 45mm to perform the experiment with three different current ratio. From the experiment results, the current ratio between two torch has a large impact on width, height and depth of penetration. In addition, a stable bead geometry is obtained when inter-electrode distance is 35mm.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.229-231
• /
• 2005

Friction surfacing of STS304 consumable rod on S45C substrate was investigated by microstructural observation and mechanical tests. STS304 layer formed a strongly-bonded thick layer under a wide range of surfacing conditions. The hardness distribution showed the peak value in the boundry layer, while the highest coating efficiency obtained in the condition of 1000rpm-2.5mm/sec-2.5mm/sec. As the consumable rotation rate and the traveling rate increased, the coating efficiency tended to decrease. On the other hand, as the feeding rate increased, the coating efficiency appeared to be increased.

• Journal of Welding and Joining
• /
• v.23 no.1
• /
• pp.55-60
• /
• 2005

A three-dimensional Gaussian heat source model is modified to include the effects of the gap and thickness-difference for the laser keyhole welding. The gap of the butt joint influences the welding efficiency such that the melting area decreases linearly with the gap. When the different plate thickness is used such as the tailored blank welding, melting areas of the thick and thin plates are predicted by introducing the thickness-difference factor. The calculated results using the modified heat source show reasonably good agreements with the experimental results.

• International Journal of Automotive Technology
• /
• v.7 no.5
• /
• pp.565-570
• /
• 2006

The development of a light-weight vehicle is in great demand for enhancement of fule efficiency and dynamic performance. The vehicle weight can be reduced effectively by using lightweight materials such as aluminum and magnesium. However, if such materials are used in vehicles, there are often instances when different materials such as aluminum and steel need to be joined to each other. The conventional joining method, namely resistance spot welding, cannot be used in joining different materials. Self-piercing rivet(SPR) and adhesive bonding, however, are good alternatives to resistance spot welding. This paper is concerned with the crushing test of double hat-shaped member made by resistance spot welding, SPR and adhesive bonding. Various parameters of crashworthiness are analyzed and evaluated. Based on these results, the applicability of SPR and adhesive bonding are proposed as an alternative to resistance spot welding.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.606-611
• /
• 2002

Welding using lasers can be mass-produced in high speed. In the laser welding, performing real-time monitoring system of the welding quality is very important in enhancing the efficiency of welding. In this study, the plasma and molten metal which are generated during laser welding were measured using the UV sensor and IR sensors. The results of laser welding were classified into five categories such as optimal heat input, little low heat input, low heat input, partial joining due to gap mismatch, and nozzle deviation. Also, a system was formulated which uses the measured signals with a fuzzy pattern recognition method which is used to perform real-time evaluation of the welding quality and the defects which can occur in laser welding.

• Journal of Welding and Joining
• /
• v.19 no.5
• /
• pp.506-511
• /
• 2001

Weld overlay has been developed to improve the property of material surface which is used in the severe environment. Weld overlay is the process which uses an arc heat and welds different composition of alloy on the substrate for the improvements of heat resistance and wear resistance. Weld overlay has a lot of advantages which are high hardness, good processing efficiency, easy controlling of layer thickness, good quality and low cost. In this study, weld overlay was performed by MAG welding on the base metal(SS400) with filler metal which contain composite powders(Cr+C+Mn+Mo+NbC) and solid wire(JIS-YGW11). Characterization of hardness and wear resistance were analyzed by EDS, EPMA, XRD and observations of microstructure were performed to investigate characteristics of overlays. The experimental results of overlaid specimens manufactured with Cr+C+Mn+Mo+NbC powders were obtained as fellows. ${\alpha}-phase$, M(Fe, Cr)3C and NbC of overlays were increased with decreasing the wire feed rates and increasing powder feed rates. Also the hardness of overlays were increased and the specific wear were decreased.

• Journal of Welding and Joining
• /
• v.16 no.5
• /
• pp.48-55
• /
• 1998

This study was undertaken to investigate the friction welding of A2024-T6 aluminum alloy and SM45C carbon steel using insert metals. The relationships among the friction welding conditions, the tensile strength of joints, the hardness distribution of welds, the microstructure of welds and the tensile fracture surfaces were mainly investigated through this experiment. When the A6063-T5 aluminum alloy of insert metal was used, the maximum tensile strengh of joint was obtained. In this case, the maximum joint efficiency was 75.3 percent and in the case of unusing the insert metals, it was 37.7 percent. Optimal welding conditions were N=2000rpm, P$_1$=40MPa, P$_2$=140MPa, t$_1$=1.0sec and t$_2$=5sec.

• Journal of Welding and Joining
• /
• v.33 no.6
• /
• pp.36-41
• /
• 2015

In the automotive industry, TWB hot stamping process is broadly adapted to reduce weight of the car and improve fuel efficiency. However, the process faces a problem of weakened strength of the welded zone after hot stamping process, due to the fact that Al-Si elements of the coating layer penetrating the welded zone. In this study, filler wires with high percentages of carbon and manganese is adapted during laser welding process to secure the strength of the fusion zone. In addition, wire feeding speed and laser welding speed are optimized by sample test.

• Journal of Welding and Joining
• /
• v.20 no.4
• /
• pp.534-537
• /
• 2002

In the various industry such as shipbuilding and automobile, etc., Al-alloys are used to reduce weight and improve economical efficiency, and they are mainly utilized in the process of Friction Stir Welding (FSW). A number of studies have been carried out on the metallurgical characteristics of friction stir welding In Al-alloys. However, research on the thermal behavior of FSW by using numerical analysis is not sufficient in the domestic and abroad. In this paper, therefore, numerical simulation was used to find out thermal behaviour of FSW by finite element method. We considered heat source that occurred by friction between tool shoulder including pin and base metal. To confirm the result of simulation, macrostructure is examined and compared after welding. The result of numerical simulation shows that Al-alloy is welded under a melting point of Al around pin by FSW.