• Resources Recycling
• /
• v.27 no.3
• /
• pp.30-38
• /
• 2018

In this study, the behaviors of Fe selective chlorination in ilmenite ore by using PVC or $CO-Cl_2$ gas mixture as reducing agents under the condition of 1173 K, for 60 minutes were investigated. The weight loss ratio was 28% when PVC was applied as the reducing agent. The condensate formed at the outlet of reaction tube was identified as $FeCl_2$ by X-ray diffraction analysis. From these results, it was observed that iron in ilmenite ore reacted with HCl gas and Fe was selectively removed in the form $FeCl_2$. However, when $CO-Cl_2$ gas mixture was used as a reducing agent, the weight reduction ratio was 54%, and the condensate formed at the outlet of reaction tube after the experiment was estimated to be $FeCl_3$. It was observed that the ilmenite ore reacted with the $CO-Cl_2$ gas mixture and was simultaneously removed in the form of $FeCl_3$ and $TiCl_4$. However, the results of X-ray diffraction of ilmenite ore after the reaction showed that Fe was almost removed.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.07a
• /
• pp.25-37
• /
• 2002

The most important industrial application of gamma radiation in characterizing green compacts is the determination of the density. Examples are given where this method is applied in manufacturing technical components in powder metallurgy. The requirements imposed by modern quality management systems and operation by the workforce in industrial production are described. The accuracy of measurement achieved with this method is demonstrated and a comparison is given with other test methods to measure the density. The advantages and limitations of gamma ray densitometry are outlined. The gamma ray densitometer measures the attenuation of gamma radiation penetrating the test parts (Fig. 1). As the capability of compacts to absorb this type of radiation depends on their density, the attenuation of gamma radiation can serve as a measure of the density. The volume of the part being tested is defined by the size of the aperture screeniing out the radiation. It is a channel with the cross section of the aperture whose length is the height of the test part. The intensity of the radiation identified by the detector is the quantity used to determine the material density. Gamma ray densitometry can equally be performed on green compacts as well as on sintered components. Neither special preparation of test parts nor skilled personnel is required to perform the measurement; neither liquids nor other harmful substances are involved. When parts are exhibiting local density variations, which is normally the case in powder compaction, sectional densities can be determined in different parts of the sample without cutting it into pieces. The test is non-destructive, i.e. the parts can still be used after the measurement and do not have to be scrapped. The measurement is controlled by a special PC based software. All results are available for further processing by in-house quality documentation and supervision of measurements. Tool setting for multi-level components can be much improved by using this test method. When a densitometer is installed on the press shop floor, it can be operated by the tool setter himself. Then he can return to the press and immediately implement the corrections. Transfer of sample parts to the lab for density testing can be eliminated and results for the correction of tool settings are more readily available. This helps to reduce the time required for tool setting and clearly improves the productivity of powder presses. The range of materials where this method can be successfully applied covers almost the entire periodic system of the elements. It reaches from the light elements such as graphite via light metals (AI, Mg, Li, Ti) and their alloys, ceramics ($AI_20_3$, SiC, Si_3N_4, $Zr0_2$, ...), magnetic materials (hard and soft ferrites, AlNiCo, Nd-Fe-B, ...), metals including iron and alloy steels, Cu, Ni and Co based alloys to refractory and heavy metals (W, Mo, ...) as well as hardmetals. The gamma radiation required for the measurement is generated by radioactive sources which are produced by nuclear technology. These nuclear materials are safely encapsulated in stainless steel capsules so that no radioactive material can escape from the protective shielding container. The gamma ray densitometer is subject to the strict regulations for the use of radioactive materials. The radiation shield is so effective that there is no elevation of the natural radiation level outside the instrument. Personal dosimetry by the operating personnel is not required. Even in case of malfunction, loss of power and incorrect operation, the escape of gamma radiation from the instrument is positively prevented.

• Journal of Bio-Environment Control
• /
• v.15 no.2
• /
• pp.177-183
• /
• 2006

The summer production of sweet pepper in Korea which cultured in the highland area such as Hapchon is essential for a year-round export, but has the problem, fruits lose easily those marketability. This study was carried out to find changes of fruit quality in response to storage on sweet pepper cultivars in summer. Seven cultivars of sweet peppers, 'Jubilee', 'Plenty', 'Goal', 'Romeca', 'Derby', 'Midas' and 'Maximalia' were obtained iron growers in Hapchon which was highland of 600-800m from sea level and stored at $10^{\circ}C$ with box packing. Fruit quality was evaluated every 4days up to 4weeks. The weight loss of 'Jubilee' was the lowest, that of 'Romeca' was the highest. The firmness of 'Goal' was maintained highly for 4weeks and the red cultivars was higher than those of other color cultivars. The lightness of 'Jubilee' was sensitively affected by storage duration. Seeds of 'Plenty' and 'Derby' were plentifully browned after 4weeks storage. The occurrence of fruit rotting was after 16-204ay storage and those of 'Plenty' and 'Maximalia' were the earliest. The marketability of 'Jubilee' and 'Romeca' maintained by 70% for 16 days was the highest, but most cultivars lost those by 20% after 24days storage. It may be suggested that the marketability of sweet pepper producted in summer can be stored at $10^{\circ}C$ for 2weeks to maintain that of 80%.

• Journal of Haehwa Medicine
• /
• v.13 no.2
• /
• pp.205-212
• /
• 2004

Now many sustitution and false articles is used in korea instead of heshouwu. To use heshouwu correctly, we will make a quilitative certificational plan of heshouwu to investigate all of lieraturea, records and documents. And we could reach conclusions as folloews. 1) Source of plant Heshouwu is a root tuber of a perennial herb Polygonum multiflorum Thunberg(Family : Polygonaceae). 2) Harvest After planting 3-5 yaers, harvesting in an autumn, washin clean the mud, a big heshouwu cut off a half or section, dry in sunny place or at a little fire. When harvesting, we harvest only a big thing, a small thing transfer a field, after culturing of 1-2 years, harvest at big roots. Harvesting is done usually in an autumn after 3 years. When collecting a seed, we must harvest a heshouwu the next year. 3) Process We must process heshouwu at the decoction of black beans, heshouwu suck in the decoction of black beans, heat with steam in an iron pot. Black beans is used every 100 kg of heshouwu. 4) Quility (1) Funstional standards It is good that weight is heavy and outer skin is yellow-brown, section surface is light red color, powdery and has a figure such as clouds in section. (2) Physicochemical standards Heshouwu expesses a various chang of components in process of working. We think that it need to add a standard of detection about 2,3,5,4'-tetrahrdroxystilbene-2-O-${\beta}$ -D-glucoside in a current authentic document which is a water-soluble component of heshouwu. It must that Dry on loss is less than 14.0%, content of ash is less than 5.0%, Content of acid-nonsoluble ash is less than 1.5%, Content of extract is more than 17.0%. A fixed quantity of 2,3,5,4'-tetrahrdroxystilbene-2-O-${\beta}$ -D-glucoside is more than 1.0%. Contens of heavy metal has to detect less than 30 ppm and there is no reminding agriculural medince.

• Journal of the Korean Chemical Society
• /
• v.10 no.1
• /
• pp.32-42
• /
• 1966

The electrolysis of tungstic oxide dissolved in the bath of calcium chloride and calcium oxide was studied to produce metallic tungsten using carbon as anode and iron as cathode in the temperature range of 900^{\circ}$ to $1200^{\circ}C$. The binary phase diagrams $CaCl_2$-CaO and $CaCl_2-CaWO_4$ systems were constructed to determine the suitability of bath composition and the range of temperatures for the electrolysis. As $WO_3$ reacted with $CaCl_2$ to form oxychloride in the fused salt, the addition of the proper amount of CaO was necessary to avoid the loss of $WO_3$. The optimum compositions of fused bath were $CaCl_2$ 100 parts, CaO and $WO_3$ each 10 to 20 parts, with the CaO, $WO_3$ ratio greater than unity, to keep freezing point low and to prevent the vaporization of $CaCl_2$. The observed decomposition voltage at which $WO_3$ decomposes to W and CO was-0.1 volt, whereas the calculated was -0.3 volt. Metallic tungsten deposited at the cathode reacted easily with CO formed secondarily at the anode surface, to form WC below $1050^{\circ}C$, so that the cell temperature should be above $1050^{\circ}C$. The effects of cathode current densities on current efficiency were minor in the range of 1 to 5 $amp/cm^2$.

• Journal of the Korean Chemical Society
• /
• v.19 no.3
• /
• pp.186-192
• /
• 1975

In the course of anthracite briquet combustion, air draft is usually controlled to continue burning of definite amount of briquet in the conventional hollow clay cylinder with air inlet hole open for given time, so that a large amount of CO tends to be produced. Therefore, it is necessary to establish an improved combustion process to depress the yielding rate of CO and for this purpose, we performed a basic experiment in which combustion rate of CO was measured in the mixture of $N_2, O_2 $and CO gas with or without the presence charcoal at the various temperature. The observed results showed that the burning temperature of CO is about 680${\sim}700^{\circ}C$, further burning rate of it was increased with increasing the amount of draft. From these facts, longer combustion time and low CO generation are thus contradictory to each other and it has been long desired to make those two compatible somehow. The purpose of the present investigation lies in designing an effective new briquet stove to meet the above requirements. The essential feature of the new briquet stove consisted in the use of two hollow iron cylinders with different inside diameter. A cylindrical air jacket thus formed served as a path through which small amount of secondary air run from the bottom of the stove to the upper vent holes. Heat exchange occurred between the upgoing secondary air and the burning briquet, which lowered the combustion temperature of the briquet. The results observed were selfevident as anticipated. It was confirmed that the combustion time was increased tolerably due to the heat loss from the combustion zone and that CO in the flue gas was reoxidized at the upper portion of the stove by the upgoing hot secondary air. By this reoxidation reaction the concentration of CO in the flue gas was found to be about 1/20 of that in case the conventional clay cylinder was used as briquet jacket.

• Journal of the Korean Institute of Navigation
• /
• v.10 no.2
• /
• pp.31-55
• /
• 1986

Generally, the development of shipping is characterized by the amount of traffic flow (traffic volume) and seaborne cargo in the sea. Movement of ships is an essential element of constructing the traffic flow which is represented the dynamic movement of ships in the sea, but on the other band the numbers of arriving and departing the port is the basic factor consisting of the static movement of ships. The amount of cargoes by coastal vessels and ocean trade vessels have increased tremendously with the great growth of the Korean economy these days. This increase of the seaborne cargoes has made the Korean coastal traffic flow so congested that this can be a cause of large pollution as well as great marine casualities such as a loss of human lives and properties . And also the future coastal traffic is expected to increase considerably according to our economic development and high dependence upon foreign trade. Under the circumstance, to devise the safety of coastal traffic flow and to take a proper step of a efficient navigation, there is a necessity for analyzing and surveying the coastal traffic trend and the characteristics of cargo movement. In order to grasp the dynamic movement of ships in the Korean coast, O/D analysis is executed. This paper aims to secure the basic data necessary for a comprehensive plan and estimation of vessel traffic management system for the enhancement of safety, order and efficiency of vessel traffic in the Korean coast. The analyzed results of the traffic flow and seaborne cargoes of the Korean coast are summarized as follows : 1) The congestion by the vessels occurred around the ports such as-in proportion of ship's number (proportion of tonnage) -Incheon 18.5%(14.8%), Pohang 5.9% (9.9%), Samil 5.2%(8.3%), Mokpo 8.6%(0.8%), Pusan 13.5%(36.4%), Ulsan 9.1%(16.2%). 2) It is found that the area adjacent to Incheon, Pusan, Ulsan, Channel of Hanryu and South-western area are heavily congested. 3) It is confirmed thatthe area adjacent to Incheon, Pusan, Ulsan, Channel of Hanryu and South-western area are heavily congested. 3) It is confirmed that the coastal vessels are main elements constituting the coastal traffic and that there are much traffic flow among five ports as following through the precise O/D analysis of ship's coastal movement. Incheon-Samil, Ulsan, Pusan, Jeju Pusan -Samil, Ulsan, Incheon, Jeju Pohang -Samil, Inchoen, Jeju Pohang -Samil, Incheon, Jeju Ulsan -Samil, Incheon, Jeju Samil -Ulsan, Pusan, Incheon 4) The amount of cargoes to abroad are in proportion about 81% of total and the amount of coastal cargoes are about 19%. Of those, cargoes in and out to Japan are about 26% and to South-east Asia are about 27%. 5) The chief items of foreign cargoes are oil(38.33%), iron ore(13.98%), bituminoous coal(12.74%), grain(8.02%), lumber(6.45%) in the import cargoes and steel material(21.96%), cement(17.16%), oil(6.81%), fertilizer(3.80%) in the export cargoes. 6) The 80.5% of total export cargoes and 92.4% of total import cargoes are flowed in five main ports. 7) The chief items of coastal cargoes are oil (42.45%), cement(16.86%), steel material (6.49%), anthracite(6.31%), mineral product(4.3%), grain, and fertilizer. Almost 92.24% of total import and export oil cargoes in Korea is loaded and unloaded at the port of Samil & Ulsan.

• Journal of the East Asian Society of Dietary Life
• /
• v.18 no.5
• /
• pp.725-731
• /
• 2008

The principal objective of this study was to assess the effects of low-calorie diets(LCD) for 8 weeks of medical nutrition therapy in individuals with BMI in excess of $23\;kg/m^2$. 41 over-weight or obese individuals (male=14, female=27, age $28.6{\pm}8.9\;yrs$), none of whom were diagnosed with a medical disease, were administered MNT 4 times over the study period. Approximately $1,100{\sim}1,300\;kcal/day$ were prescribed by a dietitian, via individualized counseling. Anthropometric parameters, daily nutrient intake, and blood levels of leptin, insulin, and lipid profiles were measured prior to and after the 8 weeks of the intervention period. We noted significant reductions in body weight, body mass index (BMI), fat mass (FM), visceral adipose tissue (VAT), abdominal skin-fold thickness, and waist circumference in both men and women. The mean body weight losses in men and women were $3.2{\pm}0.6\;kg$/8 weeks and $2.8{\pm}0.6\;kg$/8 weeks, respectively. However, the % of lean body mass (LBM) in men and women was shown to increase significantly (p<0.05). The daily intake of calorie, fat, protein, vitamin E, folate, and iron were significantly reduced during the LCD period. Blood levels of lipids and glucose were in normal range, and evidenced no changes after LCD. However, the serum levels of leptin in female subjects were significantly reduced (p<0.00l) from $8.9{\pm}4.8\;ng/mL$ to $6.9{\pm}4.8\;ng/mL$. In conclusion, 8 weeks of LCD with individualized counseling by a dietitian effectively reduced body fat and visceral fat in both men and women with BMI in excess of $23\;kg/m^2$.

• Korean Chemical Engineering Research
• /
• v.48 no.2
• /
• pp.185-192
• /
• 2010

The chemical-looping combustion(CLC) has advantages of no energy loss for separation of $CO_2$ without $NO_x$ formation. This CLC system consists of oxidation and reduction reactors where metal oxides particles are circulating through these two reactors. In the present study, the reaction kinetic equations of iron oxide oxygen carriers supported on bentonite have been determined by the shrinking core model. Based on the reactivity data, design values of solid circulation rate and solids inventory were determined for the rector. Two types of interconnected fluidized bed systems were designed for CLC application, one system consists of a riser and a bubbling fluidized bed, and the other one has a riser and two bubbling fluidized beds. Solid circulation rates were varied to about $30kg/m^2s$ by aeration into a loop-seal. Solid circulation rate increases with increasing aeration velocity and it increases further with an auxiliary gas flow into the loop-seal. As solid circulation rate is increased, solid hold up in the riser increases. A typical gas leakage from the riser to the fluidized bed is found to be less than 1%.

• Resources Recycling
• /
• v.31 no.4
• /
• pp.12-18
• /
• 2022

Korea depends on the import of raw materials such as iron ore and coal for the steel industry. These raw materials have a major impact on the cost, productivity, and quality competitiveness in the global steel industry. To secure the competitiveness of steel companies, it is necessary to reduce the country's dependence on raw materials. This can be achieved using byproducts with a high Fe content, which are primarily generated by the steel industry. These byproducts are available in the form of a very fine powder, which can disperse as dust when used directly in plant processes. Dust dispersion has a negative impact on the environment and can lead to the loss of raw materials. To enable the use of a wide range of Fe-containing byproducts, it is necessary to pretreat them in the form of larger aggregates such as pellets and briquettes. There are several methods to achieve such aggregates. There are two ways to produce briquettes: using a hot briquette, which supplies additional heat to produce briquettes, or using a cold briquette, which does not use heat. A method for producing cold briquettes using Fe-containing byproducts was investigated in this study. The yield ratio and briquette strength were examined under various manufacturing conditions.