• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1442-1444
• /
• 2000

High speed switching action of PWM inverter is being further advanced for electric motor vehicles. Due to this high speed switching action, extensive high frequency electromagnetic noise emerges. Therefore counterm-easures against electromagnetic interference of electric motor vehicles become increasingly important. This paper describes the theory and countermeasure principle of EMI prevention and EMI test method for Korean Standard EMU.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.108-110
• /
• 1999

In this paper, approximate means of estimating the flux and torque levels in an induction motor is discussed. There exists several method that is used directly by flux meter and flux sensing coils in the airgap. Most of these methods are sensitive to motor parameter value changes. Also, the harmonics in the motor voltage and current due to the nonsinusodial inverter waveform cause errors in the estimated torque. Finally, this result is applicated in arch type linear induction motor for study of noise and vibration.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.4
• /
• pp.219-221
• /
• 2002

This paper presents an electric scooter development using blushless DC motor. In recent scooters was to develop for sport leisure and short transportation. Most of scooter are used petroleum gas. This gas scooter has disadvantage to pollute the air. Some of scooters have developed by DC motor which require a brush. However brushless motors have higher maximum speed and greater capacity, save maintenance labour and produce less noise. There is also greater freedom in planing the usage of brushless motors. In this paper we develop an electric scooter driving BLDC motor for design smart system and control speed of scooter with current reference signal to apply voltage to motor by means of three phase inverter. Using accelerator device we generate current reference to control speed and send the current to a MICOM by A/D converter. This MICOM produces the voltage signal and hall sensors signal and PWM controller drive three phase inverter to minimize error between the reference and an actual current.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.265-267
• /
• 2007

본 논문은 LCD Backlight 구동을 위한 새로운 방식의 회로를 제안한다. 제안된 회로는 Charge Pump 캐패시터를 이용한 Half-Bridge 타입의 인버터로 Full Bridge 회로와 동등한 성능을 갖는다. 제안 회로는 넓은 입력 범위와 넓은 부하 범위에서 영전압 스위칭(ZVS) 확보가 가능해서 인버터의 고효율 동작이 확보되고, MOSFET의 surge 및 noise를 저감시킨다. 제안된 회로의 동작 원리를 설명하고, 시뮬레이션 및 40" LCD 패널에 실제 적용 실험하여, 회로의 동작을 입증하였다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.12
• /
• pp.1737-1741
• /
• 2015

A multi-channel CMOS transimpedance amplifier(TIA) array is realized in a $0.18-{\mu}m$ CMOS technology for the applications of panoramic scan LADAR systems. Each channel consists of a PIN photodiode and a feed-forward TIA that exploits an inverter input stage followed by a feed-forward common-source amplifier so as to achieve lower noise and higher gain than a conventional voltage-mode inverter TIA. Measured results demonstrate that each channel achieves $76-dB{\Omega}$ transimpedance gain, 720-MHz bandwidth, and -20.5-dBm sensitivity for $10^{-9}$ BER. Also, a single channel dissipates the power dissipation of 30 mW from a single 1.8-V supply, and shows less than -33-dB crosstalk between adjacent channels.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.2 no.4
• /
• pp.56-64
• /
• 1997

최근 용접분야에서는 용접성능을 향상시키기 위하여 인버터회로를 용접기에 적용한 인버터 용접기에 관한 연구가 활발히 진행되고 있다,. 그러나 범용의 인버터 용접기의 경우 다이오드 정류기를 사용함에 저차의 전류고조파가 발생하고 시스템 역율을 저하시킨다. 따라서 본 논문에서는 인버터 아크 용접기의 역율개선을 위한 PWM 컨버터에 관하여 연구하여 입력전류의 저차 고조파를 저감하였고 전원전압과 동상으로 전원전류를 제어함에 의한 단위 역율형 인버터 용접기의 특성을 해석하였다. 또한 본 논문에서는 에너지 절약, 용접 특성, 역율, 사용율, 크기 및 부피 등의 관점에서 인버터 아크용접기의 응용연구 및 실험적 분석을 수행하였고 용접기 시스템에서 발생하는 전기적 노이즈를 억제하고 전력용 반도체 소자를 보호할 목적으로 새로운 노이즈 차폐변압기를 채택하였다. 이상의 전체시스템은 싱글칩 마이크로 프로세서를 이용한 디지털 제어기로 구현함으로서 제어기의 유연성과 기능의 다양화를 추구하였다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.7
• /
• pp.1204-1210
• /
• 2016

The phase currents must be accurately measured to achieve the instantaneous torque control of AC motors. In general, those are measured using the current sensors. However, the measured current signals can include the offset errors and scaling errors by several components such as current sensors, analog amplifiers, noise filter circuits, and analog-to-digital converters. Therefore, the torque-controlled performance can be deteriorated by the current measurement errors. In this paper we have analyzed the influence caused by vector control of 2-phase induction motor when two errors are included in measured phase currents. Based on analyzed results, the compensation method is proposed without additional hardware. The proposed compensation method was applied vector-controlled inverter for 2-phase induction motor of 360[W] class and verified through computer simulations and experiments.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.273-277
• /
• 1999

A cold cathode flourescent lamp for the backlight in the notebook computer requires high input voltage about 1300(V) when it turns on. But once a discharge starts, the input voltage can be dropped by about one-third for continued output. The equivalent impedance also varies from open to several dozens of kilo-ohms. The piezoelectric transformer converts electrical energy into mechanical energy and then converts it back to electrical energy at a high voltage. Its high output voltage, high efficiency and small size are suitable for driving the LCD backlight in the notebook computer. The piezoelectric transformer operates near the resonance frequency and the output waveform is close to sine wave with very little noise. This paper suggests an inverter for LCD backlight of notebook computer using piezoelectric transformer that includes voltage to frequency converter for gate signal which is useful for tracking of variable resonance frequency depending on load impedance.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.4
• /
• pp.318-330
• /
• 2013

This paper presents a high-linearity low-noise small-size programmable gain amplifier (PGA) based on a new low-noise low-distortion differential amplifier and a proposed reconfiguration technique. The proposed differential amplifier combines an inverter-based differential pair with an adaptive biasing circuit to reduce noise and distortion. The reconfiguration technique saves the chip size by half by utilizing the same differential pair for the input transconductance and load-stage, interchangeably. Fabricated in $0.18-{\mu}m$ CMOS, the proposed PGA shows a dB-linear control range of 21dB in 16 steps from -11 dB to 10 dB with a gain error of less than ${\pm}0.33$ dB, an IIP3 of 7.4~14.5 dBm, a P1dB of -7~1.2 dBm, a noise figure of 13dB, and a 3-dB bandwidth of 270MHz at the maximum gain, respectively. The PGA occupies a chip area of $0.04mm^2$ and consumes only 1.3 mA from the 1.8 V supply.

• Journal of Power Electronics
• /
• v.14 no.5
• /
• pp.1057-1068
• /
• 2014

Phase-locked loops (PLL) based on the synchronous reference frame (SRF-PLL) have recently become the most widely-used for grid synchronization in three phase grid-connected inverters. However, it is difficult to study their performance since they are nonlinear systems. To estimate the performances of a SRF-PLL, a canonical small-signal linearized model has been developed in this paper. Based on the proposed model, several significant specifications of a SRF-PLL, such as the capture time, capture rang, bandwidth, the product of capture time and bandwidth, and steady-state error have been investigated. Finally, a noise model of a SRF-PLL has been put forward to analyze the noise rejection ability by computing the SNR (signal-to-noise ratio) of a SRF-PLL. Several simulation and experimental results have been provided to verify and validate the obtained conclusions. Although the proposed model and analysis method are based on a SRF-PLL, they are also suitable for analyzing other types of PLLs.