• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.1792-1798
• /
• 1991

본 연구에서는 균열 끝을 포함하는 선 적분을 행하여 $J_{k}$ 구한 다음 이방 성 재료에서의 탄성계수 상호간의 관계를 이용하여 $J_{k}$를 탄성계수와 응력확대계 수 $K_{I}$, $K_{II}$ 로 간단히 표현 하고자 한다. 이 결과는 선형탄성 이방성 재 료에서 수치적으로 응력확대계수를 구하는 데 있어 기초 자료로 활용 될 것으로 생각 된다.다.다.다.

• 대한기계학회논문집A
• /
• 제32권5호
• /
• pp.411-418
• /
• 2008

In this work, the effect of strength mismatch on plastic limit loads is quantified for similar metal weld plates with cracks under tension load, via three-dimensional, small strain elastic-perfectly plastic finite element analyses. Relevant variables related to plate geometry and crack length are systematically varied, in addition to the weld width. An important finding is that mis-match limit loads can be uniquely quantified through strength mis-match ratio and one geometry-related parameter. Based on the proposed limit load solutions, reference stress based J-integral estimates is also investigated. When the reference stress is defined by the mis-match limit load, predicted J-integral values agree overall well with FE results.

• 오토저널
• /
• 제12권1호
• /
• pp.26-32
• /
• 1990

This study investigated a method for the determination of the J-integral for a tough glassy polymer such as polycarbonate plates by using the method of caustics. Comparing the values of J-integral determined by a numerical analysis and by the method of caustics, the method of caustics was found to be an effective experimental technique for the determination of the J-integral. The ratio between two J-integrals determined by the method of caustics and by finite element method converged into 1 within the limit of low load. However, it was noticed that the greater the plastic zone at the crack tip was, the lower the J-integral obtained by the reflect method of caustics. This difference may be deduced from the damage at the crack tip such as craze appeared in the polycarbonate plate. It was confirmed that the ratio of longitudinal diameter( $D_{l}$ ) to transverse diameter ( $D_{t}$) of caustics generally converged into 1 at the low load. The transition of the state of stress at the vicinity of a crack tip from plane strain to plane stress was deduced by noticing that the longitudinal diameter( $D_{l}$ ) grew faster than the transverse diameter( $D_{t}$) of caustics within the higher load range.

• Journal of Mechanical Science and Technology
• /
• 제17권2호
• /
• pp.254-268
• /
• 2003

The explicit formulation of the J-integral and the M-integral is constructed in terms of the stress intensity factor and the higher order stress coefficients for Mode II cracks under small or large scale yielding. Furthermore, the stress intensity factor and the higher order stress coefficients as well are computed with the aid of the two-state J- and the M-integral, which is found to be accurate and efficient. It is found that the contribution from the higher order singularities to the J-integral is closely related to the configuration of the plastic zone.

• 대한기계학회논문집
• /
• 제18권8호
• /
• pp.2158-2166
• /
• 1994

In order to understand the package crack emanating from the edge of leadframe after the delamination between leadframe and epoxy molding compound in an electronic packaging of surface mounting type, the M-integral and J-integral in fracture mechanics are obtained. The effects of geometry, material properties and molding process temperature on the package crack are investigated taking into account the temperature dependence of the material properties, which simulates a more realistic condition. If the temperature dependence of the material properties is considered the result of analysis conforms with observations that the crack is kinked at between 50 and 65 degree. However, in case of constant material properties at the room temperature it is found that the J-integral is underestimated and the kink crack angle is different form the observation. The effects of the material properties and molding process temperature on J-integral and crack angle are less significant that the chip size for the cases considered here. It is suggested that the geometric factors such as ship size, leadframe size are to be well designed in order to prevent(or control) the occurrence and propagation of the package crack.

• 한국압력기기공학회 논문집
• /
• 제16권2호
• /
• pp.35-46
• /
• 2020

In this paper, a fracture mechanics evaluation system which can be used to assess the leak-before-break (LBB) of nuclear piping is developed. Existing solutions for calculating the fracture mechanics parameters (J-integral and crack opening displacement) required for LBB evaluation were firstly presented. Then a module for calculating J-integral and COD was developed, with an additional module for predicting the critical load based on the crack driving force diagram to finally develop a fracture mechanics evaluation system. To confirm the validity of the proposed evaluation system, finite element (FE) analysis was performed, and the FE J-integral and COD results were compared with prediction results using the J-integral and COD estimations program. Furthermore, the critical load assessment module was verified by comparing the actual pipe test results (Battelle test data) with prediction results using the proposed program.

• 대한기계학회논문집
• /
• 제10권6호
• /
• pp.937-946
• /
• 1986

본 논문에서는 이와 같은 점을 고려하여 두께가 얇은 평면응력 상태의 CT 시 험편을 이용하여 W와 z의 변화에 따른 파괴인성치와 J저항곡선의 거동 및 크랙성장을 고려한 J적분식도 검토하였다. 또한, 재료를 변형경화 재료로 가정하고 HRR 응력변 형율장의 특성을 이용하여 컴퓨터 프로그램을 작성하여 J적분을 구한 후 실험치와 상 호 비교 검토하였다. 이 때 사용한 입력자료는 실험치의 그것과 동일하게 하였다.

• 대한기계학회논문집A
• /
• 제26권1호
• /
• pp.105-112
• /
• 2002

In recent years, the integrity of reactor Pressure Vessel(RPV) under pressurized thermal shock (PTS) accident has been treated as one of the most critical issues. Under PTS condition, the combination of thermal and mechanical stress by steep temperature gradient and internal pressure causes considerably high tensile stress at the inside of RPV wall. As a result, cracks on inner surface of RPV may experience elastic-plastic behavior which can be characterized by J-integral. In such a case, however, J-integral may possibly lose its vapidity due to the constraint effect. The degree of constraint effect is influenced by the loading mode, crack geometry and material properties. In this paper, in order to investigate the effect of clad thickness and crack geometry on constraint effect, three dimensional finite element analyses were performed for various surface cracks. Total of 27 crack geometries were analyzed and results were presented by a two-parameter characterization based on the J-integral and the f-stress.

• Structural Engineering and Mechanics
• /
• 제3권6호
• /
• pp.541-553
• /
• 1995

The determination of the stress intensity factors is investigated by using the surface integral defined around the crack tip of the structure. In this work, the integral method is derived naturally from the standard path integral J. But the use of the surface integral is also extended to the case where body forces act. Computer program for obtaining the stress intensity factors $K_I$ and $K_{II}$ is developed, which prepares input variables from the result of the conventional finite element analysis. This paper provides a parabolic smooth curve function. By the use of the function and conventional element meshes in which the aspect ratio (element length at the crack tip/crack length) is about 25 percent, relatively accurate $K_I$ and K_{II}$ values can be obtained for the outer integral radius ranging from 1/3 to 1 of the crack length and for inner one zero.

• 대한기계학회논문집A
• /
• 제37권5호
• /
• pp.631-640
• /
• 2013

본 논문에서는 R6 코드와 RCC-MR A16 코드에서 원주방향 균열 배관에 대해 제시하는 1,2 차 복합 하중하에서 J-적분 계산법에 대한 정량적인 비교를 하였다. 균열의 형상, 균열의 깊이, 2 차 하중의 크기 변수에 대한 유한요소 해석을 수행 하였고 유한요소 해석 결과를 이용해 각 코드의 J-적분 평가법에 대한 정량적인 비교를 하였다. R6 코드는 $L_r=1$ 부근에서 보수적으로 평가 되었으며 RCC-MR A16 코드의 경우 기계하중이 작은 영역에서 보수적으로 평가되었다. 이와 같은 결과를 토대로 본 논문에서는 원주방향 균열이 있는 배관에 대하여 각 코드의 J-적분 계산을 보완할 수 있는 방법을 제시하였다. 그 결과로 보완된 J-적분 계산이 유한요소해석 결과와 잘 일치하는 것을 확인 하였다.