• Journal of the korean academy of Pediatric Dentistry
• /
• v.33 no.2
• /
• pp.221-232
• /
• 2006

The purpose of this study was to investigate the effect of step-curing mode on polymerization shrinkage and contraction of composite resin restoration. Class I cavities were prepared on the extracted human premolars. The cavities were ailed with Filtek $Z-250^{TM}$ (hybrid resin, 3M ESPE, USA) and Filtek $flow^{TM}$ (flowable resin, 3M ESPE, USA) and cured with one of the following irradiation modes; Halogen 40sec with continuous curing, LED 10sec with continuous curing, and LED 13sec with step-curing. Contraction stress was measured with strain gauge which was connected to TML $Datalogger^{TM}$ (TDS-102, SOKKI, Japan) and resin-dentin interfaces were observed by scanning electron microscope. The results of present study can be summarized as follows : 1. Composite resin restoration showed transient expansion just after irradiation of curing light. Contraction stress was increased rapidly at the early phase of polymerization and reduced slowly as time elapsed (P<0.05) 2. $Filtek\;flow^{TM}$ showed lower contraction stress than Filtek $Z-250^{TM}$ regardless of curing modes. 3. LED step-curing mode showed lowest contraction stress in Filtek $Z-250^{TM}$ compared with other curing modes(P<0.05). 4. LED step-curing mode showed lowest contraction stress in $Filtek\;flow^{TM}$ compared with other curing modes(P<0.05), but difference in contraction stress was not so greate as in $Filtek\;Z-250^{TM}$. 5. Polymerization of composite resin by LED light with step-curing mode and halogen light with continuous ode resulted in better marginal sealing than LED light with continuous mode.

• Journal of the Korean Geographical Society
• /
• v.28 no.2
• /
• pp.148-162
• /
• 1993

There is much speculation that modern capi-talist society is undergoing fundamental and qualitative chnge towards flexible specialization. The purpose of this study is to examine this hypothesis. This paper focusses on: the idea of flexible specialization; the significance of this transition; industrial district; and the implicati-ons of this new production system for Korean industrial space. Main arguments of this study are as follows: First, as all different groups of researchers apply the idea of flexible specialization according to their own specifications, the current debate on this topic is not much fruitful. Not surpri-singly, the concept of flexible specialization has overlapped with subocontracting. This intergration of subcontracting into flexible specialization systems, however, is inappropriate because the two concepts have different historical contexts. The other cause of this controversy is its inherent weekness, conceptual ambiguity. Thus, today's flexibility becomes tomorrow's rigidity. Secondly, transition towards flexible speciali-zation has only been partially achieved even in advanced capitalist countries. The application of dualistic explanatory framework, such as rigidity versus flexibiity, mass production versus small-lot multi-product production, and de-skilling versus re-skilling, has resulted in great exaggeration of the transformation, from Fordism to post-Fordism. There is no intermediary part between two places. Considering that the workers allocated to the Fordist mass production assembly line are not as large as one might imagine, the shift from mass to flexible production has only limited implications for the transformation of capitalist economy. Thirdly, 'industrial district' contorversy has contributed to highlighting the importance of small firms and areas as production space. The agglomeration of small firms in specific areas is common in Korea, but it is quite different from the industrial district based on flexible specialization. The Korean phenomenon stems from close interactions with its major parent firm rather than interactions between flexible, specialized, autonomous and technology-intensive smll firms. Most Korean subcontractors are still low-skilled, labour-intensive, and heavily dependent on their mojor parent firms. Thus, the assertion that the Seoul Metropolitan Area adopts flexible specialization has no base. Fourthly, the main concern of flexible speciali zation is small firms. However, the corporate organization that needs product diversification and technological specialization is oligopolistic large corporations typified by multinational corporations. It is because of this that most of these organizations are adoptiong Fordist mass production methods. The problem of product diversification will be resolved naturally if economic internationalization progresses further. What is more important for business success is the quality and price competitiveness of firms rather than product diversification. Lastly, in order to dispel further misunderst-anding on this issue, it is imparative that the conceptual ambiguity is resolved most urgently. This study recommends adoption of more speci-fied and direct terminology (such as, factory automation, computer design, out-sourcing, the exploitation of part-time labor, job redesign) rather than that of ideological ones (such as, Taylorism, Fordism, neo-Taylorism, neo-Fordism, post-fordism, flexible specialization, peripheral post-Fordism). As the debates on this topic just started, we still have long way to go until consensus is reached.

• (The)Study of the Eastern Classic
• /
• no.68
• /
• pp.283-317
• /
• 2017

Issues over morality and profit usually address relations between moral principles and material gains. In the history of traditional Oriental philosophy, discussions about them were called "Yi-Li zhi bian." The ideas of Confucius and Mencius also contain various discussions about Yi-Li. Both Confucius and Mencius defined Yi as a value concept to represent "natural," "appropriate" or "just" and regarded Yi as an external moral principle on the one hand and an internal moral emotion on the other hand. They had, at the same time, differences, as well. While Confucius placed importance on the external and acquired nature of Yi as a goal of morality, Mencius argued for the internal and innate nature of Yi as the nature of morality partially while recognizing its externality overall. Such Yi is a general term for subjective moral emotions and objective moral principles. Li was a concept of fact to represent "gain," "profit" or "profit-making." Both of them were against private interest and emphasized public interest. As for their differences, Confucius was positive about Li to some degree by saying "One should think of Yi when making profit," whereas Mencius was almost negative about Li and perceived it to be for Yi by saying "One should give up even his own life for Yi." He meant Li's dependence on Yi and also Yi's absoluteness for Ri. Both of them found a mix of opposite features in Yi such as internality and externality, subjectivity and objectivity, specificity and generality, and uniqueness and universality and also in Li such as individuality and specialty and public and private interest. Those features have both disadvantages including theoretical irrationality and logical contradiction and advantages including ideological diversity and conceptual polysemy. If efforts are made to avoid their disadvantages and highlight their advantages, they will provide some elements to consult in the creation of new global ethics required today when East and West are becoming one. In the modern society, the Yi-Li issues can be divided into the issues of morality and economy, personal and social profit, and moral ideal and material gain. If these modern Yi-Li issues are combined with the traditional Yi-Li issues, two paths will emerge over the order of Yi-Li. Of the many perceptions of Yi-Li issues of Confucius and Mencius, the idea of "Yi First, Li Later" can be very useful for creating a new ethics theory to represent "humanism" that we all need today when everyone considers their own pursuit of profit and satisfaction of needs as the best values. Sound Yi-Li relations will be possible only through Yi's orientation toward externality based on internality and Li's pursuit of private interest on the premise of public interest according to the spirit of "Yi First, Li Later."

• Journal of the Korean Association of Geographic Information Studies
• /
• v.25 no.4
• /
• pp.94-106
• /
• 2022

In order to increase timber self-sufficiency, Korea's 6th Basic Forest Plan aims to increase the density of forest roads to 12.8 m ha^-1 by 2037. However, due to rapid re-forestation, current management infrastructure is insufficient, with just 4.8 m ha^-1 of forest roads in 2017. This is partly due to time and cost limitations on the process of forest road feasibility evaluation, which considers factors such as topography and forest conditions. To solve this problem, we propose an eco-friendly and efficient forest road network planning method using a geographic information system (GIS), which can evaluate a potential road site remotely based on spatial information. To facilitate such planning, this study identifies forest road construction priorities that can be evaluated using spatial information, such as topography, forest type and forest disasters. A method of predicting the optimal route to connect a forest road with existing roads is also derived. Overlapping analysis was performed using GIS-MCE (which combines GIS with multi-criteria evaluation), targeting the areas of Cheongsong-gun and Buk-gu, Pohang-si, which have a low forest-road density. Each factor affecting the suitability of a proposed new forest road site was assigned a cost, creating a cost surface that facilitates prioritization for each forest type. The forest path's optimal route was then derived using least-cost path analysis. The results of this process were 30 forestry site recommendations in Cheongsong-gun and one in Buk-gu, Pohang-si; this would increase forest road density for the managed forest sites in Cheongsong-gun from 1.58 m ha^-1 to 2.55 m ha^-1. This evaluation method can contribute to the policy of increasing timber self-sufficiency by providing clear guidelines for selecting forest road construction sites and predicting optimal connections to the existing road network.

• The Korean Journal of Air & Space Law and Policy
• /
• v.29 no.2
• /
• pp.109-134
• /
• 2014

Regulation (EC) No 261/2004 of the European Parliament and of the Council of 11 February 2004 establishing common rules on compensation of assistance to passengers in the event of denied boarding and of cancellation or long delay of flights (Regulation No 261/2004) provides extra protection to air passengers in circumstances of denied boarding, cancellation and long-delay. The Regulation intends to provide a high level of protection to air passengers by imposing obligations on air carriers and, at the same time, offering extensive rights to air passengers. If denied boarding, cancellation and long-delay are caused by reasons other than extraordinary circumstances, passengers are entitled for compensation under Article 7 of Regulation No 261/2004. In Wallentin-Hermann v Alitalia-Linee Aeree Italiane SpA(Case C-549/07, [2008] ECR I-11061), the Court did, however, emphasize that this does not mean that it is never possible for technical problems to constitute extraordinary circumstances. It cited specific examples of where: an aircraft manufacturer or competent authority revealed that there was a hidden manufacturing defect on an aircraft which impacts on safety; or damage was caused to an aircraft as a result of an act of sabotage or terrorism. Such events are not inherent in the normal exercise of the activity of the air carrier concerned and is beyond the actual control of that carrier on account of its nature or origin. One further point arising out of the court's decision is worth mentioning. It is not just necessary to satisfy the extraordinary circumstances test for the airline to be excused from paying compensation. It must also show that the circumstances could not have been avoided even if all reasonable measures had been taken. It is clear from the language of the Court's decision that this is a tough test to meet: the airline will have to establish that, even if it had deployed all its resources in terms of staff or equipment and the financial means at its disposal, it would clearly not have been able - unless it had made intolerable sacrifices in the light of the capacities of its undertaking at the relevant time - to prevent the extraordinary circumstances with which it was confronted from leading to the cancellation of the flight.

• Radiation Oncology Journal
• /
• v.20 no.1
• /
• pp.81-90
• /
• 2002

Purpose : To establish and verify the proper and the practical IMRT (Intensity--modulated radiation therapy) patient QA (Quality Assurance). Materials and Methods : An IMRT QA which consists of 3 steps and 16 items were designed and examined the validity of the program by applying to 9 patients, 12 IMRT cases of various sites. The three step OA program consists of RTP related QA, treatment information flow QA, and a treatment delivery QA procedure. The evaluation of organ constraints, the validity of the point dose, and the dose distribution are major issues in the RTP related QA procedure. The leaf sequence file generation, the evaluation of the MLC control file, the comparison of the dry run film, and the IMRT field simulate image were included in the treatment information flow procedure QA. The patient setup QA, the verification of the IMRT treatment fields to the patients, and the examination of the data in the Record & Verify system make up the treatment delivery QA procedure. Results : The point dose measurement results of 10 cases showed good agreement with the RTP calculation within $3\%$. One case showed more than a $3\%$ difference and the other case showed more than $5\%$, which was out side the tolerance level. We could not find any differences of more than 2 mm between the RTP leaf sequence and the dry run film. Film dosimetry and the dose distribution from the phantom plan showed the same tendency, but quantitative analysis was not possible because of the film dosimetry nature. No error had been found from the MLC control file and one mis-registration case was found before treatment. Conclusion : This study shows the usefulness and the necessity of the IMRT patient QA program. The whole procedure of this program should be peformed, especially by institutions that have just started to accumulate experience. But, the program is too complex and time consuming. Therefore, we propose practical and essential QA items for institutions in which the IMRT is performed as a routine procedure.

• Journal of Korean Society of Transportation
• /
• v.23 no.7 s.85
• /
• pp.159-163
• /
• 2005

The propriety between suppliers and demanders in geometric design is very important. Although the final purpose of constructing roads is to concern about the driver s comfort, unfortunately, it has not been considered so far. We've considered the regularity and quickness in considering driver's comfort but there should be considered the safety for the accident as well. If drivers are appeared to be more speeding than designer's intention, there will be needed some supplements to increase the safety rate for the roads. Even if both an upward and downward section are supposed to exist at the same time for solid geometry of the roads like this, it is true that the recent design for the 3-D solid geometry section has been done as flat 2-D and the minimum plane curve radius and the maximum cant have been decided just by calculating without considering operating speed between an upward and downward section at the same point. In this investigation, thus, I'd like to calculate the safety of the cant by considering the speed features of the solid geometry for the first lane of four lane rural roads. To begin with, we investigated the driving speed of the car, which is not been influenced by a preceding car to analyze the influence of the geometrical structure by using Nc-97. Secondly, we statistically analyzed the driving features of the solid geometry after comparing the 6 sections, that is, measuring the driving speed feature at 12 points and combining the influence of the vertical geometry and plane geometry to the driving speed of the plane curve which was researched before. Finally, we estimated the value of cant which considers the driving speed not by using it which has applied uniformly without considering it properly, though there were some differences between a designed speed and driving speed through the result of the basic statistical analysis but by introducing the new safety rate rule, a notion of ${\alpha}$. As a result of the research, we could see the driving features of the car and suggest the safety rate which considers these. For considering the maximum cant, if we apply the safety rate, the result of this experiment, which considers 3-D solid geometry, there'll be the improvement of the driver's safety for designing roads. In addition, after collecting and analyzing the data for the road sections which have various geometrical structures by expanding this experiment it is considered that there should be developed the models which considers 3-D solid geometry.

• Journal of Chest Surgery
• /
• v.31 no.8
• /
• pp.739-748
• /
• 1998

Background: It has been well documented that transient occlusion of the coronary artery causes myocardial ischemia and finally cell death when ischemia is sustained for more than 20 minutes. Extensive studies have revealed that ischemic myocardium cannot recover without reperfusion by adequate restoration of blood flow, however, reperfusion can cause long-lasting cardiac dysfunction and aggravation of structural damage. The author therefore attempted to examine the effect of postischemic reperfusion on myocardial ultrastructure and to determine the rationales for recanalization therapy to salvage ischemic myocardium. Materials and methods: Young Holstein-Friesian cows(130∼140 Kg body weight; n=40) of both sexes, maintained with nutritionally balanced diet and under constant conditions, were used. The left anterior descending coronary artery(LAD) was occluded by ligation with 4-0 silk snare for 20 minutes and recanalized by release of the ligation under continuous intravenous drip anesthesia with sodium pentobarbital(0.15 mg/Kg/min). Drill biopsies of the risk area (antero-lateral wall) were performed at just on reperfusion(5 minutes), 1-, 2-, 3-, 6-, 12-hours after recanalization, and at 1-hour assist(only with mechanical respiration and fluid replacement) after 12-hour recanalization. The materials were subdivided into subepicardial and subendocardial tissues. Tissue samples were examined with a transmission electron microscope (Philips EM 300) at the accelerating voltage of 60 KeV. Results: After a 20-minute ligation of the LAD, myocytes showed slight to moderate degree of ultrastructural changes including subsarcolemmal bleb formation, loss of nuclear matrix, clumping of chromatin and margination, mitochondrial destruction, and contracture of sarcomeres. However, microvascular structures were relatively well preserved. After 1-hour reperfusion, nuclear and mitochondrial matrices reappeared and intravascular plugging by polymorphonuclear leukocytes or platelets was observed. However, nucleoli and intramitochondrial granules reappeared within 3 hours of reperfusion and a large number of myocytes were recovered progressively within 6 hours of reperfusion. Recovery was apparent in the subepicardial myocytes and there were no distinct changes in the ultrastructure except narrowed lumen of the microvessels in the later period of reperfusion. Conclusions: It is likely that the ischemic myocardium could not be salvaged without adequate restoration of coronary flow and that the microvasculature is more resistant to reversible period of ischemia than subendocardium and subepicardium. Therefore, thrombolysis and/or angioplasty may be a rational method of therapy for coronarogenic myocardial ischemia. However, it may take a relatively longer period of time to recover from ischemic insult and reperfusion injury should be considered.

• Journal of Science of Art and Design
• /
• v.9
• /
• pp.5-24
• /
• 2006

Human hunted and picked to survive and a vessel was made naturally to store something being hunted and picket, which was a great invention. In modern times, society changed and development of science gave us convenience in making a vessel and various kinds of store instruments which was made of pure natural material, of new stuff, such as plastic and iron. but human became to be inclined to regress into nature because of problems of environment. We can say that the representative trend is well-being, after all this is a symptom to return to life being persued by predecessors before the science civilization was developed. Ancestors have lived with nature, adapted themselves to it. For examples they have built the house which became to be a part of nature and just like it, and studied a method of storing food to eat for four seasons, then displayed a storagehouse and storage containers everywhere of the house. Now Korean has the custody of kimchi in refrigerator at every house, but our forefathers controled a timing to eat food with studying a method of storage to put to use nature. With hot wind of well-being, Korean food is becoming to be globalized, according to this, concern about the wisdom of progenitors is growing more and more. It's an example that the world shows concern seriously about the pottery, which have stored kimchi for a long time fleshly, in globalization of kimchi. This study have three purposes, the first. checking documents about the development history of pottery which is a kind of ceramic, and then the second, through an scientific experiment, with studying characteristic of pottery being built by the wisdom of ancestors, informing the merit of pottery and necessity to the world, and futhermore, the third, working up the development of close environmental vessels putting to use the characteristic of pottery.

• The Korean Journal of Pain
• /
• v.2 no.2
• /
• pp.155-166
• /
• 1989

Bonica defined, that reflex sympathetic dystrophy (RSD) may develop pain, vasomotor abnoramalities, delayed functional recovery, and dystrophic changes on an affected area without major neurologic injury following trauma, surgery or one of several diseased states. This 45 year old male patient had been crushed on his left shoulder by a heavily laden rear car, during his job street cleaning about 10 years ago (1978). At first the pain was localizea only to the site of injury, but with time, it spreaded from the shoulder to the elbow and hand, with swelling. X-ray studies in the local clinic, showed no bone abnormalities of the affected site. During about 10 years following the injury, the had recieved several types of treatments such as nonsteroidal analgesics, steroid injections into the glenoidal cavity (10 times), physical therapy, some oriental herb medicines, and acupuncture over a period of 1~3 months annually. His shoulder pain and it's joint dysfunction persisted with recurrent paroxysmal aggrevation because of being mismanaged or neglected for a sufficiently long period these fore permiting progression of the sympathetic imbalance. On July 14 1988 when he visited our clinic. He complained of burning, aching and had a hyperpathic response or hyperesthesia in touch from the shoulder girdle to the elbow and the hand. Also the skin of the affected area was pale, cold, and there was much sweating of the axilla and palm, but no edema. The shoulder girdle was unable to move due to joint pain with marked weakness. We confirmed skin temperatures $5^{\circ}C$ lower than those of the unaffected axilla, elbow and palm of his hand, and his nails were slightly ridged with lateral arching and some were brittle. On X-ray findings of both the shoulder AP & lateral view, the left humerus and joint area showed diffuse post-traumatic osteoporosis and fibrous ankylozing with an osteoarthritis-like appearance. For evaluating the RSD and it's relief of pain, the left cervical sympathetic ganglion was blocked by injecting 0.5% bupivacaine 5 ml with normal saline 5 ml (=SGB). After 15 minutes following the SGB, the clinical efficacy of the block by the patients subjective score of pain intensity (=PSSPI), showed a 50% reduction of his shoulder and arm pain, which was burning in quality, and a hyperpathic response against palpation by the examiner. The skin temperatures of the axilla and palm rose to $4{\sim}5^{\circ}C$ more than those before the SGB. He felt that his left face and upper extremity became warmer than before the SGB, and that he had reduced sweating on his axilla and his palm. Horner's sign was also observed on his face and eyes. But his deep shoulder joint pain was not improved. For the control of the remaining shoulder joint pain, after 45 minutes following the SGB, a somatic sensory block was performed by injecting 0.5% bupivacaine 6 ml mixed with salmon calcitonin, $Tridol^{(R)}$, $Polydyn^{(R)}$ and triamcinolone into the fossa of the acromioclavicular joint region. The clinical effect of the somatic block showed an 80% releif of the deep joint pain by the PSSPI of the joint motion. Both blocks, as the above mentioned, were repeated a total of 28 times respectively, during 6 months, except the steroid was used just 3 times from the start. For maintaining the relieved pain level whilst using both blocks, we prescribed a low dose of clonazepam, prazocin, $Etravil^{(R)}$, codeine, etodolac micronized and antacids over 6 months. The result of the treatments were as follows; 1) The burning, aching and hyperpathic condition which accompanied with vaosmotor and pseudomotor dysfunction, disappeared gradually to almost nothing, within 3 weeks from the starting of the blocks every other day. 2) The joint disability of the affected area was improved little by little within 6 months. 3) The post-traumatic osteoporosis, fibrous ankylosis and marginal sclerosis with a narrowed joint, showed not much improvement on the X-ray findings (on April 25, 1989) 10 months later in the follow-up. 4) Now he has returned to his job as a street cleaner.