• Transactions of Materials Processing
• /
• v.12 no.4
• /
• pp.302-307
• /
• 2003

Hot rolled strip is cooled by air and water in Run-Out-Table. In this process, phase transformation and shape deformation occurs due to temperature drop. Because of un-ideal cooling condition of ROT, irregular shape deformation and phase transformation arise in the strip. which affect the strip property and lead to the residual stress of strip. And these exert effects on the following processes, coiling process, coil cooling process, and re-coiling process. Through these processes, the residual stress becomes higher and severe. For the prediction of residual stress distribution and shape deformation of final product, Finite element(FE) based model was used. It consists of non-steady state heat transfer analysis, elasto-plastic analysis. thermodynamic analysis and phase transformation kinetics. Successive FEM simulation were applied from ROT process to coil cooling process. In each process simulation, previous process simulation results were used for the next process simulation. The simulation results were matched well with the experimental results.

• Journal of the Korean Ceramic Society
• /
• v.27 no.6
• /
• pp.729-734
• /
• 1990

The microstructural dependence of thermal conductivity of a high-alumina (ca. 70%) heat-insulating frebricks(ca. 75%porosity) was investigated under special consideration of the tailored-pore shape effects. Pores different shape could be incorporated into the insulators through pore formers : Styrofoam produces spherical pores while saw dust results in parallel plate pores. Concerning the pore-shape effectiveness of thermal insulation, the specimen with irregular plate pores showed much lower values of heat conductivity than those with spherical pores, the values being 0.31 to 0.38 at $600^{\circ}C$ and 0.35 to 0.47 at 100$0^{\circ}C$, respectively. On the contrary, however, other material properties such as strength and softening temeprature under load were turned out to be better in the case of the spherical pores.

• Proceedings of the KWS Conference
• /
• 2000.10a
• /
• pp.216-218
• /
• 2000

In case of hardfaced wrapping roll, beadmark shape appear at wrapping roll surface due to irregular wear between weld bead. Irregular wear of this is caused by difference of hardness between weld bead. This study aims at investigating which matrix is good for removing of beadmark at wrapping roll surface. So, we make specimen with martensitic matrix and austenitic matrix. The hardfacing alloys were deposited 4 times on a SS41 steel plate using self-shielding flux cored arc welding method. Difference of hardness between weld bead of specimen with matrix of martensite was higher than specimen with matrix of austenite both as-welded and after heat treatment. Therefore, austenitic matrix is better than martensitic matrix for removing of beadmark of wrapping roll surface.

• Journal of Industrial Technology
• /
• v.24 no.A
• /
• pp.139-155
• /
• 2004

A room and pillar mining method has been adopting at the Jeungsun limestone mine. To check stability of pillar with multiple and irregular openings, the size, shape and spacing of rib pillar were first designed using some empirical suggestions. The Finite Difference Method(FDM)was used to analyze the pillar stability. Twelve different cases with the variation of K(horizontal/vertical stress)values, different height and different spacing of pillar were used in this study. Finally Mohr-Coulomb criterion was adopted to calculate the safety factors. Horizontal and vertical displacement, maximum and minimum principal stresses, range of plastic zone and safety factors were calculated at each case. As a result of analysis, the size of one block is 160m long, 70m wide, 40m high with 20m wide rib pillar and 20m square column pillar. The overall recovery at this case can be estimated about 40%.

• Journal of Mechanical Science and Technology
• /
• v.17 no.7
• /
• pp.986-998
• /
• 2003

In this paper, an adaptive numerical integration scheme, which does not need non-overlapping and contiguous integration meshes, is proposed for the MLPG (Meshless Local Petrov-Galerkin) method. In the proposed algorithm, the integration points are located between the neighboring nodes to properly consider the irregular nodal distribution, and the nodal points are also included as integration points. For numerical integration without well-defined meshes, the Shepard shape function is adopted to approximate the integrand in the local symmetric weak form, by the values of the integrand at the integration points. This procedure makes it possible to integrate the local symmetric weak form without any integration meshes (non-overlapping and contiguous integration domains). The convergence tests are performed, to investigate the present scheme and several numerical examples are analyzed by using the proposed scheme.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.8
• /
• pp.1854-1868
• /
• 1995

An effective nesting algorithm has been proposed to allocate the arbitrary shapes on one or several raw sheets by applying the well-known simulated annealing algorithm as the optimization technique. In this approach, both the shapes to be allocated and the raw sheets are represented as the grid-based models. This algorithm can accommodate every possible situations encountered in cutting apparel parts from the raw leather sheets. In other words, the usage of the internal hole of a shape for other small shapes, handling of the irregular boundaries and the interior defects of the raw sheets, and the simultaneous allocation on more than one raw sheets have been tackled on successfully in this study. Several computational experiments are presented to verify the robustness of the proposed algorithm.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.521-527
• /
• 1997

Irregular shapes and growth behavior of surface micro-crack showed very complex and nonlinear propeties and many investigators have performed theoretical analysesand experiments on them to characterize fatigue strength. They had difficulties in estimating fatigue life due to random distribution, growth and coalescence of surface micro-cracks. The straightness of crack growth along intergranular and transgranular was prevented from irregular microstructure and precipitates. Euclid geometry can't quantify shape of surface micro-crack but ftractal geometry can. Therefore, it is suggested that average fractal dimension of surface micro-cracks is able to estimate fatigue life but fractal dimension of maximum surface micro-crack is not in Al 2024-T3 alloy.

• Journal of Welding and Joining
• /
• v.18 no.6
• /
• pp.68-73
• /
• 2000

In case of overalyered wrapping roll, beadmark shape appear at wrapping roll surface due to irregular wear between weld bead. Irregular wear of this is caused by difference of hardness between weld bead. This study aims at investigating which matrix is good for removing of beadmark at wrapping roll surface. So, we make specimen with martensitic matrix and austenitic matrix. The overlayered alloys were deposited 4 times on a SS41 steel plate using self-shielding flux cored arc welding method. Difference of hardness between weld bead of specimen with matrix of martensite was higher than specimen with matrix of austenite both as-welded and after heat treatment. Therefore, austenitic matrix is between than martensitic matrix for removing of beadmark of wrapping roll surface.

• Restorative Dentistry and Endodontics
• /
• v.12 no.2
• /
• pp.91-98
• /
• 1987

This study was designed to investigate the changing depositional pattern of inorganic enamel substances during enamel formation and maturation. For this purpose, white rat incisors which continuously grow and develop during the life, were chosen as specimens. And after treated with 20% KOH solution, outer surface of forming inorganic enamel were observed with the scanning electron microscope, dividing into 6 types according to the forming pattern from apical to cuspal direction. The observations lead to the following conclusions: 1. During the initial enamel forming stage, inorganic enamel substances were deposited with very irregular pyramidal shape on the root dentin surface. 2. During the enamel forming stage, inorganic enamel substances were deposited with relatively regular hexagonal, honey-comb appearance. 3. During the later enamel forming stage, inorganic enamel substances were deposited with very irregular and roughly amorphous appearance. 4. During the later enamel maturating stage, very small and round inorganic enamel substances were deposited densely, and made a flat enamel surface.

• Journal of the Korean Academy of Esthetic Dentistry
• /
• v.7 no.1
• /
• pp.64-70
• /
• 1998

Recently as the interest on Esthetic Dental Prosthesis is arising, the domains of Esthetic Dentistry is being widely investigated. Esthetic Dental Prosthesis is influenced greatly by the shape, color, tooth arrangement of the teeth and the facial features(including the lips). So the degree to which these characters harmonize will be the professional esthetical standard while the satisfaction of the patient will be another esthetical measure. The reason for this is that each and every one of us has a different standard of what is considered beautiful. Of course it doesn't mean that every standard is correct. Then what does Esthetical Prosthesis mean and what should the standard be? This must be defined as a prosthesis that satisfies the basic requirements - margin, contour, occlusion, and at the same time it should restore the shape, color, and tooth arrangement which the client(patient) would love to have. As Esthetic Prosthesis contains its subjective meaning a great deal, it shouldn't be simply distinguished between the beauty of the teeth itself or ugliness. Also in some case, it needs surgical treatment to make it harmonious in the whole aspect so that one may keep the feeling of satisfaction and security. Then what is the shape, color, tooth arrangement that each individual wants? There is an indefinite variety. For example, considering arrangement both regular and irregular is considered beautiful by each different individual. Regular arrangement may be the standard of beauty for some, while irregular arrangement may be thought of as natural looking and beautiful. That is why there must be enough communication with the patient and an agreement be made at the clinic before a diagnostic plan and actual surgery. The treatment plan as mentioned above must be sent to the dental laboratory. In this research, by using case studies, I am going to the importance and appropriateness of the data and information for the dental technician's esthetic prosthesis.