• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.10
• /
• pp.1040-1047
• /
• 2002

In this paper, we investigated noise decoupling on the power bus by the screw connection, used to the mechanical join and grounding of the PCB ground to chassis. The screw connection penetrates the power bus and then it affects noise propagation on the power bus. To verify effect of the screw connection, we compare bare board with board having screws connection with 0.5 mm separation between power bus and chassis. From these results, we observed that the power bus noise was decreased about 5 dB at the frequency range from 0.1 GHz to 1 GHz. Also, we verified that a 4-layer PCB with signal trace had the better signal quality up to 600 MHz by the screw connection. Therefore, these results will be useful in designing to the high speed circuit and chassis.

• Korean Journal of Materials Research
• /
• v.20 no.1
• /
• pp.19-24
• /
• 2010

The current study examined Ag migration from the Ag paste bump in the SABiT technology-applied PCB. A series of experiments were performed to measure the existence/non-existence of Ag in the insulating prepreg region. The average grain size of Ag paste was 30 nm according to X-ray diffraction (XRD) measurement. Conventional XRD showed limitations in finding a small amount of Ag in the prepreg region. The surface morphology and cross section view in the Cu line-Ag paste bump-Cu line structure were observed using a field emission scanning electron microscope (FE-SEM). The amount of Ag as a function of distance from the edge of Ag paste bump was obtained by FE-SEM with energy dispersive spectroscopy (EDS). We used an electron probe micro analyzer (EPMA) to improve the detecting resolution of Ag content and achieved the Ag distribution function as a function of the distance from the edge of the Ag paste bump. The same method with EPMA was applied for Cu filled via instead of Ag paste bump. We compared the distribution function of Ag and Cu, obtained from EPMA, and concluded that there was no considerable Ag migration effect for the SABiT technology-applied printed circuit board (PCB).

• Journal of the Korean Institute of Navigation
• /
• v.24 no.1
• /
• pp.13-22
• /
• 2000

The collisions at sea among marine casualties are not reduced as the tonnage and speed of ship's increase as well as the traffic quantity increase at sea, in spite of the improvement of nautical equipment, enforcement of crew's education and training as well as improvement of quality standard according to the implementation of ISM code. The measures to prevent the collisions at sea are simple, and are composed of six stage.: The first stage is that the officer on duty detect the target from his eye or radar information. The second stage is determining the type and kind of target-ship. The third stage is target tracking; calculation of target speed, course, CPA and TCPA from radar information or visual check. The fourth stage is determination of vessel in danger after calculation of third stage. The fifth stage is the judgement of situation if own ship is stand-on or give way vessel according to the 1972 COLREG. The last stage is to carry out proper action according to 1972 COLREG, under the circumstances. But by the case, the situations are so different under the different external conditions; for example, natural/navigational conditions, crew's human factors, ship's particular, rule or regulation, management system on board, the condition of watch keeping. Therefore the reasons and casualties are so complicated. This study aims to investigate the collision casualty at sea which needs to clarity all these causal factors of afore-mentioned, and to analyze the causes of problems so as to utilize them to establish the measures of preventing marine accidents. This study, described the concepts of causal factors into three groups; environmental factor, and company/on board management system and navigator's act. Also described how to investigate and analyzes the casual factors. Even though it was described in this paper how to detect the causal factors and reasons of collisions, and how to analyze the inter-relation of each causal factors, it is necessary to do further study how to analyze between the liability of concerned parties and the casual factors involved.

• International conference on construction engineering and project management
• /
• 2011.02a
• /
• pp.413-419
• /
• 2011

Corporate governance is a system articulating the division of responsibilities among different company members, and defining the running rules and procedures for making decisions on corporate affairs. The separation of ownership and management in modern enterprises brings agency problems to the company shareholders, and it is wildly believed that good practice on corporate governance is essential to prevent managers from taking actions by which profiteering their own benefits but compromising the interests of shareholders. This research investigates the level of companies' compliance with the corporate governance codes to find whether significant differences in corporate governance practice exist between the listed construction companies and the national leading companies in Taiwan. Further exploration focuses on the correlation between the compliance level and the industrial features. The investigation finds that: (1)Construction companies display lower levels of corporate governance compliance; (2)Construction companies display lower levels of structural board independence and respect for stakeholders; (3)Compliance levels of construction companies are correlated with the number of employees and the ownership concentration; (4)Compliance levels of the whole sample companies are correlated with the factors representing firm size, such as turnover, capital and number of employees, but are independent of profitability as well as stock price volatility. The above empirical evidence characterizes the features of corporate governance in Taiwan listed construction companies, including: (1)Large companies lurking high risk of agency problems have more willingness to conduct corporate governance and meanwhile can afford higher costs for the conduction, so that their compliance level would be higher than smaller companies; (2)Construction companies in Taiwan have higher ownership concentration, on account of the industrial tradition of family business, and therefore pay less attention to the compliance with structural board independence and respect for stakeholders. However, the conclusions indicate that further studies are essential to clarify whether the above disparities would lead to a negative cycle of corporate governance practice in construction industry. The benefits of corporate governance should unfold more evidently to convince construction companies for improving their investment environment and stimulating their healthy growth.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.132-137
• /
• 2018

Although the number of chemical accidents has been declining since the Chemical Control Act of 2015, there have been repeated occurrences of similar types of accidents at printed circuit board (PCB) manufacturing facilities. These accidents were caused by the overflow of hydrochloric acid and hydrogen peroxide, which are toxic chemicals used in the printed circuit board manufacturing process. An analysis of the $Cl^-$ content to identify the cause of the accident showed that in the mixed route of hydrochloric acid and hydrogen peroxide, which are accidental substances, the $Cl^-$ concentration was 66.85 ppm in the hydrogen peroxide sample. Through reaction experiments, it was confirmed that the deformation of a PVC storage tank and generation of chlorine gas, which is a toxic gas, occurred due to reaction heat occurring up to $50.5^{\circ}C$. This paper proposes a facility safety management plan, including overcharge, overflow prevention, leak detection device, and separation tank design for mixing prevention in printed circuit board manufacturing facility etch process. To prevent the recurrence of accidents of the same type, the necessity of a periodic facility safety inspection and strengthening of the safety education of workers was discussed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.1
• /
• pp.81-88
• /
• 2020

Flight data recorder is a equipment that records data required for investigation of aircraft accidents and should be developed in compliance with the ED-112A standard. Unlike general data storage device, flight data recorder must be able to recover data after an aircraft accident, requiring a housing and a memory board to protect data in extreme environments. To attain this performance, we designed a housing that can withstand the test by analyzing the physical environment of the impact, shear/tensile, penetration resistance and static crush test of the crash survival test and minimized the size and weight compared to the existing one in consideration of the installation of the aircraft in this paper. Insulation material and thermal block material were applied to endure high and low temperature fire so that the internal temperature does not rise above 150℃ even in 260℃, 10 hour environment. In addition, the memory board is designed to minimize the size and we devise a hoping programming method to prevent continuous data loss of more than 16 seconds. Through this, Crash protected memory module that satisfies ED-112A was completed.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.32 no.4
• /
• pp.331-339
• /
• 1996

It is most important to understand the behaviour of fish in case of the betterment of the current fishing gear and methods or the development of the conditioning by acoustic sound in marine ranching. This investigation has been attempted to provide for the prediction of the response action of fish to acoustic sound. The experimental fish was conditioned with sound and bait. As the acoustic sound for stimulus, the pure tone of sine waveform at the frequency of 200Hz was used. This pure tone was determined from previous investigation about hearing ability of walleye pollock Theragra chalcogramma. The fork length of walleye pollock used in this experiment was 385~450mm. The conditioning proceeding was recorded in the video tape recorder. Frequency of appearance in the feeding area was analyzed with computer and video tape recorder. The position of fish was tracked using the mouse cursor and picture mixed on the superimpose board. The response of conditioned fish to sound stimulus was appeared in the 8th day firstly. The conditioned fish remembered the stimulus sound for 4 days. Average frequency of appearance in the feeding area during the 30 seconds sound projection or 1 minute after the sound stimulus was 51%, and was higher than before it.

• Korean Chemical Engineering Research
• /
• v.56 no.6
• /
• pp.811-818
• /
• 2018

A fire and explosion accident caused by a liquefied petroleum gas (LPG) welding and cutting torch gas leak occurred 10 m underground at the site of reinforcement work for bridge columns, killing four people and seriously injuring ten. We conducted a comprehensive investigation into the accident to identify the fundamental causes of the explosion by analyzing the structure of the construction site and the properties of propane, which was the main component of LPG welding and cutting work used at the site. The range between the lower and upper explosion limits of leaking LPG for welding and cutting work was examined using Le Chatelier's formula; the behavior of LPG concentration change, which included dispersion and concentration change, was analyzed using the fire dynamic simulator (FDS). We concluded that the primary cause of the accident was combustible LPG that leaked from a welding and cutting torch and formed a explosion range between the lower and upper limits. When the LPG contacted the flame of the welding and cutting torch, LPG explosion occurred. The LPG explosion power calculation was verified by the blast effect computation program developed by the Department of Defense Explosive Safety Board (DDESB). According to the fire simulation results, we concluded that the welding and cutting torch LPG leak caused the gas explosion. This study is useful for safety management to prevent accidents caused by LPG welding and cutting work at construction sites.

• Journal of electromagnetic engineering and science
• /
• v.5 no.3
• /
• pp.140-145
• /
• 2005

In this paper, an experimental investigation for return loss and a software-based prediction for interference level of single-packaged filtering antenna composed of dielectric waveguide filter and PCB(Printed Circuit Board) slot antenna in transceiver module have been carried out with several different feeding structures in millimeter-wave regime. The implementation and embedding method of the existing air-filled waveguide filters working at millimeter-wave frequency on general PCB substrate have been described. In a view of the implementation of each components, the dielectric waveguide embedded in PCB and LTCC(Low Temparature Co-fired Ceramic) substrates has employed the via fences as a replacement with side walls and common ground plane to prevent energy leakage. The characteristics of several prototypes of filtering antenna embedded in PCB substrate are considered by comparing the wideband and transmission characteristics as a function of bent angle of transmission line connecting two components. In addition, as an essential to the packaging of transceiver module working at millimeter-wave, miniaturization technology maintaining the performances of independent components and the important problems caused by integrating and connecting the different components in different layers are described in this paper.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.2
• /
• pp.109-116
• /
• 2003

An investigation on the structural behavior of cold-formed steel lipped C-section stud for interior walls or partitions was carried out. This experimental research was carried out to study the ultimate and service load capacity of stud assemblies that are subjected to lateral loads. Each test specimen consisted of three or four lipped C-section studs and two C-section tracks that restrained both ends. The major factors considered in this experiment were the perforation on the web, the connection of the bridge channel and the special clip. The effect of the plaster board and the ply wood, which were attached to the tension flange on the flexural strength, was also investigated. Thereafter, the test strength capacities were compared with the nominal strength, based on the AISI Specifications (1996).