• 한국압력기기공학회 논문집
• /
• 제15권2호
• /
• pp.31-39
• /
• 2019

Cracked component analysis is needed for structural integrity analysis under seismic loading. Under large amplitude cyclic loading conditions, the change in material properties can be complex, depending on the magnitude of plastic strain. Therefore the cracked component analysis under cyclic loading should consider appropriate cyclic hardening model. This study introduces a procedure for determining an appropriate cyclic hardening model for cracked component analysis. The test material was nuclear-grade TP316 stainless steel. The material cyclic hardening was simulated using the Chaboche combined hardening model. The kinematic hardening model was determined from standard tensile test to cover the high and wide strain range. The isotropic hardening model was determined by simulating C(T) test under cyclic loading using ABAQUS debonding analysis. The suitability of the material hardening model was verified by comparing load-displacement curves of cyclic C(T) tests under different load ratios.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1992년도 춘계학술대회 논문집 92
• /
• pp.83-102
• /
• 1992

As shear localization is observed in different deformation modes, an attempt is made to understand the conditions for shear localization in general deformation modes. Most emphasis in put upon the effects of pre-localization deformation mode on the onset of shear localization and all the other well-recognized effects of subtle constitutive features and imperfection sensitivity studied elsewhere are not investigated here. Rather, an approximate perturbation stability analysis is performed for simplified isotropic rigid-plastic solids subjected to general mode of homogeneous deformation. Shear localization is possible in any deformation mode if the material has strain softening. The incipient rate of shear localization and shear plane orientations are strongly dependent upon the pre-localization deformation mode. Significant strain softening is necessary for shear localization in homogeneous axisymmetric deformation modes while infinitesimal strain softening is necessary for shear localization in plane strain deformation mode. In any deformation mode, there are more than one shear plane orientation. Except for homogeneous axisymmetric deformation modes, there are two possible shear plane orientations with respect to the principal directions of stretching. Some well-known examples are discussed in the light of the current analysis.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1996년도 추계학술대회논문집
• /
• pp.38-47
• /
• 1996

Sectional analysis program for plane strain or axisymmetric geometry of aluminum alloy sheet metals was developed. For modeling the anomalous behavior of aluminum alloy, Barlat's strain rate potential and Hill's 1990 non-quadratic yield theory arranged under the plane stress assumption were employed. 2-D rigid-viscoplastic FEM formulation based on the bending-augmented membrane theory was derived, solving simultaneously force equilibrium as well as non-penetration condition. Isotropic hardening law was also assumed for yielding behavior. To verify the validity and availability of the developed program, 2-D stretch/draw forming process for plane strain geometry and cylindrical cup deep drawing process for axisymmetric geometry were simulated.

• Structural Engineering and Mechanics
• /
• 제83권6호
• /
• pp.825-834
• /
• 2022

The effectiveness and accuracy of the strain-based approach applied for analysis of two kinds of heterogeneous hollow cylinders subjected to thermal and mechanical loads are examined in this study. One is a multilayer cylinder in which the material in each layer is assumed to be linearly elastic, homogeneous and isotropic. Another is a hollow cylinder made of functionally graded materials with arbitrary gradient. The steady state condition without heat generation is considered. A sector in-plane finite element in the polar coordinate system based on strain approach is used. This element has only three degrees of freedom at each corner node. Analytical solutions available in the literature are presented to illustrate the accuracy of the sector element used. The obtained results for displacements and stresses are shown to be in good agreement with the analytical solutions.

• 한국정밀공학회지
• /
• 제27권4호
• /
• pp.87-94
• /
• 2010

When occlusal force is applied to a tooth, stress concentration occurs on the dental cervical line. This study investigated to find the maximum force and strain of natural teeth using an Instron and strain gauges, comparing the strain of cervical enamel using finite element analysis(FEA). Tests were conducted with a mandibular first premolar applying the conditions of occlusion. Then, the FEA was processed with the same as conditions of the fracture test. The test showed that the maximum force, maximum compressive strain and maximum tensional strain was $278{\pm}26$ N, $0.668{\times}10^{-3}{\pm}0.678{\times}10^{-3}$ and $0.248{\times}10^{-3}{\pm}0.102{\times}10^{-3}$, respectively. It was found that six of eight measured strains were within the range of estimated strains by the FEA. Even though it was assumed that properties of FE models were isotropic, it could prove useful as a reference in understanding the tendency of dental strain.

• Composites Research
• /
• 제30권3호
• /
• pp.193-201
• /
• 2017

탄소나노튜브와 폴리에스터 계면 간 그래프팅이 나노복합재의 역학적 거동과 하중전달에 미치는 영향을 고찰하기 위해 분자동역학 전산모사를 수행하고 그 결과를 Mori-Tanaka 모델 예측해와 비교하였다. 각 방향으로의 인장과 전단 전산모사를 통해 응력-변형률 선도를 도출한 후, 가교 유무에 따른 탄성거동 변화를 관찰하였다. 또한 가로등방성 강성행렬을 방향 평균하여 나노튜브가 랜덤분포하는 경우의 등방성 영률과 전단계수를 구하였다. 그 결과 가로방향 영률과 전단계수는 그래프팅 가공에 의해 향상되었으나, 길이방향 영률의 경우 나노튜브의 물성감소로 인해 오히려 물성이 저하되었다. 나노튜브의 랜덤분포를 고려한 예측 결과에서는 그래프팅 가공에 의해 물성이 약간 감소하였다.

• Advances in materials Research
• /
• 제6권2호
• /
• pp.155-168
• /
• 2017

The terrorist attacks and dangers by bomb blast have turned into an emerging issue throughout the world and the protection of the people and structures against terrorist acts depends on the prediction of the response of structures under blast and shock load. In this paper, behavior of aluminum and unidirectionally reinforced E-Glass Epoxy composite plates with and without focal circular holes subjected to shock loading has been identified. For isotropic and orthotropic plates (with and without holes) the classical normal mode approach has been utilized as a part of the processing of theoretical results. To obtain the accurate results, convergence of the results was considered and a number of modes were selected for plate with and without hole individually. Using a shock tube as a loading device, tests have been conducted to composite plates to verify the theoretical results. Moreover, peak dynamic strains, investigated by experiments are also compared with the theoretical values and deviation of the results are discussed accordingly. The strain-time histories are likewise indicated for a specific gauge area for aluminum and composite plates. Comparison of dynamic-amplification factors between the isotropic and the orthotropic plates with and without hole has been discussed.

• Structural Engineering and Mechanics
• /
• 제44권6호
• /
• pp.753-762
• /
• 2012

The ratcheting characteristics of cylindrical shell under cyclic axial loading are investigated. The specimens are subjected to stress-controlled cycling with non-zero mean stress, which causes the accumulation of plastic strain or ratcheting behavior in continuous cycles. Also, cylindrical shell shows softening behavior under symmetric axial strain-controlled loading and due to the localized buckling, which occurs in the compressive stress-strain curve of the shell; it has more residual plastic strain in comparison to the tensile stress-strain hysteresis curve. The numerical analysis was carried out by ABAQUS software using hardening models. The nonlinear isotropic/kinematic hardening model accurately simulates the ratcheting behavior of shell. Although hardening models are incapable of simulating the softening behavior of the shell, this model analyzes the softening behavior well. Moreover, the model calculates the residual plastic strain close to the experimental data. Experimental tests were performed using an INSTRON 8802 servo-hydraulic machine. Simulations show good agreement between numerical and experimental results. The results reveal that the rate of plastic strain accumulation increases for the first few cycles and then reduces in the subsequent cycles. This reduction is more rapid for numerical results in comparison to experiments.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제33회 KOSCO SYMPOSIUM 논문집
• /
• pp.177-186
• /
• 2006

Flame surface area is a critical parameter determining turbulent flame speed. Three-dimensionaldirect numerical simulations (DNS) were conducted to figure out the evolution process of flame surface area. Fully compressible Navier-Stokes equations are solved to reproduce premixed flame embedded in isotropic decaying turbulent flow. The tangential straining and curvature of propagating surface affect development of flame area. In this study, four different turbulent intensity flows and three different Le number flames are investigated to force changes in straining and curvature effects. Consistent results are obtained for the probability density functions (PDF) of strain and curvature with previous researches. It is revealed that displacement speed, which is a speed of flame surface relative to unburnt flow, controls the balance between sink and source of flame surface area.

• 한국연소학회지
• /
• 제12권2호
• /
• pp.10-19
• /
• 2007

Flame surface area is a critical parameter determining turbulent flame speed. Three-dimensional direct numerical simulations(DNS) were conducted to figure out the evolution process of flame surface area. Fully compressible Navier-Stokes equations are solved to reproduce premixed flame embedded in isotropic decaying turbulent flow. The tangential straining and curvature of propagating surface affect development of flame area. In this study, four different turbulent intensity flows and three different Le number flames are investigated to force changes in straining and curvature effects. Consistent results are obtained for the probability density functions (PDF) of strain and curvature with previous researches. It is revealed that displacement speed, which is a speed of flame surface relative to unburnt flow, controls the balance between sink and source of flame surface area.