• 한국세라믹학회지
• /
• 제31권2호
• /
• pp.206-212
• /
• 1994

Effects of the film deposition process parameters on the properties such as deposition rate, etch rate, refractive index, stress and step coverage of plasma enhanced chemical vapor deposited (PECVD) tetraethylorthosilicate glass (TEOS) SiO2 film were investigated and analysed using SEM, FTIR and SIMS techniques. Increasing TEOS flow or decreasing O2 flow increased the deposition rate and the compressive stress of the oxide film but produced a less denser film. The deposition rate decreased owing to the decrease in the sticking coefficient of the TEOS and the O2 molecules onto the substrate Si with increasing the substrate temperature. Increasing the substrate temperature produced a denser film with a lower etch rate and the higher refractive index by lowering SiOH and moisture contents. Increasing the rf power increases the ion bombardment energy. This increase in energy, in turn, increases the deposition rate and tends to make the film denser. No appreciable changes were found in the deposition rate but the refractive index and the stress of the film decreased with increasing the deposition pressure. The carbon content in the plasma TEOS CVD oxide film prepared under our standard deposition conditions were very low according to the SIMS analysis results.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권3호
• /
• pp.316-323
• /
• 1995

A vital step in magnetic tape manufacturing is the surface modification of polymer substrate prior to ink application. A critical element for good adhesion of magnetic ink on polymeric substrate is the ability to join ink in cost-effective manner. Corona discharging is one of the effective methods of modifying polymer surface to improve adhesion while maintaining the desirable properties of the film itself. Surface treatment by corona which is exposure of film surface to electron or ion bombardment, rather than mere exposure to active species, like atomic oxygen or ozone, can enhance adhesion by removing contaminant, electret, roughening surface, and/or introducing reactive chemical groups. Reactive neutrals, ions, electron and photons generated during the corona treatment interact simultaneously with polymers to alter surface chemical composition, wettability, and thus film adhesion. However, it is highly recommended that extensive chains scission be avoided because it can lead to side-effect by forming sticky matter, resulting in dropouts. This paper reviews principles of surface preparation of polymer substrate by corona discharging. In addition, the experimental section provides a description of parameter optimization on corona discharging treatment and its side-effect. Experimental results are discussed in terms of surface wetting as determined by contact angle measurements.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권12호
• /
• pp.785-790
• /
• 1999

This research has been carried out to develop a low-energy large-aperture pulsed electron beam generator (LELA), 200keV 1A, for industrial applications. One of the most important feature of this electron beam generator is large electron beam cross section of $190cm^2$. Low energy electron beam generators have been used for water cleaning, flue gas cleaning, and pasteurization, etc. In these applications the cross sectionof the e-beam is related to reaction efficiency. Another important feature of this LELA EB generator is easy maintenance because of its simple structure and relatively low vacuum operation compared to the conventional EB generators. The conventional EB generators need to be scanned because the small cross section thermal electron emitters are used in the conventional EB generators which have small EB cross section. In this research, we use the secondary electrons generated by ion bombardment on the HV cathode surface as a electron source. Therefore we can make any shape of EB cross section without scanning.

• 한국기계가공학회지
• /
• 제13권2호
• /
• pp.89-93
• /
• 2014

Variable polarity (VP) arc welding is known as an effective solution for aluminum thanks to the cleaning effect, which means oxide removal, during the DCEP (direct current electrode positive) period. In this research, VP GTAW (gas tungsten arc welding) is adopted for lap joint fillet welding of 3mm thickness 5052 aluminum alloy. Various welding currents and DCEP duty cycles are applied as welding conditions with a fixed welding speed to investigate the influence of DCEP characteristics on weld bead formation. Results show a tendency of higher heat input for higher DCEP duty cycle, which result does not follow conventional arc theory because it is known that DCEN (DC electrode negative) polarity is more efficient for heat input than is DCEP. This phenomenonhas recently been reported by several VP-GTA researchers and is still controversial because the mechanism of oxide removal is not yet clear except for the previous, well-known idea of "ion bombardment", which cannot explain the situation. Finally, proper usage conditions for VP-GTAW are suggested; then, further, related theoretical topics in the field of cathode physics are brieflyintroduced.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.203-203
• /
• 2010

Nano-crystalline Si thin films were deposited on polymer and glass by inductively coupled plasma (ICP) - assisted RF magnetron sputtering at low temperature in an argon and hydrogen atmosphere. Internal ICP coil was installed to increase hydrogen atoms dissociated by the induced magnetic field near the inlet of the working gases. The microstructure of deposited films was investigated with XRD, Raman spectroscopy and TEM. The crystalline volume fraction of the deposited films on polymer was about 70% at magnetron RF power of 600W and ICP RF power of 500W. Crystalline volume fraction was decreased slightly with increasing magnetron RF power due to thermal damage by ion bombardment. The diffraction peak consists of two peaks at $28.18^{\circ}$ and $47.10^{\circ}\;2{\theta}$ at magnetron RF power of 600W and ICP RF power of 500W, which correspond to the (111), (220) planes of crystalline Si, respectively. As magnetron power increase, (220) peak disappeared and a dominant diffraction plane was (111). In case of deposited films on glass, the diffraction peak consists of three peaks, which correspond to the (111), (220) and (311). As the substrate temperature increase, dominant diffraction plane was (220) and the thickness of incubation (amorphous) layer was decreased.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 C
• /
• pp.848-850
• /
• 1999

In this study, PZT etching was performed using planar inductively coupled Ar(20)/$Cl_2/BCl_3$ plasma, The etch rate of PZT film was 2450 $\AA/min$ at Ar(20)/$BCl_3$(80) gas mixing ratio and substrate temperature of $80^{\circ}C$. X-ray photoelectron spectroscopy (XPS) analysis for film composition was utilized. The chemical bond of PbO is broken by ion bombardment, and the peak of metal Pb in a Pb 4f peak begins to appear upon etching, decreasing Pb content faster than Zr and Ti. As increase content of additive $BCl_3$, the relative content of oxygen decreases rapidly. We thought that abundant Band BCl radicals made volatile oxy-compound such as $B_{x}O_{y}$ and/or $BClO_x$ bond. To understand etching mechanism, Langmuir probe and optical emission spectroscopy (OES) analysis were utilized for plasma diagnostic.

• 한국재료학회지
• /
• 제7권1호
• /
• pp.8-14
• /
• 1997

DLC막은 여러가지 기술적인 응용에 매우 기대된느 재료이다. 탄화수소 가스의 플라즈마 분해에 의해 증착되는 DLC 막은 높은 경도, 화학적 안정성, 높은 전기 저항성, 적외선 영역의 투과성 등의 여러가지 우수한 성질을 지니고 있다. 그러나 이들막은 높은 내부응력으로 인하여 실제 응용에 상당한 제약을 받고 있다. 본 연구에서는 rf PECVD 법에 의해 합성된 다이아몬드상 탄소막을 보조가스 첨가에 따른 영향에 대하여 조사하였다. 수소가스를 첨가하여 합성된 DLC막의 잔류응력 거동은 낮은 이온 에너지 (V$_{b}$ $P^{1}$2/-20Volt/m Torr)에서 최대 잔류응력이 발생되지만, 질소 가스를 첨가시키면 높은 이온(V$_{b}$ P$_{1}$2/->70Volt/m Torr)에너지 영역에서 잔류응력의 감소가 나타났다. 수소 량이 증가하면 ion bombardment와 식각 작용을 하고, 질소의 경우 막의 표면 스퍼터링 현상이 발생되었다. 보조가스 첨가에 따라 S$P^{3}$net work구조의 생성과 소멸의 결합 구조를 형성하여, 보조가스 첨가는 DLC막의 잔류응력 거동에 영향을 미치는 것을 알 수 있었다. 이온 에너지에 따른막의 비저항은 막 합성 공정 조건에 관계없이 $10^{6}$-$10^{7}$ Ωm 의 범위에서 분포하고 있는 것으로 조사되었다. 이는 메탄가스(rf PECVD)로 합성된 DLC막의 비저항과 거의 일치하는 것으로 나타났다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2000년도 제1회 학술대회 논문집
• /
• pp.85-87
• /
• 2000

In this study, high-density plasma etching characteristics of ITO(indium tin oxide) films used for transparent electrodes in display devices have been investigated. The etch characteristics of ITO as a function of $Ar/CH_4$ gas mixtures were analyzed using QMS(quadrupole mass spectrometry), OES(optical emission spectroscopy), and ESP(electrostatic probe). ITO etch rates were increased with the addition of moderate amount of $CH_4$ to Ar due to the increased chemical reaction between $CH_3$ or H and ITO in addition to the physical sputtering of ITO by Ar ion bombardment. However, the addition of excess amount of $CH_4$ decreased the ITO etch rates possibly due to the increased polymer formation on the ITO surface. Also, the measurement data obtained by QMS and OES suggested that $CH_3$ radicals are more activity involved in the etching of ITO compared to H radicals.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2236-2238
• /
• 1999

This paper deals with the surface glow discharge characteristics and some physical properties of MgO thin films prepared by RF unbalanced magnetron sputtering(UBMS) in surface discharge type AC PDP. The minimum discharge voltage is obtained for the sample of substrate holder bias voltage -10V. The main factors that improves the discharge characteristics by applied bias voltage is considered to be due to the morphology changes or crystal structure of the MgO thin film by ion bombardment during deposition process Moreover, the anti-sputtering characteristics of MgO thin film by UBMS is more excellent than that of balanced magnetron sputtering(BMS) and E-beam evaporation method.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 E
• /
• pp.1758-1760
• /
• 1998

MgO Protecting layer in AC PDP prevents ion bombardment in discharge plasma. The MgO layer also has the additional importance in lowering the firing voltage due to a large secondary electron emission coefficient. Until now, the MgO protecting layer is mainly prepared by E-beam Evaporation. However, the optimum activation manufacturing process of MgO thin film wasn't well known. Therefore in this study, after MgO protecting layer is prepared on dielectric layer by E-beam evaporation and liquid MgO spin coating, we carried out activation process of MgO thin film as a parameter of Temperature, Operating time and Operating pressure. In addition, discharge characteristics are also studied as a parameter of activation conditions.