• Nuclear Engineering and Technology
• /
• v.55 no.10
• /
• pp.3692-3699
• /
• 2023

The Rare isotope Accelerator complex for ON-line experiments in Korea houses several accelerator complexes. Among them, the µSR facility will be initially equipped with a 600 MeV and 100 kW proton beam to generate surface muons, and will be upgraded to 400 kW with the same energy. Accelerated proton beams lose approximately 20% of the power at the target, and the remaining power is concentrated in the beam direction. Therefore, to ensure safe operation of the facility, concentrated protons must be distributed and absorbed at the beam dump. Additionally, effective dose levels must be lower than the legal standard, and the beam dumps used at 100 kW should be reused at 400 kW to minimize the generation of radioactive waste. In this study, we introduce a tailored method for designing beam dumps based on the characteristics of the µSR facility. To optimize the geometry, the absorbed power and effective dose were calculated using the MCNP6 code. The temperature and stress were determined using the ANSYS Mechanical code. Thus, the beam dump design consists of six structures when operated at 100 kW, and a 400 kW beam dump consisting of 24 structures was developed by reusing the 100 kW beam dump.

• Nuclear Engineering and Technology
• /
• v.56 no.7
• /
• pp.2489-2497
• /
• 2024

The current study aims to develop new clay bricks doped with metallic waste for radiation shielding applications. The aforementioned new bricks were fabricated with various metallic waste concentrations under a pressure rate reaching ≈114 MPa and firing temperature of 1100 ℃. The impacts of the metallic waste and the firing temperature on the developed brick samples' physical, radiation shielding, and structural properties were studied. In order to identify the fabricated bricks' mineral content, the X-ray diffraction pattern was used. Additionally, the fabricated bricks' porosity and density were experimentally determined, where the porosity was reduced by 28.03%, while their densities increased by ≈ 10.5% by raising the concentration of metallic waste. The linear attenuation coefficient (LAC) for the developed brick was investigated experimentally using a NaI (Tl) scintillation detector over the 0.033-1.408 MeV energy interval. The measured LAC values were enhanced by increasing the concentrations of metallic waste within the fabricated bricks over the examined energy interval. The fabricated brick's LAC enhancement improves the gamma-ray shielding characteristics. Therefore, the fabricated bricks are a cheap and suitable choice for radiation protection applications.

• Nuclear Engineering and Technology
• /
• v.56 no.7
• /
• pp.2437-2443
• /
• 2024

This work synthesized four glass samples with a fixed ratio of PbO to Na₂O and a variable ratio of BaO to B₂O₃. The linear attenuation coefficient (LAC) (μ, cm^-1) and additional attenuator parameters were determined experimentally using a semiconductor detector and different gamma sources. The comparison was carried out between the experimental and the XCOM calculated results, with good agreement emerging between the two results. The impacts of the BaO substituting for the B₂O₃ on fabricated PNBB glasses' radiation shielding properties were discussed. By increasing the BaO substitution concentration between 10 and 25 mol.%, the LAC μ values (cm^-1) increased by 76.60 %, 13.81 %, 12.56 %, and 12.52 % for the respective γ-ray energies of 0.059, 0.662, 1.173, and 1.332 MeV. The μ value reduction with raised gamma energy values increased the values of the calculated half-value thickness (Δ_0.5) as a result of the μ and Δ_0.5 values' reverse proportionality. Other shielding parameters such as the lead equivalent thickness (Δ_eq) and radiation protection efficiency were also determined for the present PNBB glass samples.

• Journal of Korea Water Resources Association
• /
• v.37 no.11
• /
• pp.969-978
• /
• 2004

According to the report of hydrologic modeling study, from a quantitative point of view, a lumped model is more efficient than a distributed model. A distributed model has to simplify geospatial characteristics for the shake of restricted application on computer calculation and field observation. In this reason, a distributed model can not help having some errors of water quantity modelling. However, considering a distribution of rainfall-runoff reflected spatial characteristics, a distributed model is more efficient to simulate a flow of surface water, The purpose of this study is modeling of spatial rainfall-runoff of surface water using grid based distributed model, which is consisted of storage function model and essential basin-channel parameters( slope, flow direction & accumulation), and that procedure is able to be executed at a personal computer. The prototype of this model is developed in Heongseong Multipunose Dam basin and adapted in Hapchon Multipurpose Dam basin, which is larger than the former about five times. The efficiency coefficients in result of two dam basin simulations are more than about 0.9, but ones at the upstream water level gauge station meet with bad result owing to overestimated rating curves in high water level. As a result of this study, it is easily implemented that spatially distributed rainfall-runoff model using GIS, and geophysical characteristics of the catchment, hereafter it is anticipated that this model is easily able to apply rainfall data by real time.

• Applied Chemistry for Engineering
• /
• v.26 no.2
• /
• pp.165-172
• /
• 2015

Quercetin and its glycoside, rutin, are flavonoids, which are well known as natural antioxidants. In this study, cationic liposomes loaded with flavonoids (quercetin or rutin) were investigated for their effects on cell and skin permeability, and protective effects against UVA. The particle size of the empty cationic liposomes was in the range of 100~130 nm, and the zeta potential was + 33.05 mV. The entrapment efficiency of 0.5R/CL was higher than that of 0.5 Q/CL. The cellular uptake of the cationic liposomes was five-fold higher than that of liposomes. The skin permeability of quercetin and rutin was investigated using Franz diffusion cells. Compared to the initial loading dose, the amount of quercetin or rutin delivered to the skin by cationic liposomes was higher than that delivered by conventional liposomes or phosphate-buffered saline. From the protective effect of cationic liposomes against UVA ($25J/cm^2$), we found that the cell viability in cationic liposomes containing flavonoids was higher than that of using UVA irradiation only. These results indicate that cationic liposomes provide enhanced delivery of flavonoids (quercetin and rutin) into the skin and may be used for antiaging and antioxidant cosmetics.

• Journal of Life Science
• /
• v.20 no.2
• /
• pp.183-189
• /
• 2010

A fibrinolytic enzyme producing Bacillus sp. J-19 was isolated from the popular Korean seasoning, pickled anchovy. The fibrinolytic enzyme was purified to homogeneity by chromatographic methods including ethanol precipitation and gel-filtration using Sephadex G-50. Compared to the crude enzyme extract, the specific activity of the enzyme increased 1021-fold with a recovery of 23%. The purified enzyme was estimated to be approximately 45 kDa by SDS-PAGE. Especially, the amidolytic activity in the presence of the synthetic substrate for serine protease (H-D-Ile-Pro-Arg-pNA, S-2288) represented approximately 17 U/mg. In addition, more than the 60% activity of the 45 kDa fibrinolytic activity was maintained in the presence of up to 30% (w/v) sodium chloride. These findings could provide a unique fibrinolytic enzyme, leading to a potential thrombolytic agent.

• Journal of Sensor Science and Technology
• /
• v.2 no.1
• /
• pp.109-115
• /
• 1993

A CdS single crystal was grown by using sublimation method. Lattice constants, $a_{o}$ and $c_{o}$, obtained by using extrapolation were $4.131{\underline{8}}{\AA}$ and $6.712{\underline{2}}{\AA}$, respectively. The carrier density was${\sim}10^{23}m^{-3}$ and the mobility was $2.93{\times}10^{-2}m^{2}$/V sec from measured Hall data at room temperature. The mobility has a increasing tendency in proportion to $T^{1/2}$ from 33 K to 150 K and a decreasing tendency in proportion to $T^{-2}$ from 180 K to room temperature. The short wavelength band peak measured from photocurrent was due to intrinsic transition, and the energy value of this peak was equal to the energy band gap of CdS photoconductor.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04a
• /
• pp.33-35
• /
• 2008

We have fabricated and evaluated new high efficiency green light emitting phosphorescent devices with an emission layer of $[TCTA_{1/3}TAZ_{2/3}/TAZ]:Ir(ppy)_3$. The whole experimental devices have the basic structure of $2-TNATA(500 {\AA})/NPB(300{\AA})/EML(300{\AA})/BCP(50{\AA})/SFC137(500{\AA})$ between anode and cathode. We have also fabricated conventional phosphorescent devices with emission layers of $(TCTA_{1/3}TAZ_{2/3}):Ir(ppy)_3$ and $(TCTA/TAZ):Ir(ppy)_3$ and compared their electroluminescence characteristics with those of the device with an emission layer of $(TCTA/TCTA_{1/3}TAZ_{2/3}/TAZ):Ir(ppy)_3$. The current density(J), luminance(L), and current efficiency($\eta$) of the device with an emission layer of $(80{\AA}-TCTA/90{\AA}-TCTA_{1/3}TAZ_{2/3}/130{\AA}-TAZ):10%-Ir(ppy)_3$ were 95 $mA/cm^2$, 25000 $cd/m^2$, and 27 cd/A at an applied voltage of 10V, respectively. The maximum current efficiency was 52 cd/A under the luminance of 400 $cd/m^2$. The peak wavelength and FWHM(full width at half maximum) in the electroluminescence spectral were 513nm and 65nm, respectively. The color coordinate was (0.30, 0.62) on the CIE (Commission Internationale de l'Eclairage) chart. Under the luminance of 15000 $cd/m^2$, the current efficiency of the device with an emission layer of $(80{\AA}-TCTA/90{\AA}-TCTA_{1/3}TAZ_{2/3}/130{\AA}-TAZ):10%-Ir(ppy)_3$ was 34 cd/A, which has been improved 1.7 times and 1.4 limes compared to those of the devices with emission layers of $(300{\AA}-TCTA_{1/3}TAZ_{2/3}): 10%-Ir(ppy)_3$ and $(100{\AA}-TCTA/200{\AA}-TAZ):10%-Ir(ppy)_3$, respectively.

• Asian-Australasian Journal of Animal Sciences
• /
• v.14 no.1
• /
• pp.48-53
• /
• 2001

An in vitro study was conducted to examine the effect of sources and the addition levels of carbohydrates on fermentation characteristics, bacterial growth, and hydrogenation of linoleic acid ($C_{18:2}$) by mixed ruminal bacteria. Starch and cellobiose were added to the 200 ml non-selective basal media at the levels of 0.20 and 0.35% (w/v), respectively. Linoleic acid (66.8~79.6 mg) in the absorbed form into the pieces of nylon cloth was also added to the media of 5 treatments including control which was not added with carbohydrate. Three mls of rumen fluid strained through 12 layers of cheese cloth were added to each medium, and were incubated anaerobically in the shaking incubator of $39^{\circ}C$ for 24 hours. During 24 h incubation the pH in incubation media of all treatments was maintained above 6.6 by the addition of sodium bicarbonate. The pH and ammonia concentration of incubation media were not clearly influenced by the sources and addition levels of carbohydrates while additions of carbohydrates increased (p<0.0001) VFA concentration at the 24 h incubation. Molar proportions of acetate were reduced (p<0.0004) while those of propionate were increased (p<0.0006) by the addition of carbohydrates. But the differences in concentration and molar proportions of the VFA were small between the sources or the addition levels. Bacterial growth was faster (p<0.0004) in the starch added treatments than in the cellobiose added ones and control, but no differences were found between addition levels. Increased (p<0.0487) hydrogenation was observed from the starch added treatments compared to the cellobiose added ones, but there was no difference between addition levels.

• Solar Energy
• /
• v.18 no.1
• /
• pp.57-67
• /
• 1998

A study on a buoyancy effect by the temperature difference between a inner room air and a inflowing cool air and also by Inlet velocity can contribute greatly to enhance performance of air conditioning system, so the study on the distribution characteristics of inflowed cool air is important to analyze the cool air storage in a room. For this study, in the real-sized model room, the temperature differences between inflowing cool air and inner room air are 10, 20, $30^{\circ}C$, and the inlet velocities of inflowing cool air are 1, 2, 3m/s respectively as dynamic parameters. Also, a anemos and a vane type diffuser are used as inlet geometric conditions. Following conclusions have been obtained through this study. 1) In case of the anemos type diffuser, it is found that a dimensionless temperature profile is low and the distribution of the inflowed cool air is uniform. and also, all diffuusers have a low temperature of the inner room as increasing the inlet velocity. 2) A mixing takes place rapidly in case of the anemos type diffuser when the temperature difference is low ${\Delta}T=10^{\circ}C$ and the inletvelocity is high V=3m/s. and the mixing degree is higher with the anemos type diffuser than the vane.