• 한국산업융합학회 논문집
• /
• 제24권6_2호
• /
• pp.883-890
• /
• 2021

In this study, joint analysis was conducted on the rock slope by aerial surveying using UAV. Aerial photos were taken using UAV to measure the directionality of the rock slope exposed to the site, and the directionality of the joint was analyzed using the photographed photos. UAV photography was taken under conditions of 90% overlap and an altitude of 50m. The photographing path was measured in the horizontal, vertical, and oblique directions based on the slope, and the joint characteristics were analyzed. Aerial surveying research on the joint directionality analysis of rock slopes is still incomplete, and the method for accurate joint directionality analysis is not presented strategically, so it is difficult to apply it in design. Through the results of this study, we would like to propose an flight photographing technique for the investigation of rock joints. As a result of the study, in the case of the joint investigation of the rock slope using UAV, it was necessary to change conditions such as altitude, aerial photography route, and overlap according to the size of the joint according to the site conditions.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.854-861
• /
• 2005

Studied accuracy and practical use possibility of joint measurement that using 3D laser scanner to rock slope. Measured joint of Rock slope and comparison applied 3 dimension laser scanner and clinometer. 3D laser scanning system preserves on computer calculating to 3 dimension coordinate scaning laser to object. and according to laser measurement method of interior, produce correct vector value from charge-coupled device(CCD) or laser reciver and telegram register and time measuring equipment. Create of object x, y, z point coordinates to 3 dimension space of computer. Such 3 dimension point datum (Point Clouds) forms relocate position informations that exist to practical space to computer space. Practical numerical values related between each other. Compared joint distribution and direction that measured by laser scanner and clinometer. By the result, Distribution of joint projected almost equally. Could get more joint datas by measurement of 3 dimension scanner than measured by clinometer. Therefore, There is effect that objectification of rock slope investigation data, shortening of investigation periods, investigation reduction of cost. could know that it is very effective method in joint measuring.

• 산업기술연구
• /
• 제21권B호
• /
• pp.51-58
• /
• 2001

The Distinct Element Method (DEM) was used to analyze the stability of jointed rock slope, of which dimension are about 200m(length), 60m(height), $55^{\circ}$ dip. The Barton-Bandis joint model was used, as a constitutive model. The parameters such as JRC and spatial distribution characteristics of discontinuities were acquired through field investigation. Three different cases such as $51^{\circ}$, $45^{\circ}$ and $38^{\circ}$ in angle of rock slope were analyzed to decide a stable slope. To keep the jointed rock slope safely, it is proposed to reduce the height of slope from 60m to 48m and to reduce the angle of the from $55^{\circ}$ to $38^{\circ}$ too.

• 터널과지하공간
• /
• 제16권5호
• /
• pp.368-376
• /
• 2006

셰일층으로 구성된 암반사면에서 층리면을 따라 대규모 평면파괴가 사면 중앙부에서 발생하였다. 현장조사시 파괴사면 주변은 지하수 누수 흔적과 점토층의 충전물이 존재하였으며, 파괴원인을 검토한 결과 층리면을 따라 형성된 점토 충전물의 낮은 전단강도와 강우시 인장균열내 형성된 수압에 의해 붕괴가 발생한 것으로 나타났다. 그리고 충전된 절리면의 전단강도 특성을 규명하기 위해서 모래, 점토의 인위적인 충전물을 이용하여 충전재 두께비에 따른 전단강도 특성을 고찰하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 추계 학술발표회
• /
• pp.256-267
• /
• 2006

After heavy rainfall, It was occurred massive plane failure along bedding plane of shale in the center of rock slope. It was observed filling material and trace of underground water leakage around of the slope. We tried to find the cause for slope failure, and the result of examination showed that primary factors of the failure were low shear strength of clay filling material and water pressure farmed within tension crack existed in the top of the slope. In this research, in order to examine the features of shear strength of filled rock joint, shear test of filled rock joint was conducted using of artificial filling material such as sand and clay. Also we made an investigation into the characteristics of shear strength with different thickness of filling materials.

• 지질공학
• /
• 제17권2호
• /
• pp.289-297
• /
• 2007

매년 강우로 인해 발생되는 사면파괴는 많은 재산피해와 인명피해를 발생시키고 있다. 사면재해로부터의 피해저감을 위해 인간의 생활권과 인접한 사면에 대한 지속적인 관리를 통해 이들의 안정성 검토와 보강 대책이 요구된다. 연구지역은 편마암으로 이루어진 암반사면으로써 단층작용으로 인해 대규모 절리군이 형성되어 있는 풍화암 내지 연암의 풍화 특성을 보여준다. 조사사면을 자연사면과 절취사면으로 구분하여 현장자료를 검토한 결과, 자연사면에서는 주 절리군이 형성된 4개 지점에서 평면파괴와 쐐기파괴 가능성이 우세하였으며, 절취사면의 경우 8개 지점에서 쐐기파괴 발생 가능성이 높게 나타났다. 또한 SLIDE 2D에 적용해 이들 사면의 최소안전율에 대한 수치해석 결과에서는 자연사면보다 절취사면의 안정성이 비교적 취약한 것으로 분석되었다.

• 화약ㆍ발파
• /
• 제28권2호
• /
• pp.1-16
• /
• 2010

본 연구에서는 암반사면형성 작업시 최종벽면에 적용된 프리스플리팅(pre-splitting) 발파공법의 발파효과와 관련하여 발파 후 벽면의 암반손상이 장약된 폭약의 폭력 보다는 암반 내에 발달된 불연속면의 발달 형태에 따라 더 큰 영향을 보일 수 있음을 규명하였다. 이를 위하여 불연속면을 대표할 수 있는 절리에 대한 조사를 통해 발파 후 벽면 암반의 절리군 분포양상을 4가지 Case로 분류하고, 파쇄도 분석 영상처리시스템을 통해 벽면에 나타나는 암반블록의 크기 빈도를 비교 분석함으로써 벽면의 암반손상도를 파악하였다. 절리군이 1개 이하로 발달하는 경우, 분석된 블록의 크기 중 2,000mm 이상 되는 부분이 42%를 차지하여 프리스플리팅 발파공법의 효과를 뚜렷이 확인할 수 있었으며, 2~3개의 절리군이 일방향으로 발달하는 경우와 교차되면서 발달하는 경우, 블록의 크기는 1,000~2,000mm 사이에 각각 43.6% 및 35.8%의 빈도로 분포하는 것으로 나타나 프리스플리팅 발파공법에 의한 발파효율이 다소 떨어지는 양상을 보였다. 그러나 3개 이상의 절리군이 불규칙하게 발달하는 경우에는 블록의 크기가 250~500mm 사이에 35%의 빈도로 분포하고 1,000mm 이상의 크기에 대해서는 거의 나타나지 않는 양상을 보였다. 따라서 이러한 경우 프리스플리팅 발파공법에 의한 발파 효과는 거의 없이 일반적인 발파가 이루어졌다고 볼 수 있었다. 또한 PFC2D에 의한 발파수치해석결과, 암반 내부로의 손상영역 발생은 본 발파보다는 프리스플리팅 발파공법에 의해 직접적인 영향을 받을 수 있음을 확인하였으며, 따라서 향후 사면 형성을 위한 프리스플리팅 발파공법을 적용할 경우에는 사전 지표지질조사를 시행하여 절리를 비롯한 불연속면과 관련된 사항을 충분히 파악할 필요가 있으며, 시공진행에 따라 예상보다 많은 절리군이 나타날 경우에는 프리스플리팅 발파공법의 설계 조정이 필요할 것으로 판단된다.

• Geomechanics and Engineering
• /
• 제14권3호
• /
• pp.271-281
• /
• 2018

A jointed rock slope stability evaluation was simulated by a discontinuous deformation analysis numerical method to investigate the process and safety factors for different crack distributions and different overloading situations. An optimized method using Discontinuous Deformation Analysis for Rock Failure (DDARF) is presented to perform numerical investigations on the jointed rock slope stability evaluation of the Dagangshan hydropower station. During the pre-processing of establishing the numerical model, an integrated software system including AutoCAD, Screen Capture, and Excel is adopted to facilitate the implementation of the numerical model with random joint network. These optimizations during the pre-processing stage of DDARF can remarkably improve the simulation efficiency, making it possible for complex model calculation. In the numerical investigations on the jointed rock slope stability evaluations using the optimized DDARF, three calculation schemes have been taken into account in the numerical model: (I) no joint; (II) two sets of regular parallel joints; and (III) multiple sets of random joints. This model is capable of replicating the entire processes including crack initiation, propagation, formation of shear zones, and local failures, and thus is able to provide constructive suggestions to supporting schemes for the slope. Meanwhile, the overloading numerical simulations under the same three schemes have also been performed. Overloading safety factors of the three schemes are 5.68, 2.42 and 1.39, respectively, which are obtained by analyzing the displacement evolutions of key monitoring points during overloading.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.833-841
• /
• 2008

Recently, the upheaval generation in the road which is under service had been reported. Due to the upheaval generation, total 4 lanes were forced to curtail to 3 lanes, and traffic was delayed. In normal situation of cut-slopes in korea, that condition is hard to detect since most cut-slopes contain discontinuous material, that is rock. Common collapses in rock-slopes is wedge failure, plane failure and toppling failure which is all individual mechanism of discontinuous rock mass. In contrast, such upheaval in the road in front of cut-slope can be generated only when circular movement is triggered within the cut-slope. In this sense, rock-slopes barely show any kind of movement in the road locates at the front of them. Numerical analysis is general method in simulation of slope displacement and evaluation of safety. However, numerical analysis programs which are related with rock-slopes are not able to simulate such upheaval movement because that programs are based on discontinuous modeling mechanism. In addition, although numerical analysis programs which are based on FEM/FDM and thus utilize continuous modeling mechanism are able to simulate circular movement and upheaval situation, they have weakness in reflecting discontinuities of rock-slope itself. In this study, detailed in-site investigation and numerical analysis based on in-site condition were performed in order to expect upheaval movement in the road. In this procedure, the FLAC program which uses continuous modeling method was utilized, and new approach reflecting discontinuity developed toward the road with a ubiquitous joint model was tried to derive reliable analysis result.

• 한국철도학회논문집
• /
• 제12권4호
• /
• pp.548-556
• /
• 2009

암반절취사면의 지질구조를 측정하기 위하여 개발된 조사시스템의 현장 적용성을 겸토하기 위하여 절취사면에 대해 클리노 컴퍼스와 조사시스템을 이용하여 암반 불연속면을 1차 7개, 2차 10개를 측정하여 그 결과를 비교하였다. 1차 시험은 불연속면의 절리형태와 경사각에 따른 측정 결과 값의 차이를 비교하였고, 2차 시험은 촬영 시간과 촬영위치를 달리하여 비교분석하였다. 비교 결과 1차 시험은 클리노 컴퍼스로 측정한 값과 경사방향 $1^{\circ}{\sim}4^{\circ}$, 경사각 $0^{\circ}{\sim}4^{\circ}$의 차이를 보였고, 2차 시험은 경사방향 $0^{\circ}{\sim}6^{\circ}$, 정사각 $0^{\circ}{\sim}6^{\circ}$의 차이를 보였다. 일반적으로 클리노 컴퍼스를 활용한 암반 불연속면 조사시 표면상태가 고르지 않고 측정위치에 따른 경사방향과 경사각의 차이가 ${\pm}10^{\circ}$정도 나타날 수 있다는 점과 측정자의 숙련도에 따른 오차를 감안할 때 본 조사시스템의 정확성에 대한 신뢰도는 비교적 높은 것으로 나타났다.