• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.154-156
• /
• 1993

In this paper, fault analysis using simulation method and fault diagnosis scheme are presented for induction motor drive system. Major faults such as inverter 'a' phase open fault, inverter 'a'-'b' phase short circuit fault and inverter 'a' phase ground fault are analyzed and simulated. On-line and off-line fault diagnosis systems are proposed.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1999.11a
• /
• pp.181-183
• /
• 1999

This paper is about the design of half-bridge inverter controller with low cost and simple configuration for low power single-phase induction motor driving. The simple controller is composed of MCU and PLD. Also, to limit the overcurrent at initial driving, auxiliary function is added, and stabilizes the system. In order to verify the performance of the proposed methode, we design 500W inverter system, and in result, the response time of the proposed method compared with line voltage driving method is reduced by 200[msec].

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.10-13
• /
• 1998

In this paper, a control strategy of the three phase ZVT inverter for ac motor drives is proposed. The topology of ZVT inverter analyzed with a description of the control conditions dependent on the load current and MSVM(Modified Space Vector Modulation). The detailed simulation results indicate that zero-voltage operation during transition of the MSVM algorithm can be achieved.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.12
• /
• pp.854-861
• /
• 1988

The current source inverter-fed induction motor(CSIM) drive is widely used in industry because of its four quadrant operation, fuseless protection, fuseless protection, and ruggedness. the CSIM drive system, however, has shortcomins such as slow response and dynamic stability to load torque disturbance and reference speed change. Such a disadvantages can be compensated considerably by means of introducing additional angle angle control loop. The angle control method is dependent upon the inverter type. In this paper, simultaneus recovery and commutation inverter(SRCI) which is developed recently is considered.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.216-218
• /
• 2008

This paper presents a space vector pulse width modulation (SVPWM) technique for four-switch three-phase (4S3P) inverter topology. The method aims to apply Field Oriented Control (FOC) of Induction motor using 4S3P. The simulations are carried out and the experimental results are given to verify the feasibility of this method.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.207-210
• /
• 2000

In this paper a theoretical formulation of the direct control relating the action exerted by the inverter space vectors on the stator flux and the torque of Induction motor is analyzed. From the equation the scheme of the inverter switching is proposed and influence of the stator flux and the electromagnetic torque in each switching pattern is also analyzed.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.53 no.1
• /
• pp.14-21
• /
• 2004

Most adjustable-speed drives (ASDs) designed to operate low voltage induction motors incorporate voltage-source inverters (VSIs), which create motor voltages at high switching frequencies. The motor leads used to connect an ASD to a motor can behave like transmission lines for voltage pulses, which can be reflected at the motor terminals. The resulting oscillatory transient, known as the long-lead effect, can stress and consequently degrade the stator insulation system of a motor. This paper describes the results of tests to 1) determine the correlation between peak motor voltage and the length of motor leads and 2) determine the correlation between peak motor voltage and the switching frequency of the ASD Insulation failures like this usually are caused by voltage surges. Voltage surges are often the result of switching power circuits, lightning strikes, capacitor discharges and solid-state power devices.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1095-1097
• /
• 1993

The double excited induction motor has two sets of three-phase system : One is connected to the ac source to take care of energy convertion, and the other is to the inverter controlable frequency and/or magnitude of voltage, both of the induction mode and the synchronous mode are possible in double excitation motor, and the proposed double excitation motor can be driven as a synchronous motor by the extra three-phase input. At the synchronous mode the efficiency is improved so higher than that at induction mode or induction motor. The rating of the inverter used for speed control can be reduced upto one-fifth of that for conventional induction motor. Also the cost and maintenance fee of double excitation induction motor can be reduced compared to any other motors.

• Proceedings of the KSR Conference
• /
• 1998.11a
• /
• pp.187-193
• /
• 1998

An inverter-driven induction motor is used as the traction motor for a high speed drive system that required safty, reliability and performance and so on. rotor bar and end ring of the traction motor are the electrical equipments which form the conductive close loop and then induce current by interaction wi th the current of stator. the materials selection of rotor bar and end ring are seriously considered in the aspects of electrical and mechanical specification and Motor slip relation to inverter. Particularly motor slip guarantee the safty and reliability of induction motor. this paper show the material selection and the determining of slip in the design of traction motor for high speed train by analyzing the specifications of material being used currently.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.950-954
• /
• 1998

This paper describes a development of traction unit for 2-motor driven electric vehicle (EV). The traction unit is consisted with an interior permanent magnet synchronous motor (IPMSM), a reduction gear and an inverter for electric vehicle that is driven by 2 motors without differential gear. For traction unit, prototype IPMSM and inverter have been developed. The IPMSM was designed by CAD program that was developed with both equivalent circuit method and FEM. Also the inverter was developed to drive 2 motors with 6 legs IGBT switches in a control board. The vector control algorithm was implemented with maximum torque control method in the constant torque region and field weakening control method in the constant power region considering inverter capacity. To verify that the traction unit is more high efficiency and has more high power density than a traction unit with induction motor with the same power, we would like to show the results about the design and analysis of the IPMSM and the experiment results about the traction unit.