• Earthquakes and Structures
• /
• v.3 no.2
• /
• pp.169-180
• /
• 2012

The performance of pure friction isolation system with respect to the frequency bandwidth of excitation and the predominant frequency is investigated. A set of earthquake ground motions (artificial as well as recorded [with different combinations of magnitude-distance and local site geology]) is considered for investigating effectiveness of pure friction isolators. The results indicate the performance of pure friction base isolated system does not only depend upon coefficient of friction and mass ratio but the stick-slip behaviour depends upon the frequency content of the excitation as well. Slippage prevails if the excitation frequency lies in a suitable frequency range. This range widens with increasing mass ratio. For larger mass ratios, the sliding effect is more pronounced and the maximum acceleration response is further reduced in the neighbourhood of frequency ratio (${\omega}/{\omega}_n$) of unity. The pure friction isolation system is effective in the case of broadband excitations only and that too, in the acceleration sensitive range of periods. The pure friction system is not effective for protection against narrow band motions for which the system response is quasi-periodic.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.11
• /
• pp.1066-1074
• /
• 2004

A vibration isolation system for a large reverberation chamber (1,228 $m^3$ and 1,000 ton) has been installed and verified. The reverberation chamber generates loud noise and induces high level of vibration while performing spacecraft acoustic reliability tests. The isolation system prevents vibration transfer from the chamber to the enclosure buildings. This paper describes design process and commissioning experiments of the system. Design criteria have been derived from rigid body model of the chamber. The stiffness of neoprene pads has been selected by employing finite element analysis of the reverberant chamber and isolation system. A total of 21 neoprene pads have been installed between the chamber and supporting Pedestals. A sand bag of 800kg was dropped on the chamber floor to measure the natural frequency of the isolation system. While 136.9 dB noise is generated in the chamber, absolute transmissibility of the isolation system has been measured. The measured natural frequency of the chamber is 10.2Hz, which is 80% of the predicted value. Overall transmissibility at working frequency range (25∼10.000 Hz) is less than -12.4 dB.

• Journal of Power Electronics
• /
• v.2 no.2
• /
• pp.112-123
• /
• 2002

This paper presents a novel prototype of the utility AC power interfaced soft-switching sinewave pulse modulated inverter using the high-frequency flyback for the small scale distributed renewable energy power conditioner. The proposed cricuit with a high-frequency isolation link has a funtion of electrical isolation, which is more cost-effective and reliable for the small-scale distributed renwal energy utilization system from a safety point of riew. The discontinuous conduction mode(DCM) operation of the high-frequency flyback transformer is adopted to establish a simple and low-cost circuit configuration and control scheme. For the simplicity, the circuit operating principle is described on the basis of the modified conventional full bridge inverter, whitch is the typical conventional high-frequency full-bridge inverter employing the high requency flyback transformer to eanble the effictive function of the electrical isolation. Than, the new circuit topology of the unility-interfaced soft-switching sinewave pulse modulated inverter using IGBTs is proposed. The proposed cricuit topology is additionally composed of the auxiliary power regenerating snubber cricuits, which are also mathematically analyzed for the parameter desigen settings. Finally, the performance of the propose inverter is evaluated on the basis of computer-aid simulation. It is noted that the sinewave pulse modulated output current of the inverter is synchronous to the AC main voltage.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.921-924
• /
• 2005

We report low conversion loss and high LO to RF isolation 94 GHz MMIC resistive mixers based on 0.1 ${\mu}m$ InGaAs/InAlAs/GaAs metamorphic HEMT technology. The fabricated resistive mixers applied a one-stage amplifier on RF port of the mixer. By using the one-stage amplifier, we obtained the decrement of conversion loss and the increment of LO to RF isolation. So, we can obtain higher performances than conventional resistive mixers. The modified mixer shows excellent conversion loss of 6.7 dB at a LO power of 10 dBm. We also observed an extremely high isolation characteristic from the MMICs exhibiting the LO-RF isolation of 21 ${\pm}$ 0.5dB in a frequency range of 93.7${\sim}$ 94.3 GHz. The low conversion loss and high LO-RF isolation characteristics of the MMIC modified resistive mixers are mainly attributed to the performance of the MHEMTs exhibiting a maximum transconductance of 654 mS/mm, a current gain cut-off frequency of 173 GHz and a maximum oscillation frequency of 271 GHz.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.275-278
• /
• 2005

In this study, the dynamic properties of a floor impact sound isolation pad expressed in terms of the natural frequency, the dynamic stiffness per unit area and the loss factor are measured by the resonant method. By using the measured dynamic properties, the vibration transmissibility diagram is obtained for each isolation pad, which is compared with the values tested by the impact sound sources at the room in an apartment. From the comparative results, it is found that the noise reduction Performances. of isolation pads are closely connected with the natural frequency and the dynamic stiffness per unit area.

• Journal of electromagnetic engineering and science
• /
• v.16 no.4
• /
• pp.206-209
• /
• 2016

This letter proposes a reconfigurable directional coupler that uses a variable impedance mismatch reflector to achieve high isolation characteristics in the antenna front end. The reconfigurable coupler consists of a directional coupler and a single-pole four-throw (SP4T) switch with different load impedances as a variable load mismatch reflector. Selection of the load impedance by the reflector allows cancellation of the reflected signal due to antenna load mismatch and the leakage from the input to isolation port of the directional coupler, resulting in high isolation characteristics. The performance of the proposed architecture in separating the received (Rx) signal from the transmitted (Tx) signal in the antenna front end was verified by implementing and testing the reconfigurable coupler at 917 MHz for UHF radio-frequency identification (RFID) applications. The proposed reconfigurable directional coupler showed an improvement in the isolation characteristics of more than 20 dB at the operation frequency band.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.6
• /
• pp.1014-1023
• /
• 2015

This paper presents the method of antenna polarization isolation and resource control for frequency interference reduction due to the frequency reuse between opposite sectors. We have examined the frequency interference between opposite sectors which is occurred by operating base station for reducing frequency interference. The base station has a frequency reusing structure in opposite sector. So, the base station can make a in-band frequency interference. In order to minimize frequency interference, we proposed two methods. The first is the antenna polarization isolation method. The CINR was improved to 27dB from 17dB when using the antenna polarization isolation. The second is resource control which is the method for lining up the RF power and limiting RF power control range of each link. In this paper, by using the proposed two methods, presents a scheme that reduces frequency interference in the frequency reusing structure.

• Korean Journal of Clinical Laboratory Science
• /
• v.39 no.2
• /
• pp.76-85
• /
• 2007

The total number of clinical materials collected from Dec 1, 2005 to Nov 30, 2006 in C. hospital was 63,133. Among these materials, the isolation of Staphylococcus spp. was 5,252 strains. The proportions of Staphylococcus species infection were as follows ; 46.7% in S. aureus, 39.3% in S. epidermidis, 4.7% in S. hominis, 3.8% in S. haemolyticus, 2.9% in S. capitis and 2.5% in others. Seventeen strains of Staphylococcus species were identified with an isolation range of 0.02-46.7%. The isolation ratios of Staphylococcus species were 7.8% (2,134/27,362) in female, 8.7% (3,118/35,807) in male and 8.3% (5,252/63,133) in both. The age-related frequencies of Staphylococcus species were 22.1% in the 60-69 year group, 19.3% in the 70-79 year group and 17.1% in the 50-59 year group. The isolation ratio of the 0-49 year group to the 50-over 80 year group were 1.74 times in female, 1.92 in male and 1.85 in both. The isolation frequency of Staphylococcus spp. was at its highest in April (9.9%) and at its lowest in February (6.8%) according to monthly analysis. According to seasonal variation, the isolation frequencies of Staphylococcus spp. were 27.0% in Summer, 25.9% in Spring, 23.9% in Fall and 23.2% in Winter. The clinical departments showing over 9% isolation rate against Staphylococcus spp. were critical care medicine (12.9%), department of pediatrics (11.6%), department of urology (9.8%) and department of neuro-surgery (9.1%). On the other hand, the lowest number was observed in the department of family medicine. The clinical material showing over 15% isolation rate against Staphylococcus spp. were 32.1% in urine (random urine and catheterized urine), 20.6% in blood and 16.0% in sputum.

• Earthquakes and Structures
• /
• v.4 no.4
• /
• pp.341-363
• /
• 2013

Earthquake response calculation, parametric analysis and seismic parameter optimization of base-isolated structures are some critical issues for seismic design of base-isolated structures. To calculate the earthquake responses for such non-symmetric and non-classical damping linear systems and to implement the earthquake resistant design codes, a modified complex mode superposition design response spectrum method is put forward. Furthermore, to do parameter optimization for base-isolation structures, a graphical approach is proposed by analyzing the relationship between the base shear ratio of a seismic base-isolation floor to non-seismic base-isolation one and frequency ratio-damping ratio, as well as the relationship between the seismic base-isolation floor displacement and frequency ratio-damping ratio. In addition, the influences of mode number and site classification on the seismic base-isolation structure and corresponding optimum parameters are investigated. It is demonstrated that the modified complex mode superposition design response spectrum method is more precise and more convenient to engineering applications for utilizing the damping reduction factors and the design response spectrum, and the proposed graphical approach for parameter optimization of seismic base-isolation structures is compendious and feasible.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.401-406
• /
• 2013

This paper presents experimental evaluation of IRE (isolation roller bearing) seismic isolation device. From the combination of base isolation on the IRE system displacement response spectrum and acceleration response spectrum, the compressive strength and the coefficient of friction experiments. Also the IRE system is evaluated by environment test according to KS standards. Both the resonance and seismic experiments using a combination of the IRE and Natural Rubber Bearing (NRB) are performed in order to analyze the seismic isolation of the IRE system dynamic characteristics. For the given load and exciting frequency, the resonant frequency becomes lower, but the resonant magnification remains to be same. However, it is shown that when we consider the IRE only, the vibration on the table with the horizontal movement and the independent horizontal displacement due to the rolling motion of the plate and roller are significantly reduced. This result verifies that the proposed optimal design method of the IRE system is very effective.