• Journal of environmental and Sanitary engineering
• /
• v.17 no.1
• /
• pp.57-62
• /
• 2002

Carbon cast iron and Zinc coated steel were the most widely used portable water of supply and distribution Pipeline system. The leaching of red water in portable water could produce sericus environmental sanitary problems. Due to the red water was the most alternative to inner scale of metal pipeline. So this study was conducted the impact of red water on scale products, and was evaluated by the corrosive metal contaminants of 20 fears over. Surface tests, metal surface composition measurements of samples XRF, XRD, and SEM(EDS), analysis were used to investigate the corrosion characteristies of carbon cast iron and Zinc coated steel. As the contaminants of Fe increased the red water of carbon castiron pipe increased due to the scale products amount of $Fe_2O_3$ (Hemite).

• Journal of Surface Science and Engineering
• /
• v.32 no.4
• /
• pp.538-546
• /
• 1999

Ti(IV)-Fe(III) oxide films were formed by MOCVD technique, and their photoelectrochemical properties were examined in 0.5M N $a_2$$SO_4$ solution by a photoelectrochemical polarization test. Ti(IV)-Fe(III) oxide films deposited at 40$0^{\circ}C$ by MOCVD have crystalline structure and are all n-type semiconductors. The photocurrent and the quantum efficiency of the films increase with increasing the iron cationic fraction ($X_{Fe}$ ) in the films. The energy band gap of the films increase linearly with increasing the iron cationic fraction in the films. Ti(IV)-Fe(III) oxide film of $X_{Fe}$ /=0.60 has high photocurrent response and corrosion resistance simultaneously.

• Journal of Korea Foundry Society
• /
• v.13 no.5
• /
• pp.476-483
• /
• 1993

The influence of substrate materials on the degree of basal porosity during spray casting process has been investigated. Different conditions of droplet spreading on the substrate were induced by varying the substrate material. Flat sections of cast iron and aluminum have been spray deposited via spray casting process onto an aluminum substrate, a low carbon steel substrate, and an alumina based refractory substrate. Results for cast iron and aluminum sprayed onto the aluminum substrate showed significant improvements in the surface condition and degree of basal porosity with evidence of substrate deformation that round pits ranging from $5{\mu}m$ to $20{\mu}m$ in diameter are distributed on the surface of aluminum substrate. The lowest level of porosity was developed in alumina based refractory material. Several mechanisms for porosity formation were discussed with droplet impact pressure and droplet spreading. Adopting a spray cutting mechanism for removing the periphery of spray cone, porosity level was remarkably decreased.

• Journal of Surface Science and Engineering
• /
• v.26 no.2
• /
• pp.82-86
• /
• 1993

An attempt was made to reduce directly Nd2O3 in a cryolited based fluoride bath. Neodymium metal was electrodeposited on the iron cathode to produce the Fe-Nd eutectic alloy in a liquid state at 90$0^{\circ}C$. Graphite was adopted for the anode and pure iron for the cathode. Electrolyte was composed of Na3AlF6 50wt.%. AlF3 34wt.% and Nd2O3 16wt.%. Analysis of typical alloy product showed Al 63.4wt.% Fe 26.9wt.% and Nd 7.0 wt.% The enrichment of neodymium in the alloy couldn't be obtained because aluminum codeposited with ne-odydmium. Experimental results proved that the cryolited based electrolyte was unstable for the electrolysis of rare earth oxides even though their prominent solubilities.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.63-64
• /
• 2011

니켈 알러지를 일으키지 않는 전주 부품 개발을 위해 Ni을 대체할 수 있는 전주 소재로 Ni-Fe 합금과 Fe에 대한 전주 공정을 개발하였다. Ni-Fe 합금 전주의 경우 전주품의 표면 내식성 강화를 위해 Cr 나노입자를 이용한 복합전주를 실시하여, Ni 전주품과 내부식성, 니켈 용출 비교 분석 실험을 하였다. 또한 Ni을 완전히 배제하기 위해 새로운 시도로서 순 Fe 전주 공정 기술을 개발하였다. 제조된 Fe 전주품의 내식성 향상을 위한 실리카 코팅 등의 표면처리에 대한 효과도 분석하였다.

• 보존과학연구
• /
• s.19
• /
• pp.179-191
• /
• 1998

The Dumu of casted iron objects which is the big vessel for the prevention of fire to wood building is conserved in Kyongpok Palace(Dumu sizes：diameter 97cm, height 42cm, thickness 2cm, weight 250kg). The treated objects which some parts were lost, were not corroded, but cracted and broken by an external power, and strongly attached an cement layer on inside surface. First of all cement layer was mechanically removed by pneumatic needle scaler, welded to electric method for broken and cracked pieces, and then the lost sections were restored to use a epoxy resin and glass fiber. In order to prevent a damage during the handling, the restoration section of the inside surface was treated different colour in comparison with original part.

• Journal of Surface Science and Engineering
• /
• v.32 no.1
• /
• pp.21-30
• /
• 1999

Coating adherance behavior of low carbon steels, produced by POSCO, Korea, was studied in order to study the characteristics of hot rolled galvanized iron(HGI) manufactured without pickling line and the development of its process. Galvanizing experiments were carried out in zinc pot with 0.2wt% Al after hot rolled plates with scale were reduced at $550~750^{\circ}C$ in 10~30% hydrogen gas atmosphere during 60~400seconds. The reduced plates and coated products were examined by SST, XRD, SEM and EPMA on their surfaces and cross sections. Coating layer of HGI manufactured with pickling line was composed of retained scale, Fe-Zn-Al compound, Fe-Zn compound ($\delta_1\;and\;\zeta$ Phase) and pure zinc. It was superior to HGI in coating adhesion. It seems to be due to forming of Fe-Zn-Al compound in interface of matrix and retained porous scale.

• Journal of Surface Science and Engineering
• /
• v.33 no.4
• /
• pp.281-288
• /
• 2000

To understand the effect of Fe on the oxidation behavior of TiAl alloys, TiAl-(2, 4, 6at% )Fe were oxidized at 800 and 90$0^{\circ}C$ in air. The oxidation resistance of TiAl-Fe alloys increased with increasing an iron content. The scales formed consisted of an outer $TiO_2$ layer, an intermediate $A1_2$$O_3$ layer, and an inner mixed ($TiO_2$+$A1_2$$O_3$) layer, being similar to other common TiAl alloys. But, the scales formed on TiAl-Fe alloys were generally thin compared to those formed on pure TiAl, and contained dissolved iron. Below the oxide scale, an oxygen affected zone was formed. This beneficial effects of Fe on increasing the oxidation resistance and scale adherence of TiAl alloys were attributed to the refinement of oxide grains, increased scale adherence and the enhanced alumina-forming tendency.

• Journal of Surface Science and Engineering
• /
• v.32 no.1
• /
• pp.31-42
• /
• 1999

The effect was investigated that aluminium in the zinc bath has on the coating adhesion of Hot-rolled Galvanized Iron(HGI) manufactured without pickling process. It is thought that the coating adhesion of HGI manufactured without pickling process is good due to the fact that increasing aluminium content in the zinc bath makes zinc and aluminium diffuse to the cracks or pores in the scale formed through the reduction heat treatment, and Fe-Zn-Al compound with good ductility is formed in the scale layer and plays a role of anchor between zinc coating and substrate. It is possible that HGI with the good coating adhesion was produced without pickling treatment in the zinc bath with more that 3wt% of Al content even at the $550^{\circ}C$ of conventional reduction heating temperature. In creasing the temperature of heating section and aluminium content in the zinc bath prevents the Zn-Fe alloy. The corrosion resistance of HGI manufactured without pickling process is excellent because of the mixed reaction of zinc sacrifice and aluminium passivity film.

• Journal of Surface Science and Engineering
• /
• v.15 no.4
• /
• pp.218-225
• /
• 1982

The effects of ferrous ion on the properties of bright nickel electrodeposit were exa-mined. Iron exists as ferrous ion (Fe+2) and ferric ion (Fe+3) in the bath, a portion of the former tend to be oxidized to the somewhat harmful ferric ion. Iron was added to bath as the ferrous sulfate, ferrous ion prevented from the oxidation with citric acid. It was found that the hardness was increased as the concentration of ferrous ion, the ductility was slightly increased too. The appearance can obtain the wide bright deposits within 4g/$\ell$. The corrosion resistance drastically dropped from 5g/$\ell$ In the case of considering the effect of ferrous ion on the corrosion resistance and the appearance, the allowable limits is 4g/$\ell$, if the reductant is used.