• Nuclear Engineering and Technology
• /
• v.51 no.2
• /
• pp.546-555
• /
• 2019

Since the first nuclear reactor first critical, nuclear systems has gone through four generations of history, and the fourth generation nuclear system will be truly realized in the near future. The notions of SVBR and lead-bismuth eutectic alloy coolant put forward by Russia were well received by the international nuclear science community. Lead-bismuth eutectic alloy with the ability of the better neutron economy, the low melting point, the high boiling point, the chemical inertness to water and air and other features, which was considered the most promising coolant for the 4th generation nuclear reactors. This study mainly focuses on the structural design optimization of the 4th-generation reactor coolant pump, including analysis of external characteristics, inner flow, and transient characteristic. It was found that: the reactor coolant pump with a central symmetrical dual-outlet volute structure has better radial-direction balance, the pump without guide vane has better hydraulic performance, and the pump with guide vanes has worse torsional vibration and pressure pulsation. This study serves as experience accumulation and technical support for the development of the 4th generation nuclear energy system.

• Nuclear Engineering and Technology
• /
• v.51 no.2
• /
• pp.600-606
• /
• 2019

Studies on the application of the lead rubber bearing (LRB) isolation system to nuclear power plants are being carried out as one of the measures to improve seismic performance. Nuclear power plants with isolation systems require seismic probabilistic safety assessments, for which the seismic fragility of the structures, systems, and components needs be calculated, including for beyond design basis earthquakes. To this end, seismic response analyses are required, where it can be seen that the behaviors of the isolation system components govern the overall seismic response of an isolated plant. The numerical model of the LRB used in these seismic response analyses plays an important role, but in most cases, the extreme performance of the LRB has not been well studied. The current work therefore develops an extreme nonlinear numerical model that can express the seismic response of the LRB for beyond design basis earthquakes. A full-scale LRB was fabricated and dynamically tested with various input conditions, and test results confirmed that the developed numerical model better represents the behavior of the LRB over previous models. Subsequent seismic response analyses of isolated nuclear power plants using the model developed here are expected to provide more accurate results for seismic probabilistic safety assessments.

• Korean Journal of Materials Research
• /
• v.31 no.8
• /
• pp.471-479
• /
• 2021

The electrochemical reaction between lead borate glass frit doped with Sn metal filler and Ni-Cr wire of a J-type resistor during a term of Joule heating is investigated. The fusing behavior in which the Ni-Cr wire is melted is not observed for the control group but measured for the Sn-doped specimen under 30 V and 500 mA. The Sn-doped lead borate glass frit shows a fusing property compared with other metal-doped specimens. Meanwhile, the redox reaction significantly contributes to the fusing behavior due to the release of free electrons of the metal toward the glass. The electrons derived from the glass, which used Joule heat to reach the melting point of Ni-Cr wire, increase with increasing corrosion rate at interface of metal/glass. Finally, the confidence interval is 95 ± 1.95₉ %, and the adjusted regression coefficient, R in the optimal linear graph, is 0.93, reflecting 93% of the data and providing great potential for fusible resistor applications.

• Journal of the Korean Society of Visualization
• /
• v.22 no.1
• /
• pp.18-27
• /
• 2024

A series of shock wave pulses with Mach number 2.2 of 100, 200, and 300 shocks were applied to lead sulfide (PbS) nanomaterials at intervals of 5 sec per shock pulse. To investigate the crystallographic, electronic, and magnetic phase stabilities, powder X-ray diffractometry (XRD), diffused reflectance spectroscopy (DRS), and vibrating-sample magnetometry (VSM) were employed. The material exhibited a rock salt structure (NaCl-type structure); XRD results indicated that material is monoclinic with space group C121 (5). Further, XRD results showed shifts due to lattice contraction and expansion when material was subjected to shock wave pulses, indicating stable material structure. Based on the data obtained, we believe that the PbS material is a good choice for high-pressure, high-temperature, and aerospace applications due to its superior shock resistance characteristics.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.802-804
• /
• 2002

An analysis of the skeleton type BLDC motor is presented. The single phase skeleton type BLDC motor consists of the stator, rotor with the permanent magnet, and drive circuit with hall sensors that detect the rotor position. The major factors for the initial starting, efficiency, and torque ripples of the skeleton type BLDC motor are the detent groove of the stator and the lead angle of the phase voltage. The performance characteristics according to the angle and height of the detent groove is analyzed. The optimum lead angles of the phase voltage with the torque ripple and motor efficiency is described using the finite element method.

• Journal of Power System Engineering
• /
• v.13 no.6
• /
• pp.129-136
• /
• 2009

A motor cylinder is widely used as an apparatus for transportation of a small scale load. It is, however, difficult for only one motor cylinder to transfer a large scale load such as a weir. The large scale load is transferred by two motor cylinders which are mounted on right and left of load itself. In this case, the displacement difference generated between two motor cylinders, namely, the synchronous error has a bad influence on the transportation. In this study, a synchronous control system is designed to restrain synchronous error caused by skew disturbance. The control system is composed of two disturbance observers and one synchronous controller. Each disturbance observer is designed to restrain the skew disturbance. And the synchronous controller is designed to achieve stable and accurate synchronization. Finally, the simulation results show that the designed control system is effective for the skew disturbance which lead to synchronous error.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.721-723
• /
• 1992

The electrical resistivity and piezoelectric properties have been studied for Lead Zirconate-Titanate(PZT) with $Nb_2O_5$ dopant, fabricated from conventional mixed-oxide powders and molten salt synthesis. The resistivity and electromechanical coupling factor(Kp) were increased with increasing Nb contents. The reason for increasing of the electrical resistivity below the Curie Temperature(Tc), It is believed that the p-type electrical conduction in PZT is caused by the lead vacancies. The electromechanical coupling factor(Kr) and piezoelectric constant $d_{33}$ were improved by Nb additives. This behavior can be explained as a compensation effect and $Nb^{5+}$ can serve as a donar and contribute electrons to the conduction process. As a result, the optimized $Nb_2O_5$ dopants on the PZT specimens were 0.75 wt%.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1414-1416
• /
• 2001

Crack-free and homogeneous compact and epitaxial lead zirconate titanate(PZT) ferroelectric thin films with perovsikte structure have been prepared by sol-eel method. Tetrabutyl titanate, lead acetate and zirconium nitrate are used as raw materials. Glacial acetic acid is used as a catalyst. Ethylene glycol monoethyl ether is used as a solvent. The annealing temperatures of th thin films are 600~900$^{\circ}C$. The values of the remanent polarization Pr, and the coercive field $E_c$, of the PZT ceramic thin films are 46, 35 ${\mu}C/cm^2$ respectively.

• Transactions of Materials Processing
• /
• v.23 no.4
• /
• pp.206-210
• /
• 2014

The metal lead frame, a semiconductor component, has product tolerances in micro units as compared to products made with a larger size mold. Therefore, small deflections of the mold and of the press as well as the press molding process itself have a strong influence on accuracy of the product. Hence, it is necessary for the process design to consider the structural response of the mold and the press during deformation. In the current study, the mold deflection and pressure on the punch is examined using the finite element modeling (FEM) program ABAQUS. The results from the simulation were verified with the dynamic deformation measurement equipment using digital image correlation (DIC).

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.15-20
• /
• 2000

We demonstrated a single balanced mixer of the combination of high-T. superconductor (HTS) and III-V GaAs beam lead Schottky diodes operating in the mini-cryogenic chamber. The HTS hybrid mixer was designed with a center frequency of 27.5 GHz and a bandwidth of 1 GHz, and consisted of a rat-race coupler circuit with beam-lead diodes attached to its balanced ports. The HTS hybrid mixer with 1 GHz RF bandwidths exhibits a conversion loss of 6 dB. A LO-to-RF isolation was greater than 40 dB in the range of operating frequencies. Since the HTS/III-V hybrid mixer devices have lower noise and conversion loss, this technique provide us with new capabilities that can be effectively utilized in the field of local-point distribution service (LMDS) systems.