• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.6
• /
• pp.596-605
• /
• 2007

The behavior of a non-buoyant turbulent round jet discharging horizontally was investigated experimentally. The instantaneous velocity field of the jet was obtained using the particle image velocimetry (PIV) method and used to calculate the mean velocity field by phase-averaging. This study tested regular waves with a relatively small wave height for a wavy environmental flow. The centerline and cross-sectional velocity profiles were reported to demonstrate the effect of the waves on the jet diffusion in respect of wave height and wave phase. The wave phase effect was studied for three phases: zero-upcrossing point, zero-downcrossing point, trough. From the results, it is found that the centerline velocity decreases and width of the cross-sectional profile increases as the wave height increases. In addition, the self-similarity of the cross-sectional profile appears to break down although the width of each case along the axial distance does not vary significantly. The phase effect is found to be relatively small compared to the wave height effect.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.4
• /
• pp.1395-1405
• /
• 1996

The purpose of this experimental research is to investigate the local heat transfer characteristics in the upward free water jet impinged on a downward flat plate of uniform heat flux. The inner shape of rectangular nozzle used was sine curve type and its contraction ratio of inlet to outlet area was five. Experimental parameters considered were Reynolds number, nozzle exit-flat plate distance, and level of supplementary water. Local Nusselt number was influenced by Reynolds number, Prandtl number, supplementary water level, and distance between the nozzle exit and flat plate. Within the impingement region, the Nusselt number has a maximum value on the nozzle center axis and decreases monotonically outward from center. Outside of the impingement region, on the other hand, the Nusselt number has a secondary peak near the position where the distance from nozzle center reaches four times the nozzle width. However if nozzle exit velocity exceeds 6.2 m/s, the secondary peak appears also in the impingement region. The empirical equation for the stagnation heat transfer is a function of Prandtl, Reynolds, and axial distance from the nozzle exit. The optimum level of supplementary water to augment the heat transfer rate at stagnation point was found to be twice the nozzle width.

• Textile Coloration and Finishing
• /
• v.12 no.1
• /
• pp.1-11
• /
• 2000

This paper surveys the fabric weavability and machine efficiency in the various weaving looms such as Projectile, Rapiers, and Air-jet. Used projectile loom was Sulzer-PU, and FAST-R, THEMA-11E, and Picanol-GTX were used for Rapier looms, as the Air-Jet looms, Picanol PAT and OMNI types were used. Using these looms, 5 harness worsted satin fabrics were woven for surveying the fabric weavability and machine efficiency. Warp yam count of fabric is 1/40Nm, Sirofil, and filling is 1/30 Nm, worsted. End breaks of warp and filling directions for the various types of looms are measured and discussed with the mechanism of each loom. Warp and filling yam tensions are also measured and analysed with open width of shedding motion of each weaving machine. And various warp yam tensions with open width of shedding are measured and analysed according to the warp yam in various heald frame. These results fire also discussed with temples such as bar and ring. Warp yam tensions at the various positions on the fabric with various looms are measured and discussed with fabric mechanical properties such as tensile, bending, shear and surface.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.963-966
• /
• 2000

Abrasive jet machining(AJM) process is similar to the sand blasting, and effectively removes hard and brittle materials. AJM has applied to rough working such as deburring and rough finishing. As the needs for machining of ceramics, semiconductor, electronic devices and LCD are increasing, micro AJM was developed, and became the inevitable technique to micromachining. This paper describes the performance of the micro AJM in micro groove cutting of glass. Diameter of hole and width of line in this groove cutting is 80${\mu}{\textrm}{m}$. Experimental results showed good performance in micro groove cutting in glass, but the size of machined groove was increased about 2~4${\mu}{\textrm}{m}$. therefore, this micro AJM could be effectively applied to the micro machining of semiconductor, electronic devices and LCD parts.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.603-608
• /
• 2000

The characteristics of laminar and turbulent slot impinging jet flows are examined using segregated FEM with SUPG. Turbulent flows are modeled using $Wilcox^{(1)}$ $k-\;{\omega}$ turbulence model. The results are validated by comparing with velocity field of the existing experimental data. The distance of the target plate from the nozzle varies between 2, 4 and 5 times the slot jet width. Present study shows that the $k-\;{\omega}$ model gives results which agree well with the existing experimental data. In turbulence flows, the velocity profile of present calculation is more accurate than the existing numerical calculations. In laminar flows, We found tertiary vortex which was not found in the previous numerical study by M. $chen^{(6)}$ et al due to the numerical difference.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.6 no.4
• /
• pp.427-438
• /
• 1994

This experimental study was earned out to examine the heat transfer characteristics of a 2-dimensional impinging air jet on a flat plate with a set of square rods. The objectives of the study were to investigate the flow and heat transfer characteristics caused by the square rods and to find out the optimum rods arrangement. Experiment was carried out first without using the rods to establish the baseline heat transfer performance. Then, rods of different widths and clearances were installed to cause the turbulence on the fluid flow.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1450-1451
• /
• 2008

To investigate the reliability of the conductive lines patterned by ink-jet printing, we evaluated the reliability of the ink-jet printed silver (Ag) patterns according to the guide lines built up as assessments methods in the production of conventional rigid printed circuit boards. The assessment methods include the uniformity of line width and space, adhesive strength, dielectric withstand, solder float, thermal shock test and pressure cooker test (PCT). To prepare assesment vehicles, different regular test patterns were created by Ag ink-jet printing on the same polyimide substrate for each of assessment methods.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.10
• /
• pp.178-183
• /
• 2001

Abrasive jet machining(AJM) process is similar to the sand blasting and effectively removes hard and brittle materials. AJM has applied to rough working such as debarring and rough finishing. As the need for machining of ceramics, semiconductor, electronic devices and LCD are increasing, micro AJM is developed, and has become the inevitable technique to micromachining. This paper describes the performance of the micro AJM in micro grooving of glass. Diameter of hole and width of line in grooving is 80${\mu}{\textrm}{m}$. Experimental results showed good performance in micro grooving of glass, but the size of machined groove increased about 2~4${\mu}{\textrm}{m}$. With the fine tuning of masking process and compensation of film wear. this micro AJM could be effectively applied to the micro machining of semiconductor, electronic devices and LCD.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2798-2803
• /
• 2008

The confined slot air jet impinging normally on a moving flat surface has been investigated numerically by using commercial CFD code Ansys CFX-V11. Turbulent flows are modeled using k-w turbulence model. Two-dimensional turbulent flow is considered. Calculations were conducted for a nozzle-to-plate spacing of eight slot nozzle width, at three Reynolds number(Re=4500, 6700 and 10,000) and four surface-to-velocity ratios i.e. 0, 0.25, 0.5 and 1. Results are compared against corresponding cases for heat transfer from a stationary plate. Local Nusselt number is calculated under constant wall temperature condition. The analysis reveals that the average Nusselt number increases considerably with the jet exit Reynolds number, but decrease with the plate velocity.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.182-190
• /
• 1998

Behaviour of ultra-high pressure diesel spray in a constant-volume pressure chamber was studied with injection pressure ranging from 20 to 160㎫. Sprays were observed by the right angle scattering method. As a result, the spray tip penetration is first proportional to a time, and after that, it is proportional to 0.52 of the time during at the time of injection pressure and back pressure increase. An empirical correlation was made for the parameters of injection pressure, air-fuel density ratio, spray tip distance, spray angle, jet angle of spray and max. spray width.