• 센서학회지
• /
• 제26권1호
• /
• pp.56-59
• /
• 2017

This paper presents the Inkjet-printed strain gauge using PEDOT:PSS. The strain gauge (width 0.6 mm, length 20 mm, thickness $0.3{\mu}m$) was printed on the PET film using PEDOT:PSS ink. The resistance variation of the fabricated strain gauge was measured by the digital multi-meter with the displacement range of -4 to 10 mm. As the measured result, resistance variation (${\Delta}R/R_0$) has approximately 0.75%, linearity of 99.87%. The fabricated strain gauge is expected to the various applications such as tape type pressure sensor, PMS(pressure mapping sensor), wearable devices.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.215-219
• /
• 2004

We reported two new techniques of barrier rib formation that are applicable to a variety of structures for high-efficiency PDPs suitable for mass-production [1]. These two methods are mold replication and direct glass sculpting. Especial progress has since been made in improving these methods to be more suitable for high-efficiency PDPs with the DelTA cell structure. This paper reports photolithographic fabrication methods for the masters used in mold replication. The masters for more complex barrier rib forms are easier to make with these methods. The paper also reports a process that combines the direct glass sculpting method with an ink-jet printing method of electrode formation.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권2호
• /
• pp.1771-1773
• /
• 2007

Surface modification of the gate dielectric has a strong influence on the performance of printed transistors. The surface modification occurs between the gate dielectric and semiconductor. The printed transistor with evaporated vanadium pentoxide ($V_2O_5$) modification exhibits a mobility of $0.2cm^2\;V^{-1}\;s{-1}$ and a subthreshold slope of 1.47 V/decade.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.2509-2512
• /
• 2005

In this paper, a position control scheme of the ink droplet is presented for the high image quality and print speed inkjet printer. The proposed scheme estimates the impact position and compensates it by control of the fire strobe time based on the dynamic equations describing the moving trajectory of the ink droplet. Compared to the conventional fire strobe control which is based on the simple synchronization the fire strobe with the position signal of the inkjet nozzle, the proposed control scheme provides more accurate impact position control during the carrier is moving with accelerated or decelerated speed as well as constant speed. The availability of printing during the acceleration and deceleration states of the carrier moving enables the print speed up and the frame size down which means the cost down.

• 한국가시화정보학회지
• /
• 제9권2호
• /
• pp.48-53
• /
• 2011

The shape of nozzle cross-section plays an important role in stabilizing electrospray jet. The angle of contact line is governed based on the famous Young-Laplace equation. Compared to a round nozzle that has a constant curvature along the orifice, the square nozzle has four square corner edges and four straight edges that hold the meniscus in a different manner and is of interest in this study. By utilizing both square and round capillary nozzle, we examine the effect of nozzle shape in electrohydrodynamic jetting. The ejections were recorded with a high speed camera and analyzed to examine the jetting repeatability based on dynamic movement of meniscus. The result suggests that if the corner edges are not sharp, then its effect on repeatability is also limited.

• Journal of Welding and Joining
• /
• 제29권5호
• /
• pp.90-94
• /
• 2011

Ag metallic particles from nano-scale to submicron-scale are combined with organic solvent to provide fine circuits and interconnection. Ink-jet printing with Ag nano particle inks demonstrated the potentials of the new printed electronics technology. The bonding at the interface between the Ag wiring layer and the various substrates is very important. In this study, the details of interfaces in Ag wiring are investigated primarily by microstructure observation. By adjusting the materials and sintering conditions, nicely formed interfaces between Ag wiring and Cu, Au or organic substrates are achieved. In contrast, transmission electron microscope (TEM) image clearly shows interface debonding between Ag wiring and Sn substrate. Sn oxides are formed on the surface of the Sn plating. The formation of these is a root cause of the interface debonding.

• 한국의학물리학회지:의학물리
• /
• 제28권3호
• /
• pp.100-105
• /
• 2017

The purpose of the present study was to develop and evaluate patient-customized helmets with a three-dimensional (3D) printer for radiation therapy of malignant scalp tumors. Computed tomography was performed in a case an Alderson RANDO phantom without bolus (Non_Bolus), in a case with a dental wax bolus on the scalp (Wax_Bolus), and in a case with a patient-customized helmet fabricated using a 3D printer (3D Printing_Bolus); treatment plans for each of the 3 cases were compared. When wax bolus was used to fabricate a bolus, a drier was used to apply heat to the bolus to make the helmet. $3-matic^{(R)}$ (Materialise) was used for modeling and polyamide 12 (PA-12) was used as a material, 3D Printing bolus was fabricated using a HP JET Fusion 3D 4200. The average Hounsfield Unit (HU) for the Wax_Bolus was -100, and that of the 3D Printing_Bolus was -10. The average radiation doses to the normal brain with the Non_Bolus, Wax_Bolus, and 3D Printing_Bolus methods were 36.3%, 40.2%, and 36.9%, and the minimum radiation dose were 0.9%, 1.6%, 1.4%, respectively. The organs at risk dose were not significantly difference. However, the 95% radiation doses into the planning target volume (PTV) were 61.85%, 94.53%, and 97.82%, and the minimum doses were 0%, 77.1%, and 82.8%, respectively. The technique used to fabricate patient-customized helmets with a 3D printer for radiation therapy of malignant scalp tumors is highly useful, and is expected to accurately deliver doses by reducing the air gap between the patient and bolus.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.154-154
• /
• 2006

글씨 전도성 잉크의 인쇄공정에 있어서 반복인쇄를 정밀하게 수행할 수 있는 기술로서 align system을 개발하였다. 이 system의 resolution 은 0.5um 이며 인쇄 working plate의 이송속도는 최대 1.5m/s 이다. 현재 소성 공정을 포함한 반복인쇄 실험은 30um이상의 drop탄착점 오차를 보이고 있으며, 두께와 전기전도도 향상을 위한 정밀한 align system이 필요하게 되었다. 이를 충족시키기 위해 개발되어진 초정밀 align system은 $1{\sim}2{\mu}m$이내의 오차로 반복인쇄가 가능하며, head가 토출하는 잉크의 straightness 및 전도성 잉크를 토출하는 인쇄평가기의 기계적 정밀도도 확인할 수 있다. 모든 잉크 배선의 두께 항상 인쇄실험이 가능하며, substrate의 종류와 잉크에 제한적이지 않다. 특히 prototype의 기판배선을 위해 PCB에 배선을 형성할 시에 본 system으로 직접 align mark를 지정할 수 있어 기판 내에 미리 제작되어진 align용 인식마크가 불필요하다. 이 system을 이용하여 drop과 배선의 반복인쇄실험을 진행하였으며, 광학현미경과 3D profiler를 사용하여 분석해 보았다.

• 한국의학물리학회지:의학물리
• /
• 제32권4호
• /
• pp.99-106
• /
• 2021

Purpose: In this study, we aimed to manufacture a patient-specific gel phantom combining three-dimensional (3D) printing and polymer gel and evaluate the radiation dose and dose profile using gel dosimetry. Methods: The patient-specific head phantom was manufactured based on the patient's computed tomography (CT) scan data to create an anatomically replicated phantom; this was then produced using a ColorJet 3D printer. A 3D polymer gel dosimeter called RTgel-100 is contained inside the 3D printing head phantom, and irradiation was performed using a 6 MV LINAC (Varian Clinac) X-ray beam, a linear accelerator for treatment. The irradiated phantom was scanned using magnetic resonance imaging (Siemens) with a magnetic field of 3 Tesla (3T) of the Korea Institute of Nuclear Medicine, and then compared the irradiated head phantom with the dose calculated by the patient's treatment planning system (TPS). Results: The comparison between the Hounsfield unit (HU) values of the CT image of the patient and those of the phantom revealed that they were almost similar. The electron density value of the patient's bone and brain was 996±167 HU and 58±15 HU, respectively, and that of the head phantom bone and brain material was 986±25 HU and 45±17 HU, respectively. The comparison of the data of TPS and 3D gel revealed that the difference in gamma index was 2%/2 mm and the passing rate was within 95%. Conclusions: 3D printing allows us to manufacture variable density phantoms for patient-specific dosimetric quality assurance (DQA), develop a customized body phantom of the patient in the future, and perform a patient-specific dosimetry with film, ion chamber, gel, and so on.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.421-427
• /
• 2009

We successfully fabricated 4.7-inch organic thin film transistors array with $640{\times}480$ pixels on flexible substrate. All the processes were done by photolithography, spin coating and ink-jet printing. The OTFT-Electrophoretic (EP) pixel structure, based on a top gate OTFT, was fabricated. The mobility, ON/OFF ratio, subthreshold swing and threshold voltage of OTFT on flexible substrate are: 0.01 ^2/V-s, 1.3 V/dec, 10E5 and -3.5 V. After laminated the EP media on OTFT array, a panel of 4.7-inch $640{\times}480$ OTFT-EPD was fabricated. All of process temperature in OTFT-EPD is lower than $150^{\circ}C$. The pixel size in our panel is $150{\mu}m{\times}150{\mu}m$, and the aperture ratio is 50 %. The OTFT channel length and width is 20 um and 200um, respectively. We also used OTFT to drive EP media successfully. The operation voltages that are used on the gate bias are -30 V during the row data selection and the gate bias are 0 V during the row data hold time. The data voltages that are used on the source bias are -20 V, 0 V, and 20 V during display media operation.