• Journal of the Korean Wood Science and Technology
• /
• v.8 no.2
• /
• pp.6-8
• /
• 1980

Japanese larch veneer, Cryptomeria veneer and japanese cypress veneer were peeled with condition of nose bar pressure at 5%, 10%, 15%, to find the optimum nose bar pressure. 1. Optimum nose bar pressure was 15% in 2mm thickness veneer of japanese larch. 2. Optimum nose bar pressure was 5% in 2mm thickness veneer of Cryptomeria. 3. Optimum nose bar pressure was 15% in 2mm thickness veneer of japanese cypress.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.5
• /
• pp.525-534
• /
• 2017

The study aims to observe the cellular anatomical properties of Dahurian larch and Japanese larch for the species identification. In addition, other factors - the ring width, tracheid length, density, and strength - were compared and analyzed to clarify their physical and mechanical properties. To the end, three Dahurian larch trees and three Japanese larch trees by each diameter class were collected as specimens from Jeongseon-eup, Jeongseon-gun, Gangwon-do, to conduct a stem analysis. It was found that the average stand age, average diameter at breast height, and average tree height of three Dahurian larch trees and Japanese larch trees were 74 years and 51 years, 442 mm and 352 mm, and 26.1 m and 20.8 m, respectively. The cellular anatomical difference between Dahurian larch and Japanese larch can be usually found by spiral thickening, considering that it doesn't occur in Dahurian larch at all, while rarely does in the ray tracheids of Japanese larch. However, in this study, spiral thickening was not observed in the radial section of Japanese larch. The average annual growth diameters measured at 1.2 m-height of Dahurian larch and Japanese larch were 5.167 mm and 5.954 mm, respectively. Meanwhile, arboreal growth of Japanese larch was observed to be higher than that of Dahurian larch. In the physical properties test, it was measured that the latewood proportion and oven-dry density of Dahurian larch with low annual diameter growth were higher than those of Japanese larch, while the mechanical properties of Dahurian larch wood were measured 2-7% higher than those of Japanese larch wood. The data obtained from this study are expected to be used as the basic reference for species identification between Dahurian larch and Japanese larch by DNA analysis.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.2
• /
• pp.12-21
• /
• 1982

Red pine and Japanese larch (Larix leptolepis Gordon) grown in Korea have been the main species of coniferous resources in Korea. Especially, planting area of Japanese larch has been increased continueously in the recent years due to its superior plant type and rapid growth rate and its stocks reached approximately 4.32 million cubic meters at the present time. Although many research works have been done for the utilization of the larch wood in various ways, still many problems are existed in its chemical applications due to a large proportion of soluble extractives. In this study, chemical composition of larch extractives and chemical structure of its major component were analyzed. In order to identify the basic structure of major component, gas-liquid chromatography for separation of some completely methylated alditols as their acetates on a 3% - ECNSS-M on Gas Chrom Q. column was used. Proportion of extractives of Japanese larch wood was higher than that of other conifers and major component of the soluble extractives was arabinogalactan, a schematic structural formula which was presented in Figure 2. The molar ratio of arabinose and galactose was 1:4.5. The main chain of arabinogalactan was composed of 1,3 linked ${\beta}$-D-galactopyranose residues, each of which carried a side chain, attached to the C-6 positions. The exact nature of all of the side chains is not known, but the majority of these side chain was composed of 1, 6 linked ${\beta}$-D-galactopyranose residues, with 2~3 such units present per average chain. Some of the galactose units in the main chain had a residue of 3 - 0 - ${\beta}$-L-arabinopyranosyl-L-arabinofuranose. In addition, a few terminal residues of D-glucuronic acid also was confirmed, attached to C-6 position of the D-galactopyranose residue. It could concluded that the main structure of highly branched arabinogalactan from Japanese larch extractive was essentially the same as those of the other larch species.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.4
• /
• pp.60-66
• /
• 1995

The treatability of Japanese larch heartwood was assessed by pressure treatment of non-incised dimension material with CCA or CCFZ. The effectiveness of incising(conventional, high density, and needle incising) for improving CCA treatability on refractory Japanese larch heartwood was also investigated. Preservative retention and penetration were somewhat greater with CCFZ treatment, although those was generally poor in both preservatives. The retention gradients for both CCA and CCFZ-treated stock were essentially the same shape. Treatment of non-incised material with CCA acheived the recommended treatability for using treated wood at the regions of hazard class H2 in the Japanese Agricultural Standards. However, Japanese larch heartwood would require incising as a pretreatment for enhancing treatability, if CCA-treated larch is intended to be used at the regions of hazard class H3 and H4. As expected, incising resulted in a considerable improvement of preservative treatability, particularly penetration, and the effect of incising on the improvement of treatability was excellent at the sequence of needle incising, high density incising, and conventional incising. Among incising techniques investigated in this study, high density and needle incising enhanced CCA treatability beyond the point where it did meet a minimum requirements specified by the Japanese Agricultural Standards for using CCA-treated Japanese larch at the regions of hazard class H3 and even H4.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.1
• /
• pp.52-59
• /
• 2001

The fixation characteristics of CCA and CCFZ in Japanese red pine, Japanese larch, and ezo spruce sapwood were compared at various temperatures and fixation conditions (drying and nondrying fixation). Fixation was monitored by the rates of reduction of hexavalent chromium to trivalent one, and optimal fixation time was estimated based on the results. The rate of fixation was highly temperature dependent, and the fixation rate of treated wood conditioned under nondrying conditions was much more faster than that under drying conditions, especially when the moisture content of treated wood was below fiber saturation point. Preservative types affected fixation; CCA-Type B had the highest fixation rate, followed by CCA-Type C and then CCFZ. The differences in fixation rates of preservative components were also observed among wood species; Japanese red pine fixed the fastest, followed by Japanese larch and then ezo spruce. Time required to complete fixation according to the fixation temperature could be predicted successfully using the regression equations between the temperatures and fixation time, regardless of conditioning methods, preservative types, and wood species.

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.1
• /
• pp.1-9
• /
• 2012

Densified fuels from biomass are widely used in North America and Europe as a regenerable and clean bioenergy. In this study, the fuel characteristics and densification characteristics of Japanese larch and Hyunsasi poplar were studied using a piston-type briquetting machine. The effects of pressure, pressure holding time, species, and particle size on briquette characteristics were studied. At room temperature, the highly densified briquettes of Japanese larch and Hyunsasi poplar can be produced at a compression pressure of 110~170 MPa. The produced briquettes have densities between 0.66 and 0.94 g/$cm^3$ after 28 days of storage at room temperature. The optimum pressure holding time was found to be 12 seconds. There is a linear increase in pressure with increase in density. The densities of briquettes from Japanese larch were higher than those of briquettes from Hyunsasi poplar. Also, the coarser particle size resulted in higher densities in briquettes than the finer particle size.

• Journal of the Korean Wood Science and Technology
• /
• v.49 no.1
• /
• pp.57-66
• /
• 2021

In recent years, the use of cross laminated timber (CLT) has been evolving. In addition, CLT manufactured with various species such as Japanese cedar has been developed to utilize the local resources in each country. However most factories in Japan produce CLT by bonding the laminae in width direction for orthogonal layers, where grain of element is perpendicular to the grain of outer layer, and this process is considered to be one of the factors that reduce productivity. A new wood based material (hereinafter referred to as Ply-lam) using wooden panel such as plywood for the orthogonal layer was developed in order to improve productivity in CLT manufacturing and improve quality. Japanese cypress lamina was used for the parallel layer, where grain of element is parallel to the grain of outer layer, of CLT and Korean larch plywood was used for the orthogonal layer, in order to effectively use Korean larch and expand the utilization of Japanese cypress. The cross-sectional construction of the Ply-lam was 5-layers 5-plies, and the dimensions were 1000 mm (width) × 150 mm (depth) × 4000 mm (length). As a performance evaluation of the manufactured Ply-lam, strength tests such as out-of-plane bending, in-plane bending, out-of-plane shearing and in-plane shearing tests were carried out. As the result of this study, Ply-lam composed of Japanese cypress lamina panels and Korean larch plywood showed very higher out-of-plane bending strength compared to the standard strength of CLT. And the result obtained in other tests seems to show a sufficiently high value.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.2
• /
• pp.195-201
• /
• 2017

This study was conducted to evaluate the resistance of heat-treated wood using the catalyst to decay caused by fungi for sapwood and heartwood of two tree species, Korean red pine (Pinus densiflora) and Japanese larch (Larix kaempferi), respectively. Wood samples were immersed for 10 min in sulfuric acid (7.5%) and then heat-treated at $130^{\circ}C$ for 90 min. Fomitopsis palustris, a brown-rot fungus, was used to examine the decay resistance of Korean red pine and Japanese larch wood. Weight and density of wood from the all conditions increased after heat treatment using the catalyst. Weight loss after decay resistance test was also dropped with a heat treatment. The lowest weight loss indicated at heat-treated heartwood of Japanese larch. Heat treatment using the catalyst effectively increased the resistance of wood to decay caused by fungi.

• Journal of the Korean Wood Science and Technology
• /
• v.50 no.4
• /
• pp.237-245
• /
• 2022

This study examined the structural performance of experimental parallel strand lumber (PSL) from a Larch veneer strand. The prototype of PSL from a Larch veneer strand was manufactured in the experimental laboratory and tested. The bending and dowel bearing strength were determined from the modulus of elasticity (MOE), modulus of rupture (MOR), and dowel bearing strength based on a 5% offset yield load. The test results indicated that the average MOR of PSL was higher than that of 2 × 4 dimension lumber, and the average MOE of PSL was lower than that of 2 × 4 dimension lumber. A linear relationship was observed between the MOR and MOE. The allowable bending stress of PSL was derived as specified in ASTM D2915 and compared with other research. The dowel bearing strength of PSL in parallel to the grain was approximately double that perpendicular to the grain of PSL. A comparison of several theoretical calculations based on each national code for the dowel bearing strength was conducted, and some theoretical equations produced results closer to the experimental results when it was parallel to the grain, but the difference was higher in the case perpendicular to the grain. The test results showed that PSL made with Japanese larch veneer strands appeared to be suitable for a raw material of structural composite lumber (SCL) appeared to be used as a raw material for SCL.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.2
• /
• pp.112-118
• /
• 2014

The depth effect on bending strength of Japanese larch structural lumber was investigated by using the published data of two different depth lumbers with the same length. Depth effect parameters were derived from Weibull's weakest link theory and compared to the results from other researches. Depth effect on bending strength was significant for No.1 and No.3 lumber, but not insignificant for No.2 lumber. Calculated value of the depth effect adjustment factors was 0.21, 0.11 and 0.22 by lumber grade, respectively. These results were similar to those results from previous researches and supported depth effect on bending strength of lumber. An apparent depth adjustment factor has been proposed to 0.2 in the literatures. Based on this study, depth adjustment factor was considered to 0.2 as a conservative optimum design value that should be incorporated in domestic building code (KBC) for structural lumber.